Nilfisk-Advance MD421-P Instrucciones de montaje

Software Manual

Control Panel for Pegasus Units

Models: MD421-P

MD422-P

BWP4-P

Software Manual

V. 5.02

110007944-EN

Software Manual_Pegasus.

1. DESCRIPTION 3

2. DISPLAY LAYOUT 4

3. MODES 5

3.1 Power On 5

3.2 Standby 5

3.3 Power o󰀨 6

3.4 Error / Warning 6

4. CONTENT OF MAIN- AND SUBMENUS 7

5. OVERVIEW OF MAIN- AND SUB-MENUS 8

5.1 Content of the Info menu 9

5.2 Content of the Errors menu – CAUSE & REMEDY 9

5.2.1 Error List 9

5.3 Content of the Setup menu 11

5.3.1 Submenu setting 12

5.3.2 Submenu Language & Units 12

5.3.3 Submnenu Installation 12

5.4 Content of Readings 13

6. UPGRADE FIRMWARE 14

6.1 Upgrade using USB Cable 14

6.2 Upgrade using IrDA Cable 16

6.3 Upgrade Controller Board 18

110007944-EN

Software Manual_Pegasus.

1. Description

This software manual describes the operation of the control panel of the Single Booster unit.

The unit is operated via the control panel (see below illustration).

1. OFF

Button (1) switches OFF the unit.

2. ON/STANDBY

Button (2) switches ON the unit.

3. ERROR

Error light indicator (3).

4. NAVIGATION BUTTONS

The four ”arrow” navigation buttons (4)

are used for navigation in the display

menu. Pressing the ”OK” button

 activatesthemenuandconrmsany

activity displayed.

5. DISPLAY

110007944-EN

Software Manual_Pegasus.

2. Display layout

Example:

pressure: 25 bar

Standard

pressure: 25 bar

Standard

ERA +

(1)

When switched on the display will show an arrow symbol in the top right corner equivalent to the

active navigation buttons on the control board.

The arrows illustrate that it is possible to scroll up and down between the menus. Scrolling to the

right makes it possible to enter a value. Set the value scrolling up (+) or down (-) to set the value

higherorloweraccordingly.Conrmbypressingok.

(2)

A letter combination for easy reference in connection with service work will appear in the top right

corner of the display.

(2)

(1)

110007944-EN

Software Manual_Pegasus.

3. Modes

3.1 Power On

Theveryrsttimetheunitisswitchedon,werecommendsettingdateandtimeintheSetup

menu,settings,displayEP.Ifdateandtimeisnotset,dateandtimewillcountfromthepre-set

default date and time.

2006-01-01 12:00

Date & time

Set date and time using navigation buttons.

Set date & time

2006-01-01 12:00

ConrmbypressingOKbutton.

3.2 Standby

The start up display will look as the one below.

Nilfisk

FOOD

Pegasus 12:00:00

110007944-EN

Software Manual_Pegasus.

3.3 Power O

Whentheunitiso󰀨thedisplaywillonlyshowasmalldotinthetoprightcorner.

InO󰀨modeitispossibletoaccessallmenuswithoutthepumprunningbypressingthe

OK button on the panel.

DotisequivalenttotheOKconrmbuttononthepanel.

3.4 Error/Warning

ERROR

WARNING

Incaseofanerror,“ERROR”willappearonthedisplayscreen.

Press the OFF button to switch of unit.

IftheerrorremainswhentheunitisswitchedONagain,pleasePressrightarrowtoseecurrent

error.

Incaseofawarning,“WARNING”willappearonthedisplayscreen.Whenawarningisdetected

the machine will either stop or run with limited performance until the cause of the warning has

been improved (eg. inlet pressure).

To see further error/warning list and possible cause and remedy go to section 5.2.

110007944-EN

Software Manual_Pegasus.

4. Content of Main- and Submenus

The control panel contains the below main menu screen displays.

Scroll between the menus using the navigation buttons.

Each main menu contains submenus which will be described subsequently.

Info

Errors

Setup

Readings

110007944-EN

Software Manual_Pegasus.

5. Overview of Main- and Sub-menus

1. Info (A)

1 Info (AEA)

2. Errors (B)

3. Setup (C) (default password 6802)

1 Password (CA)

2 Settings (E)

Standard pressure (ER)

Autoo󰀨delay(EZ)

Date & Time (EP)

3 Languages & units (F)

Language (FA)

Units (FB)

4 Communication (I)

Firmware Upgrade by cable (IC)

Firmware Upgrade by infrared (ID)

5 Installation (K)

Install Password(KA)

4. Readings (R)

Pump state (RA)

Pump-top pres. (RB)

Pump-top temp (RC)

Supply pressure (RD)

Supply temp. (RE)

Flow Status (RF)

110007944-EN

Software Manual_Pegasus.

5.1 Content of the Info menu

Please note that the Info menu is only for display – all data must be typed in via the setup menu!

Info

INFO

HW ID:PEGASUS

CT ID:

AEA

SW ID: 5.02 5-14

1.01

Thisdisplayviewisonlymentasanexample,SWIDand

CT ID shows the current SW version.

DisplaysSoftwareversionandPumpsize,machine

congurationandcontrollersoftwareversion/ID.

5.2 Content of the Errors menu – CAUSE & REMEDY

Example of Error log screen display:

All error occurrences will be stamped with date and time.

E indicates Error number. P indicates Pump number.

E0\P1

2006-01-01 12:00

C1 Inverter

Error

E0\P1

2006-01-01 12:00

C1 Inverter

Error

Theerrorlogstoresupto1000occurrences.Whenmax.memoryisreached,theerrorswillbe

deleted according to ”First in” First out” principle.

5.2.1 Error List

Error Cause Remedy

C1 Inverter

Error

1. Frequency inverter in error state 1.Switcho󰀨thepowerontheservice

switch. Wait 180 sec. Switch on the unit

again.Iferrorstilloccurs,pleasecontact

your local service technician.

C2 Low Supply

Pressure

1.Insu󰀩cientwatersupply 1.Securesu󰀩cientwatersupplypres-

sure.

2.Checkinletlterforimpurities/rinse

lter

3. Contact your local service technician.

C3 High Water

Temp.

1. Water pump top temperature is above 80°

2. Water consumption is too low (pump column has

been overheated)

1. Lower the inlet water temp. (max

70°C)

2.Securesu󰀩cientwaterconsumption

3. Contact your local service technician.

C4 High Motor

Temp.

1.Insu󰀩cientcoolingofmotor

2. The ambient temperature is above 40°

1. Secure that all air channels are open

and not blocked by impurities

2. Lower ambient temperature

C5 High Supply

Temp.

1. Water inlet temperature is above 70° 1. Lower the water temp. (max 70°C)

2. Contact your local service technician.

110007944-EN

Software Manual_Pegasus.

C6 Low Sensor

Supply Voltage

1. Voltage supply for sensors too low 1.Press“o󰀨”button

2.Iferrorreoccurs,contactyourlocal

service technician.

C7 No Response

Error

1. No communication between display and control

board

1. Contact your local service technician.

C8 Low Tank

Level

1.Insu󰀩cientwatersupply

2. Water supply valve not open

1. Check correct water supply

2.Securesu󰀨cientairsupplytovalve

3. Contact your local service technician.

C9 High Tank

Level

1. Water supply valve not closed 1.Securesu󰀩cientairsupplytothe

valve.

2. Contact your local service technician.

C11 Warning

Cri. Inlet press.

1.Insu󰀩cientwatersupply

2. Booster will return to standby mode after 20 sec.

If this error occurs 3 times within 20 min. Error C2

occurs.

1.Securesu󰀨cientwatersupplyorre-

duce consumption

2.Checkinletlterforimpurities/rinse

lter

3. Contact your local service technician.

C13 Warning

Low inlet press.

1.Insu󰀩cientwatersupply.

Themachinewillkeeponworkingasalways,butthe

maximum speed of the pump will be reduced until suf-

cientinletpressureispresent.

1.Securesu󰀩cientwatersupplyor

reduce consuption

2.Checkineltlterforimpurities/Rinse

lter

C14 Warning

leakage start

1.Boosterstartconditionchangedtoow,dueto

leakage in pipe

1. Check for leakage in pipe system.

2.Press“o󰀨”button

3.Iferrorreoccurs,contactyourlocal

service technician.

C20 Low Sensor

Signal P-Pump-

top

1.Pressuresignalfrompumptopsensor,outofrange 1.Press“o󰀨”button

2.Iferrorreoccurs,contactyourlocal

service technician.

C21 Low Sensor

Signal T-Pump-

top

1.Temparaturesignalfrompumptop,sensor,outof

range

1.Press“o󰀨”button

2.Iferrorreoccurs,contactyourlocal

service technician.

C22 Low Sensor

Signal P-Inlet

1.Pressuresignalforminletsensor,outofrange 1.Press“o󰀨”button

2.Iferrorreoccurs,contactyourlocal

service technician.

C23 Low Sensor

Signal T-Inlet

1.Temperaturesignalfrominletsensor,outofrange 1.Press“o󰀨”button

2.Iferrorreoccurs,contactyourlocal

service technician.

C24 Low Sensor

Signal block

1.Signalfromblocksensor,outofrange 1.Press“o󰀨”button

2.Iferrorreoccurs,contactyourlocal

service technician.

C25 Low Sensor

Signalow

1.Signalfromowsensor,outofrange 1.Press“o󰀨”button

2.Iferrorreoccurs,contactyourlocal

service technician.

C30 High Sensor

Signal P-Puump-

top

1.Pressuresignalfrompumptopsensor,outofrange 1.Press“o󰀨”button

2.Iferrorreoccurs,contactyourlocal

service technician.

C31 High Sensor

Signal T-Pump-

top

1.Temperaturesignalfrompumptopsensor,outof

range

1.Press“o󰀨”button

2.Iferrorreoccurs,contactyourlocal

service technician.

C32 High Sensor

Signal P-Inlet

1.Pressuresignalfrominletsensor,outofrange 1.Press“o󰀨”button

2.Iferrorreoccurs,contactyourlocal

service technician.

C33 High Sensor

Signal T-Inlet

1.Temperaturesignalfrominletsensor,outofrange 1.Press“o󰀨”button

2.Iferrorreoccurs,contactyourlocal

service technician.

Otros manuales para MD421-P

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Panel de control de Nilfisk-Advance

Nilfisk-Advance

Nilfisk-Advance MD421-P Manual de usuario

Manuales populares de Panel de control de otras marcas

RDZ

RDZ PC-HRX Manual de usuario

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manual técnico

Efka

Efka Variocontrol V810 Manual de usuario

Cebora

Cebora 208-10 Manual de usuario

AMX

AMX AutoPatch CP-15 Manual de usuario

Satel

Satel CA-6 KLED-S Manual de usuario

Evolution

Evolution IQ plus 800 Manual de usuario

Fagor

Fagor 8040 TCO CNC Manual de usuario

Trane

Trane ComfortLink II XL950 Control Manual de usuario

AKO

AKO PROCool AKO-17635-2 Manual de usuario

ABB

ABB 6136/30M-101 Manual de usuario

Telikou

Telikou BK-603 Belt Pack Manual de usuario

Mapei

Mapei Mapeheat Thermo Touch Manual de usuario

Bosch

Bosch D9412GV4 Manual de usuario

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manual de usuario

Sminn

Sminn BOX L VF1L EI Manual de usuario

Balboa

Balboa TP600 Manual de usuario

Nice

Nice HSCU1 Especificaciones técnicas