Nice Titan 912L Manual de usuario

Nice

Titan

912L

Vehicular Swing Gate Operator

Revision 5.1.0.0_6-2017

Gate

Operators

The Titan 912L Gate Operator is intended for use with vehicular swing

gates. The Titan 912L Gate Operator can be used in Class I, Class II and

Class III applications.

Part# 10001700

This page intentionally left blank.

TABLE OF CONTENTS

CAUTIONS AND NOTES 1

EXTREMELY IMPORTANT 1

DEFINITIONS COMPLIANT TO UL325 1

1- OVERVIEW 1

1.1 - Titan Swing Gate Opener

1.2 - Titan Swing Gate Opener Speciﬁcations

2 - GATE INFORMATION 1

2.1 - ASTM F2200

2.2 - Gate latches

2.3 - Speciﬁc applications

2.4 - Swing gates

2.5 - General requirements

3 - SAFETY AND CAUTIONS 2

3.1 - Properly installed safety devices

3.2 - Safety signs, notices to personnel warning signs

3.3 - Gate system safety devices

3.4 - Infrared beams and warning signs

3.5 - Establish the location

3.6 - Read and follow all instructions

3.7 - Keep children away

3.8 - Test the gate system

3.9 - Keep gates properly maintained

4 - PRE-INSTALLATION NOTES 3

4.1 - Follow instructions

4.2 - Intended usage

4.3 - Warnings, cautions and notes

5 - INSTALLATION PROCEDURES 5

5.1 - Pivot arm installation

Fig ure 5 - 1 P ULL T O O P EN INS TAL LATIO N

Fig ure 5 - 2 V ER TICAL P IV O T P O S ITIO N

5.2 - Push to open installation

Fig ure 5 - 3 P US H TO O P EN INS TALLATIO N

5.3 - Actuator mounting

F igu re 5 - 4 A CTUATO R MO UNTIN G

F igu re 5 - 5 G A TE B RACKET M O UNTING

5.4 - Manual release/manual operation

F igu re 5 - 6 M ANUAL REL EA S E D IS EN G AG E

F igu re 5 - 7 M AUAL REL EA S E R E- ENG AG E

5.5 - Titan actuator wiring

Fig u re 5 - 8 MAUAL RELEASE HANDLE

Fig ure 5 - 9 WIRE H AR NES S IN S ERTIO N

Fig u re 5 - 10 TITAN ACTUATO R WIRING

5.6 - Control board wiring

F igu re 5 - 11 WIRING D IA G RAM F O R 10 5 0 CO NT RO L BO ARD

F igu re 5 - 12 WIRING D IA G RAM F O R 9 3 6 CO NT RO L BO ARD

5.7 - Limit switch adjustment

F igure 5- 13 LIM IT SWIT C H A D JUST M E N T

F igu re 5 - 14 LIMIT L ED LO CATIO N 10 5 0 C O NT R O L BO ARD

F igu re 5 - 15 LIMIT L ED LO CATIO N 9 3 6 C O NT R O L BO ARD

6 - GENERAL LAYOUT AND SAFETY ACCESS 11

F igu re 6 - 1 L AY O UT F O R IN - G RO UND L O O P S

F igu re 6 - 2 L AY O UT F O R P H O TO CEL LS

7 - ACCESSORIES AND SENSORS 12

8 - INSPECTION AND OPERATION 13

9 - EMERGENCY VEHICLE ACCESS 13

• Vehicular Swing-Gate Operator (or system) - A vehicular

gate operator (or system) that controls a gate which swings

or rotates in a direction that is intended for use for vehicular

entrance or exit to a drive, parking lot, or the like.

• Gate - A moving barrier such as a Swinging, sliding, raising,

lowering, rolling, or like barrier that is a stand-alone passage

barrier or is that portion of a wall or fence system that

controls entrance and/or egress by persons or vehicles and

completes the perimeter of a defined area.

• Residential Vehicular Gate Operator - Class I - A vehicular

gate operator (or system) intended for use in a home of one

to four single family dwellings, or a garage or parking area

associated therewith.

• Commercial / General Access Vehicular Gate Operator -

Class II - A vehicular gate operator (or system) intended for

use in a commercial location or building such as a multi-

family housing unit (five or more single family units), hotel,

garages, retail store, or other buildings servicing the general

public.

• Commercial / General Access Vehicular Gate Operator -

Class III - A vehicular gate operator (or system) intended for

use in an industrial location, loading dock area, or other

location not intended to service the general public.

912L

The Titan 912L swing gate operator delivers the next generation of

easily installed, configured and maintained swing gate operators

from Nice. With a maximum gate capacity of 600 lbs and 20 ft,

this operator has a key lockable manual release, easily accessible

limit switch settings as well as simple in-the-field maintenance and

repair. The Titan gives dealers, installers and homeowners the

ability to take control of their access and security systems. This

operator includes a 2-year factory warranty against manufacturing

defects and lifetime customer support.

operator

2.2 - Gate latches

2.4 - Swing gates

and slide g control

point to or

or slide

autono

periodic schedule.

2.5 - General requirements

countless

AUTOMATIC GATES ARE

NOT FOR PEDESTRIANS!

3 - SAFETY AND CAUTIONS

WARNING

IMPORTANT SAFETY INSTRUCTIONS

WARNING - TO REDUCE THE RISK OF INJURY OR DEATH READ AND

FOLLOW ALL INSTRUCTIONS.

3.1 - Properly installed safety devices

3.2 - Safety signs, notices to personnel warning signs

danger posed

tlashing lamp that is

acti te tim

This swing gate actuator is intended for those locations where vehicle traf-

(gate). The Titan 912L actuator is only to be used in conjunction with Nice

brand control boards. If the gate, actuator and control system are not fully

closed off from public access, the opening and closing of the gate system

may result in severe damage, injury or death.

In association with this gate actuator and this (these ) swing gate(s), at no

time should manual gate latches or locks be used. The forces applied to a

swing gate by the actuator could be in excess to those forces which are safe

for bystanders. Should unnecessary forces be applied to a gate system,

such as a manual lock or impediment, catastrophic failure of the gate,

actuator or control system could result in substantial damage, extensive

physical injury or death.

for vehicular traffic. They are powerful and

safety, security and longevity throughout the life of the system.

required for that specific installation. Care should always be used during

installation!

qualified service person make repairs to gate hardware.

main

them regu

application.

4.1 - Follow Instructions

4.2 - Intended usage

4.3 - Warnings, cautions and notes

can

incorporated in all installations.

tions.

and shoul

3.3 - Gate system safety devices

3.4 - Infrared beams and warning signs

3.5 - Establish the location

3.6 - Read and follow all instructions

3.7 - Keep children away

3.8 - Test the gate system

release.

3.9 - Keep gates properly maintained

technicians are not recommended.

4 - PRE-INSTALLATION NOTES

the application.

operator.

gate operation.

reach through gate

THIS ACTUATOR IS INTENDED FOR USE WITH VEHICULAR

SWING GATES ONLY, WHEN COMBINED WITH A NICE BRAND

CONTROL BOARD.

for these warnings, cautions and notes are intended to

an automatic gate system is installed.

4.3.53 All gate systems must utilize a monitored contact or non-contact

presence detection sensor.

4.3.55 Hardwired contact or non-contact sensors to signal the gate

actuator of entrapment conditions are recommended.

5 - INSTALLATION PROCEDURES

OVERHEAD VIEW

FIGURE 5 - 1 PULL TO OPEN INSTALLATION

FIGURE 5 - 2 VERTICAL PIVOT POSITION

VERTICAL POSITION OF PIVOT ARM

SIDE VIEW

The top edge of the Pivot Arm will be located 1/2”

below the center line for the gate bracket. The Pivot

Arm must be level when secured.

NOTE If you have columns built around

your gate hinge post, check these

measurements for proper clearance

before proceeding with this pull to

open installation.

5.1 - Pivot Arm Installation

IMPORTANT - Never weld parts to the gate or posts when the operator circuit board is powered. Doing so may

damage the board beyond repair.

PULL TO OPEN INSTALLATION - PIVOT ARM INSTALLATION - Location of Pivot Point

The following instructions provide up to 105° of swing.

Measurements are taken from the center of pivot of the gate hinge.

The pivot arm needs to be securely mounted to the hinge post or equivalent mounting surface. It is recommended to weld

the pivot arm to a metal post. In order to achieve the correct articulation, geometry and rate of speed of the gate it is

critical that the measurements below are followed. The pivot arm may need to be cut to achieve the correct placement of

the actuator mounting hole. Measurements are taken from the center of pivot of the gate hinge.

Center line of

attachment point

for gate bracket

Hinge Post

5.2 - Push to open installation

PIVOT ARM INSTALLATION - Location of Pivot Point

Measurements are taken from the center of pivot of the gate hinge.

The pivot arm needs to be securely mounted to the hinge post or equivalent mounting surface. It is recommended

to weld the pivot arm to a metal post. In order to achieve the correct articulation, geometry and rate of speed of the

gate it is critical that the measurements below are followed. The pivot arm may need to be cut to achieve the correct

placement of the actuator mounting hole. Measurements are taken from the center of pivot of the gate hinge.

DIRECTION OF OPENING

GATES CLOSED

HINGE POST HINGE POST

LEFT HAND SWING RIGHT HAND SWING

TOP VIEW

6”

11”

6”

11”

5.3 - Actuator mounting

Mount the actuator to the pivot arm as shown.

Please notice the washer goes below the actuator

The lock nut should be tight to prevent movement or

shifting when the actuator is running. This will also

prevent excessive “bounce” or “wobble” when the gate

stops moving.

FIGURE 5 - 3 PUSH TO OPEN INSTALLATION

FIGURE 5 - 4 ACTUATOR MOUNTING

FIGURE 5 - 5 GATE BRACKET MOUNTING

Manual Release In

Engaged Position

RUBBER

KEY

COVER

5.4 - Manual release/manual operation

1. Close handle

2. Rotate key 90° counterclock wise

and remove key.

3. Replace rubber key cover.

4. Operator is now in re-engaged in

Automatic Mode (manual

operation is not possible).

Manual Release Re-engage

FIGURE 5-7 MANUAL RELEASE RE-ENGAGE

1. Lift rubber key cover and insert

key into lock and rotate 90°

clockwise.

2. Lift handle

3. Actuator is now Disengaged

(manual operation is possible).

Manual Release Disengage

Manual Release in

Disengaged Position 90°

FIGURE 5-6 MANUAL RELEASE DISENGAGE

Otros manuales para Titan 912L

Tabla de contenidos

Otros manuales de Abridor de puerta de Nice

Nice

Nice HySecurity SwingSmart CNX Series Guía de configuración

Nice

Nice WG4024 Manual de usuario

Nice

Nice HYPPO HY 7005 Manual del instalador

Nice

Nice SLH400 Especificaciones técnicas

Nice

Nice MhouseKit WG2W Especificaciones técnicas

Nice

Nice BIG METRO Especificaciones técnicas

Nice

Nice hyke HK7024 Especificaciones técnicas

Nice

Nice MhouseKit WI1 Especificaciones técnicas

Nice

Nice Naked Sliding NKSL400 Especificaciones técnicas

Nice

Nice MhouseKit SL1W Especificaciones técnicas

Nice

Nice Naked Sliding NKSL400 Especificaciones técnicas

Nice

Nice Thor1500Kit Especificaciones técnicas

Nice

Nice RUN1800 Manual del producto

Nice

Nice hyke HK7224 Especificaciones técnicas

Nice

Nice MhouseKit WG20S Especificaciones técnicas

Nice

Nice BOOMKIT4 Manual de usuario

Nice

Nice RS 500 AC Manual de usuario

Nice

Nice Wingo4024 Especificaciones técnicas

Nice

Nice TTN3724RHS Manual de usuario

Nice

Nice hyke HK7024 Manual de usuario

Nice

Nice TITAN12L Manual de usuario

Nice

Nice ROX Series Especificaciones técnicas

Nice

Nice SFAB2024 Especificaciones técnicas

Nice

Nice Mighty Mule MM271 Manual de usuario

Manuales populares de Abridor de puerta de otras marcas

Elite

Elite CSW200UL Manual de usuario

CAME

CAME FROG-PM4 Manual de usuario

SOMFY

SOMFY FX230 Manual de usuario

Aprimatic

Aprimatic ONDA 500 Manual de usuario

Turnstiles

Turnstiles FSW 900 Manual de usuario

Erreka

Erreka BUL BL33 Instrucciones de funcionamiento

Erreka

Erreka VULCAN S Manual de usuario

Beninca

Beninca R1-2 WBV Manual de usuario

Erreka

Erreka VULCAN D Manual de usuario

Motorline professional

Motorline professional FORT Manual de instrucciones

Beninca

Beninca BOB5024 Manual de usuario

AGA

AGA GATEMASTER 900 HD Manual de usuario

Chamberlain

Chamberlain MotorLift HC280ML Manual de usuario

SOMFY

SOMFY Dexxo RTS Pro Manual de usuario

Cardin

Cardin BL Series Manual de usuario

Westfalia

Westfalia 85 27 06 Manual de usuario

CAME

CAME F500 Manual de usuario

Extel

Extel VERA Manual de usuario