Nibe F2050 Guía del usuario

Installer manual

Air/water heat pump

NIBE F2050 UK 1x230V

IHB EN 2220-1

631412

41 Important information

4Safety information

4Symbols

4Marking

4Serial number

5Country specific information

6Inspection of the installation

Compatible indoor modules (VVM) and control

modules (SMO)

7Indoor modules

7Control modules

82 Delivery and handling

8Transport

8Assembly

10Condensation

11Supplied components

12Dismantling panels

133 The heat pump design

13General

17Electrical connection

19Sensor placement

224 Pipe connections

22General

23Symbol key

23Pipe coupling heating medium circuit

24Installation alternative

255 Electrical connections

25General

25Accessibility, electrical connection

26Connections

316 Commissioning and adjusting

31Preparations

31Filling and venting

31Compressor heater

32Start-up and inspection

32Readjusting, heating medium side

32Adjustment, charge flow

337 Control – Heat pump EB101

33S-series – VVM S / SMO S

34F-series – VVM / SMO

358 Service

35Temperature sensor data

369 Servicing and maintenance

36Important

36General inspection

36Heating System

3710 Disturbances in comfort

37Troubleshooting

38Alarm list

4011 Accessories

4112 Technical data

41Dimensions

42Sound levels

43Technical specifications

46Energy labelling

49Electrical circuit diagram

53Item register

59Contact information

3Table of ContentsNIBE F2050

Table of Contents

Safety information

This manual describes installation and service procedures

for implementation by specialists.

The manual must be left with the customer.

Symbols

Explanation of symbols that may be present in this manual.

NOTE

This symbol indicates danger to person or machine.

Caution

This symbol indicates important information about

what you should consider when installing or servi-

cing the installation.

TIP

This symbol indicates tips on how to facilitate us-

ing the product.

Marking

Explanation of symbols that may be present on the product’s

label(s).

Fire hazard!

Read the User Manual.

Read the Installer Manual.

Serial number

The serial number for F2050 can be found on the side of the

foot.

DATA

Caution

You need the product's (14 digit) serial number for

servicing and support.

NIBE F2050Chapter 1 | Important information4

Important information

Country specific information

UNITED KINGDOM

This installation is subject to building regulation approval,

notify the local Authority of intention to install.

Use only manufacturer’s recommended replacement parts.

For more information see nibe.co.uk.

Benchmark places responsibilities on both manufacturers

and installers. The purpose is to ensure that customers are

provided with the correct equipment for their needs, that it

is installed, commissioned and serviced in accordance with

the manufacturers instructions by competent persons and

that it meets the requirements of the appropriate Building

Regulations. The Benchmark Checklist can be used to

demonstrate compliance with Building Regulations and

should be provided to the customer for future reference.

Installers are required to carry out the installation, commis-

sioning and servicing work in accordance with the Bench-

mark Code of practice which is available from the Heating

and Hotwater Industry Council who manage and promote

the Scheme. Visit centralheating.co.uk for information.

Warranty and insurance information

Thank you for installing a new NIBE heat pump in your home.

NIBE heat pumps are manufactured in Sweden to the very

highest standard so we are pleased to offer our customers

a comprehensive guarantee.

The product is guaranteed for 24 months for parts and la-

bour from the date of installation or 33 months from the

date of manufacture, whichever is the shorter.

The NIBE guarantee is based on the unit being installed and

commissioned by a NIBE accredited installer, serviced every

year and the Benchmark documents completed. Where this

condition is not met, any chargeable spare parts or compon-

ents issued within the applicable guarantee period still be-

nefit from a 12 month warranty from the date of issue by

the manufacturer.

We recommend the installer completes and returns as soon

as possible, your guarantee registration card or completes

the guarantee form on the NIBE website www.nibe.co.uk

Electrical Supply

The heat pump must be permanently connected to a 230 V

~ 50 Hz supply.

All system components shall be of an approved type and all

wiring to current I.E.E wiring regulations.

External wiring must be correctly earthed, polarised and in

accordance with the relevant standards: Currently this is

BS 7671.

Heating System

The installation of the heat pump should follow best practice

as covered in the following:

BS 5449 Forced circulation hot water central heating sys-

tems for domestic premises.

BS 15450 Heating systems in buildings – Design of heat

pump heating systems.

5Chapter 1 | Important informationNIBE F2050

Inspection of the installation

Current regulations require the heating installation to be inspected before it is commissioned. The inspection must be

carried out by a suitably qualified person. Fill in the page for information about installation data in the User manual.

DateSignatureNotesDescription

✔

Heating medium (page 23)

System flushed

System vented

Particle filter

Shut-off and drain valve

Charge flow set

Electricity (page 25)

Fuses property

Safety breaker

Earth circuit-breaker

Heating cable type/effect

Fuse size, heating cable (F3)

Communication cable connected

F2050 addressed (only when cascade connec-

tion)

Connections

Main voltage

Phase voltage

When installing F2050-6, check that the

software version of the indoor module/control

module is at least v8320.

Miscellaneous

Warranty

Benchmark checklist

NIBE F2050Chapter 1 | Important information6

Compatible indoor modules (VVM) and control modules (SMO)

SMO S40VVM S320

XXF2050-6

XXF2050-10

SMO 40SMO 20VVM 225

XXXF2050-6

XXXF2050-10

Indoor modules

VVM S320

Stainless steel, 1x230 V

With T&P valve

Part no. 069 199

VVM 225

Stainless steel, 1x230 V

With T&P valve

Part no. 069 232

Control modules

SMO S40

Control module

Part no. 067 654

SMO 20

Control module

Part no. 067 224

SMO 40

Control module

Part no. 067 225

7Chapter 1 | Important informationNIBE F2050

Transport

F2050 must be transported and stored vertically.

NOTE

Ensure that the heat pump cannot fall over during

transport.

Check that F2050 has not been damaged during transport.

LIFT FROM THE STREET TO THE SET UP

LOCATION

If the surface allows, the easiest method is to use a pallet

truck to move the heat pump to the installation area.

If the heat pump needs to be transported across soft ground,

such as a lawn, we recommend using a crane truck that can

lift it to the installation location. When the heat pump is lifted

with a crane, the packaging must be intact.

If a crane truck cannot be used, the heat pump can be

transported on an extended sack truck. The heat pump must

be taken hold of from its heaviest side and two people are

required to lift it.

LIFT FROM THE PALLET TO FINAL POSITIONING

Before lifting remove the packaging and the securing strap

to the pallet.

Place lifting straps around each foot. It is recommended

that two people perform the lift from the pallet to the base.

SCRAPPING

When scrapping, remove the heat pump in reverse order. In

this case, lift by the base plate rather than the pallet!

Assembly

•Place the heat pump in a suitable location outdoors to

prevent any risk of the refrigerant flowing in through

ventilation openings, doors or similar openings in the event

of a leak. It must also not constitute a hazard to people or

property in any other way.

•If the heat pump is placed in a location where any refriger-

ant leak could accumulate, for example below ground level

(in a dip or low-lying recess), the installation must satisfy

the same requirements that apply for gas detection and

the ventilation of engineering rooms. Requirements regard-

ing sources of ignition must be applied where appropriate.

•Place F2050 outdoors on a solid level base that can take

the weight, preferably a concrete foundation. If concrete

slabs are used they must rest on asphalt or shingle.

•The lower edge of the evaporator must not be lower than

the level of the average local snow depth, or at least 300

mm above ground level. The base should be at least 70

mm tall.

•F2050 should not be positioned next to noise sensitive

walls, for example, next to a bedroom.

•Also ensure that the placement does not inconvenience

the neighbours.

•F2050 must not be placed so that recirculation of the

outdoor air is possible. Recirculation entails reduced power

and impaired efficiency.

•The evaporator must be sheltered from direct wind / ,

which negatively affects the defrosting function. Place

F2050 protected from wind / against the evaporator.

•Large amounts of condensation, as well as melt water

from defrosting, may be produced. Condensation must

be led off to a drain or similar (see section “Condensation

water").

•Care must be exercised so that the heat pump is not

scratched during installation.

LEK

Cirka 1 m

LEK

Cirka 1 m

min 300 mm

Min. 300 mm

Do not place F2050 directly on the lawn or other non solid

surface.

NIBE F2050Chapter 2 | Delivery and handling8

Delivery and handling

If there is a risk of snow slip from roof, a protective roof or

cover must be erected to protect the heat pump, pipes and

wiring.

9Chapter 2 | Delivery and handlingNIBE F2050

INSTALLATION AREA

The distance between F2050 and the house wall must be at least 150 mm. The free space above F2050 must be at least

1,000 mm. The free space in front must be at least 1,000 mm for future servicing.

255

Ställbar 40-50 955

243

512

110

395

265

452 1075

1145

108

Ø40*

150 mm

Fritt utrymme bakom

Min. avstånd

vid användning

av ﬂera F2040

600 mm

3000 mm

400 mm 600 mm

Minimalt

fritt utrymme

Minimalt

fritt utrymme

Fritt utrymme

framför

Free space behind

Min. distance when using

several F2050

Free space Free space

Free space in

front

1000 mm

Condensation

The condensate drain pan collects and leads away the con-

densation water.

NOTE

It is important to the heat pump function that

condensation water is led away and that the drain

for the condensation water run off is not posi-

tioned so that it can cause damage to the house.

Condensation run-off should be checked regularly,

especially during the autumn. Clean if necessary.

•The condensation water (up to 50 litres / 24 hrs) must be

routed away by a pipe to an appropriate drain, it is recom-

mended that the shortest outdoor length possible is used.

•The section of the pipe that can be affected by frost must

be heated by the heating cable to prevent freezing.

TIP

Pipe with heating cable for draining the condens-

ation water trough is not included.

•Route the pipe downward from the heat pump.

•The outlet of the condensation water pipe must be at frost

free depth.

•Use a water trap for installations where air circulation may

occur in the condensation water pipe.

•The insulation must seal against the bottom of the con-

densation water trough.

DRAIN PAN HEATER, CONTROL

The drain pan heater is supplied with power when one of

the following conditions is met:

1. The compressor has been in operation for at least 30

minutes after last start.

2. The ambient temperature is lower than 1 °C.

DRAINAGE OF CONDENSATION

Stone caisson

LEK

Frostfritt djup

Frost proof

depth

If the house has a cellar the stone caisson must be posi-

tioned so that condensation water does not affect the house.

Otherwise the stone caisson can be positioned directly under

the heat pump.

NIBE F2050Chapter 2 | Delivery and handling10

Otros manuales para F2050

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Bomba de calor de Nibe

Nibe

Nibe F1245 Manual de usuario

Nibe

Nibe F750 Instrucciones de funcionamiento

Nibe

Nibe VST 11 Manual de usuario

Nibe

Nibe F2040 Series Manual de usuario

Nibe

Nibe F750 Guía del usuario

Nibe

Nibe FIGHTER 360P Manual de usuario

Nibe

Nibe F1345 Series Guía del usuario

Nibe

Nibe S1155 Guía del usuario

Nibe

Nibe F130 Guía del usuario

Nibe

Nibe CLIMATEMASTER TRT Series Manual del propietario

Nibe

Nibe F130 Manual de usuario

Nibe

Nibe F1155 Series Manual de usuario

Nibe

Nibe FIGHTER 640P Manual de usuario

Nibe

Nibe F750 Manual de usuario

Nibe

Nibe F1126 Manual de usuario

Nibe

Nibe F1345 Series Manual de usuario

Nibe

Nibe F1155 Series Manual de usuario

Nibe

Nibe SPLIT AMS 10 Manual de usuario

Nibe

Nibe F1145 series Guía del usuario

Nibe

Nibe F2120 Series Guía del usuario

Nibe

Nibe CLIMATEMASTER Tranquility TES Guía

Nibe

Nibe S1256 Guía del usuario

Nibe

Nibe F470 Manual de usuario

Nibe

Nibe FIGHTER 1120 Instrucciones de funcionamiento y mantenimiento

Manuales populares de Bomba de calor de otras marcas

MICROWELL

MICROWELL HP 1000 GREEN Manual de usuario

Sanyo

Sanyo SAP120FCH Manual de usuario

Daikin

Daikin EHYHBH05AA Manual de usuario

Panasonic

Panasonic WH-SDF03E3E5 Guía

Bryant

Bryant 544B Manual de usuario

Airxcel

Airxcel 45000 Series Manual

Mitsubishi Electric

Mitsubishi Electric PUZ-SWM60VAA Manual de usuario

Dimplex

Dimplex LI 16I-TUR Guía del usuario

Carrier

Carrier WSHP Open v3 Guía de configuración rápida

TGM

TGM CTV14CN018A Manual de usuario

Carrier

Carrier 38MGQ Series Manual de usuario

Kokido

Kokido K2O K880BX/EU Guía de solución de problemas

Viessmann

Viessmann VITOCAL 300-G PRO Type BW 2150 Guía rápida

Carrier

Carrier 48EZN Manual de usuario

Viessmann

Viessmann KWT Vitocal 350-G Pro Series Instrucciones de funcionamiento

Ariston

Ariston NIMBUS Manual de usuario

Weishaupt

Weishaupt WWP L 7 Guía del usuario

GE Zoneline AZ85H09EAC Manual de usuario