Nikon A1+ Manual
LBIC
Nikon confocal A1+
Standard operating procedure
Version 1.2 June 2019
(1)
Motorized stage
power
Brightfield lamp power
A1 controller
Laser
on/off
key
Laser
buttons
(2)
Turning on/off the system
1. Turn on computer
2. Power on A1 controller and laser
power supply.
3. Turn the key and select the
needed lasers by pressing the
buttons.
4. Turn on stage power supply and
DIA lamp if bright field is needed
5. Power on microscope, wait until
startup sequence is finished.
6. Log in with your LBIC account
and start NIS-Elements AR
7. Turn off system in reverse order
4
(3)
Finding your sample
1. Put your sample in the appropriate holder, if you have slides make
sure the coverslip is facing down.
2. Start with either 10x or 20x objective
3. Navigate to a suitable place in your sample with the joystick.
4. Press “Eye port” to change the light path to the eye piece, if
needed press the Sola button (on Sola pad) to activate the LED
lights.
5. Use the coarse focusing mode and find focus (for slides around Z=
2100-2200, for 30mm petri dishes around Z=2500-2700)
6. Press “Eye port” again to switch to confocal mode (the first time
the system is started do this twice, this is a bug in the software).
2
4
4
(4)
Confocal Acquisition: Quick Start
1. Setup your channel requirements
2. HV (Gain), start at 100 for 405/640 and 25 for 488/561 PMTs
3. Offset adjustment, leave at 0
4. Laser Power, start at 2%
5. Start with a scan size of 512x512 and scan speed of 2.2 µsec.
6. Select “Normal” and “Ch Series” if using more than one laser
7. Select 1.2 AU for Pinhole
8. Start “SCAN”
9. Adjust detector and lasers settings if needed
10. Change pixel size by manually changing zoom factor in A1+ Scan Area” dialog
(View>Acquisition Controls>A1 Scan Area) or pressing Nyquist for optimal pixel
size for the selected objective and pinhole size.
11. Quickly Capture an image with the current settings. Image must be saved
manually afterwards. Save as .nd2.
*If you need to go back to the eyepieces to check your slides, click “Eye Port”,
click it again to return to the confocal!
2-4
1
5
6
7
8
10
11
(5)
Confocal Acquisition: ND Acquisition
Very useful for setting up advanced imaging protocols
1. Enter file save path (O:\is recommended)
2. Combine function tabs as needed by clicking the boxes
•Time is for time lapse videos
•XY saves coordinates (Z can be included with the include Z box)
•XY points carry over with objective change (as long as the sample is not
moved in the holder
•Large image captures multiple fields of view and stitches them to one image
•Very useful for creating maps of your sample with lower resolution (10x or
20x) that can be used to find points of interest and adding to XY (right click
on the point and select ”add this point to ND acquisition”.
•needs at least one XY point to work (this point will be the center point of
the large image).
•Z is used for capturing Z-stacks
•Can be setup by either manually selecting top and bottom Z-values or in
relative mode where the center Z-value is taken from XY (include Z needs
to be selected). The latter is used when you want to capture Z-stacks in
more than 1 XY point.
3. Contextual GUI for each function tab
*XY points can be added also when viewing in the eye port. Useful for quickly
adding points of interest before starting scanning.
1
2
3
(6)
(7)
(8)
(9)
Z-focus adjustment
Joystick
Changing sample holder
(10)
1
2
The confocal sample holders:
1. Multi-holder (slides and small petri dishes)
2. Multiwell plate holder (for all standard multiwell plates)
3. Oko-labs stage top incubator (see next page) with fittings for two 35mm petri dishes and
one 75mm x 25mm slide (standard slides and chamber slides)
Exchanging between them is simple
1. Remove plastic screws with
screwdriver located on top of
shelf.
2. Remove holder and put on shelf.
3. Change to the desired sample
holder (they only fit one way)
4. Fasten plastic screws gently.
DO NOT OVER TIGHTEN! The
screws break quite easily.
5. Put back screwdriver on shelf.
Otros manuales para A1+
1
Tabla de contenidos
Otros manuales de Microscopio de Nikon
Nikon
Nikon Eclipse L200A Manual de usuario
Nikon
Nikon SMZ-10 Instrucciones de funcionamiento
Nikon
Nikon SMZ745T Manual de usuario
Nikon
Nikon 50i Manual de usuario
Nikon
Nikon Optiphot Instrucciones de funcionamiento
Nikon
Nikon SMZ1000 Manual de usuario
Nikon
Nikon ECLIPSE Ni-E Manual de usuario
Nikon
Nikon 50i Manual de usuario
Nikon
Nikon Eclipse LV100DA-U Manual de usuario
Nikon
Nikon Eclipse L200 Manual de usuario
Nikon
Nikon Ee1078 Manual de usuario
Nikon
Nikon Eclipse 800 Manual de usuario
Nikon
Nikon ECLIPSE Ti2-U Manual de usuario
Nikon
Nikon OPTIPHOT-2 Manual de usuario
Nikon
Nikon LABOPHOT-POL Manual de usuario
Nikon
Nikon Live Cell 2 Manual de usuario
Nikon
Nikon 50i Manual de usuario
Nikon
Nikon Optiphot 66 Manual de usuario
Nikon
Nikon ECLIPSE L200ND / ECLIPSE L200N Manual de usuario
Nikon
Nikon Eclipse E600 Manual de usuario
