Night Optics TM-X Manual de usuario
NIGHT OPTICS USA, INC | www.nightoptics.com
Multi-Function Thermal Camera
Operator Manual
TABLE OF CONTENTS
Package Contents 2
Product Overview 2
Products Specifications 3
System Controls 4
Cables 4-5
Power Management 5-6
Battery Installation
Battery Status
Battery Charging Method
Operation 6-11
Menu Mode
Media Playback
Formatting SD Card
Restore Factory Setting
Features
Image/Video Capture
Polarity
Digital Zoom
Storage & Maintenance 12
Troubleshooting 13
Warranty 14
NOTE: Please read this operators manual thoroughly before using
your device.
2
NIGHT OPTICS USA THERMAL IMAGING
PRODUCT OVERVIEW
[1] Eyepiece
[2] Controls
[3] Device Body
[4] Hand Strap Interface
[5] 25mm Objective
[6] Focus Ring
[7] Interface Port
[8] Battery Compartment
[9] SD Card Port
[10] Proximity Sensor
[11] Battery Door
[12] Diopter Focus Adjustment
3
5
4
1
2
78
10
9
11 12
6
PACKAGE CONTENTS
■ TM-X Thermal Monocular
■ Interface Cable
■ (1) Set Rechargeable Batteries
■ Battery Charger
■ 12v DC Car Power Cable
■ 4gb SD Card
■ Lens Cover
■ Hand Strap
■ Carrying Case
■ Operator Manual
Figure 1
3
NIGHT OPTICS USA THERMAL IMAGING
TECHNICAL SPECIFICATIONS
Type & Material Uncooled ASI FPA
Resolution 160x120
Spectral Response 8-14 µm
NETD <= 120mK
Pitch 25 µm
Contrast / Brightness Full Auto / Semi-Auto / Manual
Lens System 25mm f1.0
Polarity Black Hot / White Hot
Field of View 9.15° x 6.87°
Refresh Rate 50hz
Magnification 1x Standard / 2x Digital
Range of Focus 5m to ∞
Focus Method Manual
Video Output Format NTSC
Viewfinder Display OLED
Interface Options USB / RCA / Serial
Power Source (4) AA batteries / 9v DC
UpTime 2 hr
Removable storage SD Card
Image Format Bitmap | 320x240
Video Format AVI | 320x240
Detection Range 500 yds
Operating Temperature -4°F - 122°F
Dimensions 182mm x 97mm x 68mm
Weight 16.6oz
Warranty 2 Year
4
NIGHT OPTICS USA THERMAL IMAGING
SYSTEM CONTROLS
CABLES
M
P
1 2 3 4
Figure 2
Functions
Power: Press/Hold for 5 sec. to power on/off the device
Manual Calibration: Momentary press to manually calibrate the device.
Menu Mode: Press this button to highlight menu options - left to right.
Image Capture: Momentary Press to capture and save photos.
Video Capture: Press/Hold for 2 sec. to capture and save video.
[1]
[2]
[3]
[4]
Menu: Press/Hold for 3 sec to bring up menu mode.
Polarity: Momentary press to switch between white/black hot.
Menu Mode:Press this button to select the menu items
Menu Mode: Press this button to highlight menu options - left to right.
Zoom Mode: Switch between 1x and 2x zoom mode.
RS232
PC Interface
USB
Video Out
Power
Device Interface Port Device Interface Cable
Device Output
5
NIGHT OPTICS USA THERMAL IMAGING
CABLES
POWER MANAGEMENT
Figure 4
1. Insert the device interface cable (fig. 3) into the device interface port (fig. 1-7).
2. To remove the device interface cable, pull back on the finger grip to release the
clamping mechanism.
3. The RS232 PC Interface cable is for internal Night Optics USA use only.
4. The USB cable can be connected to any Microsoft Windows™ based computer to
access the contents of the SD Card. When connected the device controls will not
function.
5. The Video out cable (RCA Jack) can be connected to any TV or Monitor that accepts
video input. Video display is in NTSC format only.
6. The 9v DC cable can be used to power the device externally.
Battery Installation
For optimal battery performance it is recommended that 2500 mAh or higher NiMH
rechargeable batteries or standard non-rechargeable Lithium batteries are used. It is not
recommended to mix batteries. To install batteries into your device, open the battery door
(fig. 1-8 & 11) and follow the polarity diagram inside the battery compartment to properly
install batteries. Once installation is complete, ensure the battery door is closed
completely before powering on the device.
Battery Status
The battery status indicator can be found in the upper-left corner of the display when
looking through the eyepiece (fig. 1-1). Battery power level should display as follows:
Battery Charging
Full 75% 50% 25% 0%
NOTE:
For optimal battery life and performance, it is recommended that you fully
discharge the rechargeable batteries before charging for the first time. On
the initial charge, allow to charge fully. This should take 4-6 hours.
POWER MANAGEMENT
OPERATION
6
NIGHT OPTICS USA THERMAL IMAGING
Battery Charging
A battery charger, rechargeable batteries and all necessary cables have been provided as
part of your kit. Please read the following carefully to ensure proper use.
1. Install the batteries into the charger according the diagram on the charger.
2. Connect the appropriate wire for wall charging or car charging
3. An LCD screen will indicate proper installation by displaying an icon of the battery
charging.
4. Once the batteries are charged the unit will shut itself off to avoid damage to the unit or
to the batteries.
WARNING:
1. Do not attempt to recharge batteries while inside the Thermal device.
2. Do not attempt to recharge non-rechargeable batteries.
3. Properly dispose of bloated, deformed, corroded or leaking batteries.
4. Always use the correct cables with the charging unit.
Menu Mode
After start-up, press/hold the “M” button (fig. 2-1), the menu bar will appear with a
loading indicator on the screen. Press the “+” & “-” buttons (fig. 2-3 & 4) to navigate the
menu. Press the “M” (fig. 2-1) button momentarily to select the menu item.
Menu display loading Menu display - Lower 3rd of screen
7
NIGHT OPTICS USA THERMAL IMAGING
OPERATION
Help Menu
In menu mode scroll to the menu option “Help” and press the “M” button to select the
Help Menu. Press the “+” & “-” buttons to navigate the Help Menu. Press “M” to exit the
Help Menu.
Button Layout Menu (Note)
Scroll to the menu option “Note” and press the “M” button to turn icon display on the right
side of the screen “On or Off.” This mode also activates on-screen instructions.
Image Adjustment Menu - Auto/Semi-auto mode setting
In menu mode scroll to the menu option “Auto/Semi Auto/Manual” and press “M” to
switch between Auto, Semi-auto and manual Brightness and contrast control mode
In the above table shows how much control the user will have over Brightness (G) (Gain)
and Contrast (O) (Offset).
Brightness and Contrast Adjustment
In automatic mode, the device will automatically determine the appropriate Brightness (G)
(Gain) and Contrast (O) (Offset) for the best possible image display.
In semiautomatic mode, the user can adjust image brightness (G) (Gain). The device will
automatically set image contrast (O) (Offset) as per your brightness input.
In manual mode, the user has full control over brightness (G) (Gain) and contrast (O)
(Offset).
Contrast option selected Contrast Adjustment to add depth
Mode Menu content Effect
Auto Brightness, Contrast Auto offset and gain
Semi-auto Brightness, Contrast Auto offset, manual gain
Manual Brightness, Contrast Full user control
8
NIGHT OPTICS USA THERMAL IMAGING
OPERATION
Image & Video Playback Menu (Replay)
In menu mode scroll to the menu option “Replay” and press the “M” button. Follow the
on-screen instructions to navigate between images and video content stored on the SD
Card (fig. 1-9), play and/or delete. See examples below
Playback (Step 1) Playback (Step 2)
Playback (Step 3)
Playback (Step 5)
Playback (Step 4)
Formatting the SD Card (Format)
In menu mode scroll to the menu option “Format” and press the “M” button. You will be
prompted with a dialogue box. Follow the on-screen instructions. You have the option to
exit this feature or confirm that you would like to continue formatting the SD Card. Once
the process is complete the dialogue box will confirm a successful reformat, at which
point you can you follow the on-screen instruction to exit.
Standby Menu
Standby mode operates using an IR based proximity sensor (fig. 1-10) located next to the
eyepiece (fig. 1-1). When not in use for the selected period of time the unit will automati-
cally shut itself down. Bringing the unit back up to your eye will reactivate. The longer the
unit remains in standby mode the longer it should take to power back on. In menu mode
scroll to the menu option “Standby” and press the “M” button. You can select 5 mode
options. 4 minutes; 10 minutes; 15 minutes; 20 minutes; Off (Default).
Default Menu (Device Reset)
In menu mode scroll to the menu option “Default” and press the “M” button. You will be
prompted with a dialogue box. Follow the on-screen instructions. You have the option to
exit this feature or confirm that you would like to continue to reset the unit to factory
settings.
9
NIGHT OPTICS USA THERMAL IMAGING
OPERATION
WARNING:
Using this feature will reset all device settings. Upon confirmation, the unit
and all settings will be restored to the original factory setting. Make notes
of specific settings that you like so that you can restore them later.
Tabla de contenidos
Otros manuales de Cámara térmica de Night Optics
