Ningbo FG-S1200 Manual de usuario
DRYWALL SANDER
FG-S1200
INSTRUCTION MANUAL
1
Contents
1. Warning & Statements。。。。。。。。。。。。。。。。。。。。。。。。。。。。。
1-4
2. Voltage。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。
4
3. Device Application。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。
4
4. Technical Specifications。。。。。。。。。。。。。。。。。。。。。。。。。。。。。
4
5. Structure Overview。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。
6-7
6. Installation & Sandpaper Replacement。。。。。。。。。。。。。。。
7-9
7. Installation & viscid disc Replacement。。。。。。。。。。。。。。。
9-10
8. Connection Set for Dust Outlet。。。。。。。。。。。。。。。。。。。。
10-13
9. Switch& Speed Governor operation。。。。。。。。。。。。。。。
13-14
2
10. Application Diagram。。。。。。。。。。。。。。。。。。。。。。。。。。。
14-16
11. Cleaning。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。
16
12. Replacement of carbon brush。。。。。。。。。。。。。。。。。。。。
16-17
1．Warning & Statements
Note：In order to reduce the hazards of fire, electrical shock
and injury, etc, the statements listed below shall be taken into
consideration upon application of electric tools.
1．Understand your electric tool fully by going through the user
manual carefully together with identifying the application,
limitation and potential risk accordingly.
2．Adopt protective appliances and act by conforming to the
due order strictly.
3．Remove all the regulatory instruments, and form the habit to
check about that prior to application of electric tools.
4．Keep the operational site clean. Accidents are most likely to
occur in case that the electric tools are used in a messy and
dirty place, or on the workbench.
5．Any operation in unsafe conditions is strictly prohibited. Do
3
not use the electric tools in places exposed to damp/moisture,
or leave them outside in rainy days. Make sure to keep the
operational site bright enough.
6．Keep the children away from the devices. Certain distance
shall be guaranteed as for the children in search of on-site
operational experience.
7．Actions shall be taken to avoid the workshop accessible by
children without permission, such as locking the door,
cutting off the power supply or taking away the launch key.
8．Do not use the devices at will. To ensure the overall quality
of work piece and maintain security anyway, please use the
devices within the design capacity.
9．Use the devices correctly, and do not operate them in
overloading or abnormal status.
10．Ensure appropriate clothing. Do not wear loosen clothes,
gloves, tie, knot, etc. which may result in hazards of being
entangled by running devices. Prefer shoes with skid proof to
avoid slipping, and cut the hair to the proper length.
11．Remember to wear protective spectacles. Abundant dust may
come out in the buffing process, thus it’s necessary to wear
dust mask. Glasses in daily use incorporate lens with impact
resistance only, which could by no means meet the safety
requirements.
12．Do not place your hands over the twisting disk. Meanwhile,
stand still during the operations.
13．Prior to adopting the device, check if the disk suffers from
defects as rupture and the sandpaper is well-composed.
14．Ensure tight connections at the disk and other joints.
15．When using the device, remember to hold the handle firmly.
4
Single-hand operations and any intentions to touch the disk
are strictly prohibited.
16．Before switching on, the disk shall be away from any contact
of other objects.
17．Prior to application, the device shall be powered and
switched on to make the disk twist at full speed. Avoid waver
arising from installation error and misplaced disk. In case of
any malfunction, cut off the power supply and cease the
operations at hand immediately.
18．Treat the device maintenance cautiously. Keep the grinder
sharp and safe at any time. In addition, follow the
instructions to lubricate the device and replace appropriate
accessories.
19．The power supply must be cut off during maintenance, such
as the replacement of accessories, sandpaper, etc.
20．Avoid direct connection to power supply. Before power on,
check if the switch for the device is off in advance.
21．Use the accessories according to the instructions. Read
through the user manual in details, and select right
accessories accordingly, otherwise, it may result in
unexpected injuries.
22．Check if the components or devices are damaged at any time.
In case of any failure or abrasion, replace the device at once.
Otherwise, it may affect working efficiency or even result in
accidents.
23．Keep an eye on the device to cancel it. Make sure to switch
off, and wait until the device finally ceases.
24．As for adoption of the device, only apply specified parts for
replacement.
5
25．In case of maintenance or replacement, adopt specified
spare parts only.
2．Voltage
Before connecting electric tool to the socket, make sure that
the supply voltage be in accordance with rated voltage. If the
former is greater than latter and the device is powered on by
mistake, it may result in damage of devices and injuries of people.
As for indefinite supply voltage of socket, never try to plug for
use. Besides, the damage of devices may also occur if the supply
voltage falls below rated voltage.
3. Device Application
As one of our products, the device belongs to the hand-held
electric tools.
The device mainly caters for lime surface, including the
interior wall, ceiling, exterior wall, corridor, etc. Remove the
painting lime mud from the wall, and make the surface even or
smooth. It may promote the wall grinding efficiency and quality
by workers.
With various conditions taken into consideration in the
design, the device may run at high or low speed to optimize the
grinding efficiency and realize user-friendly and compact design.
6
4. Technical Specifications
Model FG-S1200
Rated Voltage 230/110（V）
Frequency 50/60（Hz）
Rated Power 1200
（W）
No-load Speed 1500-3300(R/min)
Sandpaper Dimensions Ф225
（mm）
Safety Standard II /
Net/Gross Weight 2.7/4.1（kg）
Machine size 300*258*258
（mm）
Packing Dimensions 27.5*27.5*28（cm/pc）
5．Structure Overview (See following pictures)
7
sandpaper plastic disc component brush
Standard Accessories
Sandpaper: 6 pc Allen Wrench: 1 pc
Carbon Brush: 2 pc Telescopic Dust hose: 2 m/1 pc
Dust bag:1pc
Handle
Speed control
Switch
Dust Outlet
8
6. Installation & Sandpaper Replacement (See following
picture )
Note: Prior to installation or removing the sandpaper, make
sure to not only switch off the device, but also cut off the power
supply.
——Installation Guide
To ensure the replacement procedures, place the device on
the smooth ground prior to installation. Take the sandpaper from
the toolbox, and then fix it onto the disk (see Fig .2). The back of
the sandpaper (Item 1) will automatically glue with the
disk/adhesive disk (Item 2), making both connection and
conduction available.
In order to promote the grinding efficiency, it is necessary to
change the sandpaper after the device has been operational for a
certain period. Firstly, switch off the device and disconnect the
9
socket. Then, remove the previous sandpaper entirely from the
disk, so as to lay new sandpaper neatly as well as facilitate future
replacement. At last, fix new sandpaper in position.
——Sandpaper Overview
Grinding towards the target wall and object is possible with
abrasive grains and sandpaper twisting upon operations. The
sandpaper is classified into various categories according to its
dimensions. It is recommended to select the sandpaper in
accordance with actual size of the disk. The more abrasive grains
included on the sandpaper, the better flatness and parallelism can
be achieved via grinding, while the grinding efficiency will fall
accordingly and vice versa. Therefore, the sandpaper (Ф225mm)
is recommended upon actual needs.
:
Warning ：Prior to the sandpaper replacement or
installation, do read safety precautions and installation guide
carefully.
7．Installation & viscid disc Replacement (See following
picture)
If the viscid disc is damaged in the work, a new viscid disc can be
purchased from our company for replacement.
——Installation Guide
Tabla de contenidos
Otros manuales de Lijadora de Ningbo
