Nilfisk-Advance BA 500 Manual de usuario

Model 66324400 12/94 Form Number 043023

NILFISK BA 500

Service Manual

ORDER PARTS

Online: www.ivie-ent.com

Phone: (918)254-5161

TABLE OF CONTENTS

________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

Batteries .................................................................................................................21

Brush Drive Belt Adjustme t Or Replaceme t .........................................................7

Brush Drive Motor - Carbo brush I spectio ......................................................... 8

Brush Drive Motor Replaceme t ............................................................................. 8

Brush Drive System Mai te a ce ............................................................................7

Brush Drive System Troubleshooti g .....................................................................10

Differe tial Replaceme t ........................................................................................16

Pote tiometer Adjustme t ......................................................................................20

Safety .......................................................................................................................1

Sole oid Valve - Removal / Disassembly & Clea i g ..............................................4

Solutio System Mai te a ce..................................................................................4

Solutio System Troubleshooti g.............................................................................6

Specificatio s & Mai te a ce ..................................................................................2

Squeegee Adjustme t ............................................................................................13

Vacuum Motor Removal .........................................................................................12

Vacuum System Mai te a ce................................................................................11

Vacuum System Troubleshooti g...........................................................................14

Wheel Drive Chai - Replaceme t Or Adjustme t .................................................17

Wheel Drive Motor Replaceme t ...........................................................................17

Wheel Drive System Troubleshooti g ....................................................................18

Note: All refere ces to right, left, fro t, or rear i this ma ual are as see from the operator’s sta d-poi t.

________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

SYMBOLS

Nilfisk uses the symbols below to sig al pote tially da gerous co ditio s. Always read this i formatio

carefully a d take the ecessary steps to protect perso el a d property.

DANGER!

Is used to war of immediate hazards that will cause severe perso al i jury or death.

WARNING!

Is used to call atte tio to a situatio that could cause severe perso al i jury.

CAUTION!

Is used to call atte tio to a situatio that could cause mi or perso al i jury or damage to the machi e or other

property.

________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

GENERAL SAFETY INSTRUCTIONS

WARNING!

Keep sparks, flame a d smoki g materials away from the batteries. Explosive gases are ve ted duri g

ormal operatio .

Remove all jewelry whe worki g ear electrical compo e ts.

Disco ect o e of the battery termi als whe servici g electrical compo e ts.

Never work u der a machi e without safety sta ds or blocks to support the machi e.

CAUTION!

Carefully read all i structio s pertai i g to a service fu ctio before performi g that fu ctio .

Take precautio s to preve t hair, jewelry, or loose clothi g from becomi g caught i movi g parts.

SAFETY

1 BA 500 Service Ma ual

SPECIFICATIONS

________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

SPECIFICATIONS

Dimensions English (Metric)

Scrub Brush Diameter 20 inches (51 cm)

Scrub Brush Path 20 inches (51 cm)

Scrub Brush Pressure 70 lbs (32 kg)

Scrub Brush Speed 190 rpm (190 rpm)

S ueegee Size 25.5 inches (65 cm)

Machine Length 44 inches (112 cm)

Machine Width 21.75 inches (55 cm)

Machine Height 43.5 inches (110 cm)

Drive Wheel 8 inch (20 cm) soft ride wheels

Solution Tank Capacity 12 gal (45i)

Recovery Tank Capacity 12 gal (45i)

Coverage Rate 7,500 s ft (697 m2) per hour

Machine Weight 266 lbs (121 kg) net w/o batteries

558 lbs (253 kg) w/four 244 AH batteries

376 lbs (175 kg) w/two 93 AH batteries

350 lbs (159 kg) shipping weight

General Speci ications

Brush Motor 24 volt, 1/2 hp dc motor

Wheel Drive Motor 24 volt, 1/4 hp dc motor

Vacuum Motor 24 volt, 3/4 hp dc motor

Brush Drive Belt drive

Sound Level 68.2 db (A) @ 3 ft (.9m) using pads

68.9 db (A) using prolene scrub brushes

S ueegee Type 4 sided, curved, pivot type

Speed Control Electronic, fully variable forward/reverse

Batteries (4) 6 volt 244 AH (std)

(2) 12 volt 93 AH (opt)

BA 500 Service Manual 2

________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

MAINTENANCE CHART

Once a Once a Once a

MAINTENANCE ITEM Daily Week Month Year

Clean and inspect the tanks and hoses X

Clean the brushes and pads X

Clean the s ueegee X

Charge the batteries X

Check battery water level X

Lubrication X

Vacuum motor carbon brushes X

MAINTENANCE

3 BA 500 Service Manual

ORDER PARTS

Online: www.ivie-ent.com

Phone: (918)254-5161

SOLUTION SYSTEM

1Remove the vacuum motor. See

Vacuum System chapter for instruc-

tions.

2Disconnect the solution valve and

mercury switch wiring connectors.

3See Figure 1. Remove hoses “A” and

“ ”.

4Remove (2) bolts “C” and remove the

solution valve and bracket from the

machine.

________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

MAINTENANCE

The solution system should be thoroughly flushed once a week. To flush the solution system...

1Empty the solution tank, using the clear plastic drain hose on back of machine. This automatically

flushes loose dirt from solution filter.

2Put clean, warm water into the solution tank and let it drain through the drain hose.

3Put the plug in the drain hose and put about 2 inches of clean water in the solution tank.

4Put the machine controls in the following positions:

• Key Switch - ON

• Solution Switch (on left side of handle) - ON

• rush drive lowered

• Twist Grips - Forward

• Flow control lever (on right side of control handle) UP

• Let all of the clean water flow from the tank. This will flush dirt and soap residue from the electric sole-

noid valve and the flow control valve.

________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

SOLENOID VALVE REMOVAL

C

A

FIGURE 1

Front

BA 500 Service Manual 4

SOLUTION SYSTEM

________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

SOLENOID VALVE DISASSEMBLY AND CLEANING

1Remove the solenoid valve. See the Solenoid Valve Removal section for instructions.

2See Figure 2. Remove the (2) “D” screws and nuts and disassemble the valve (be careful not to lose any

internal parts).

3Thoroughly wash dirt from block “E” and diaphram “F”.

4After reassembling, test the solenoid valve for proper operation.

D

FIGURE 2

EF

5 BA 500 Service Manual

SOLUTION SYSTEM

________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

TROUBLESHOOTING

________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

Probl m: No solution flow

Possibl Caus and R m dy:

1Machine controls not positioned properly. In order for solution to flow, the controls must be positioned as

follows:

• Key Switch - ON

• Solution Switch (on left side of handle) - ON

• rush drive lowered

• Twist Grips - Forward

• Flow control lever (on right side of control handle) UP

2Clogged Solution Filter. Drain solution tank, using the clear plastic drain hose on back of machine. This

automatically flushes loose dirt from solution filter. If solution still does not flow, remove and disassemble

the tee-fitting (under the solution tank), remove and clean the filter thoroughly.

3Clogged Solenoid Valve. Remove, disassemble, and clean the solenoid valve. See the Solenoid Valve

Disassembly and Cleaning section for instructions.

4Defective Speed Control. Replace speed control.

________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

Probl m: Solution leaks in “OFF” position

Possibl Caus and R m dy:

1Dirt in solenoid valve. Remove, disassemble, and clean the solenoid valve. See the Solenoid Valve

Disassembly and Cleaning section for instructions.

2Defective solenoid valve. Replace the solenoid valve. See the Solenoid Valve Removal section for

instructions.

BA 500 Service Manual 6

BRUSH DRIVE SYSTEM

________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

MAINTENANCE

Once every six months

1Check the belt tension, adjust if necessary.

Once a year

1Check the carbon brushes in the brush motor. Replace the brushes if they are worn to a length of 3/8

inch ( 0 mm) or less.

________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

BELT ADJUSTMENT OR REPLACEMENT

1Drain the solution and recovery tanks.

2See Figure . Tip the machine back as

shown and place a jack stand under the

front end.

3See Figure 2. Turn nut “A” counterclockwise to loosen the belt tension.

FIGURE 1

FIGURE 2

4Remove screw “B” and remove the idler assembly and the belt from the machine. Remove “E” bolts, and

remove the belt from the idler.

5Follow steps in reverse order to reassemble. Tighten nut “A” until the tension spring is 2 /2 inches (63.5

mm) long. Test the brush drive system to make sure it operates properly.

AD

E

C

D

C

B

Front

7 BA 500 Service Manual

BRUSH DRIVE SYSTEM

________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

BRUSH DRIVE MOTOR - CARBON BRUSH INSPECTION

1Remove the brush drive motor. See the Brush Drive Motor Replacement section for instructions.

2See Figure 3. Place the brush drive motor in a vice as shown. Be careful not to damage the pulley.

FIGURE 4FIGURE 3

3See Figure 4. Remove (2) “F” nuts and remove the end bell from the motor.

4Remove and measure the carbon brushes. If they are worn to 3/8 inch (9.66 mm) or shorter, replace

both carbon brushes. Remove all loose carbon and dirt from the inside of the motor.

5Follow steps -3 in reverse order to reassemble.

6Test the motor to make sure it operates properly.

________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

BRUSH DRIVE MOTOR REPLACEMENT

1Drain the solution and recovery tanks and remove the solution tank from the machine.

2Tip the recovery tank to the side and disconnect the batteries.

3Remove the vacuum motor. See the Vacuum System section for instructions.

4Disconnect the wires from the brush drive motor. Take note of which wire color goes to each terminal for

reassembly.

FF

BA 500 Service Manual 8

Nilfisk-Advance BA 500 Manual de usuario

Manuales populares de Máquina de piso de otras marcas