Nexa DORNIER DO-27 Manual de usuario
DORNIER
Radio control model
R/C Flugmodell
MONTAGEANLEITUNG
INSTRUCTION MANUAL
SPECIFICATIONS
Wingspan 63 in.
Length 47.6 in.
Electric Motor (See next page)
Glow Engine .46 2Stroke / .52 4-Stroke
Radio 6 Channel / 6-7 Servos
WARNING! This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and
cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.
Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.
ACHTUNG! Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt,
die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen Bei unsachgemäßer Verwendung kann
hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um
professionelle Unterstützung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist
durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.
TECHNISCHE DATEN
Spannweite 1620mm
Lange 1210mm
Elektroantrieb (siehe nächste Seite)
Verbrennerantrieb 7.5cc 2-T / 8.5cc 4-T
Fernsteuerung 6 Kanal / 6-7 Servos
DO-27
Designed for brushless electric motors (.46-.52 class glow conversion optional)
Entwickelt für Brushless Elektro Motoren (7,5 -8,5cc Glühzündermotor Einbau möglich)
Full the elevator out of the
horizontal stabilizer.
Cut away only
the film both side
1A
1B
When you are satisfied with the alignment,
use a pencil to trace around the top and
bottom of the stabilizer where it meets the
fuselage.
Cut away only
the covering
both side
BB’
B=B’
Aluminum wing joiner
Remove the horizontal stabilizer from the
fuselage. Using the sharp hobby knife,
carefully cut away the covering inside the
lines which were marked above.
* WARNING: When removing any covering
from the airframe, please ensure that you
secure the cut edge with CA or similar
cement. This will ensure the covering
remain tight.
Stabilizer
AA’
A=A’
Stabilizer
FUSELAGE
Again, Install the horizontal stabilizer into the
fuselage and adust the alignment as described
in steep 1C. Secure the horizontal stabilizer in
place using CA glue.
1C
1D
1E
DORNIER DO-27 1-Horizontal stabilizer
Note: The slots for the control horn
installation are pre- cut at factory.
Control horn
...........2
CA
CA
Thin CA glue
Thin CA glue
Push the elevator and its hinges into the hinge slots in the trailing edge of the
horizontal stabilizer.
There should be a minimal hinge gap.
When satisfied with the and alignment, hinge the elevator to the horizontal stabilizer using CA glue.
Hinge STABILIZER
CA
Apply thin CA to both
side of the hinge
Full the rudder out of the
vertical stabilizer.
2A
2B
2C
3A 3B
WARNING! Securely glue together.
If coming off during flights, you lose control
of your airplane which leads to accidents !
Vergewissern Sie sich, sauber geklebt zu haben.
Andernfalls konnen Probleme mit der Flugeigenschaft
auftreten!
CA
DORNIER DO-27 3-Vertical stabilizer
DORNIER DO-27 2-Horizontal stabilizer
When you are satisfied with the alignment,
use a pencil to trace around the right and
left of the stabilizer where it meets the
fuselage.
Cut away only
the covering
both side
Realign the vertical stabilizer, then glue
the vertical stabilizer into the fuselage,
using a generous amount of thin CA.
CA
CA
Thin CA glue
Thin CA glue
Hinge STABILIZER
CA
Apply thin CA to both
side of the hinge
Push the rudder and its hinges into the hinge slots in the trailing edge of the
horizontal stabilizer. There should be a minimal hinge gap.
When satisfied with the and alignment, hinge the elevator to the horizontal stabilizer using CA glue.
4A
4B 4C
4D
4E
WARNING! Securely glue together.
If coming off during flights, you lose control
of your airplane which leads to accidents !
Vergewissern Sie sich, sauber geklebt zu haben.
Andernfalls konnen Probleme mit der Flugeigenschaft
auftreten!
WARNING! Securely glue together.
If coming off during flights, you lose control
of your airplane which leads to accidents !
DORNIER DO-27 4-Vertical stabilizer
Note: The slots for the control horn
installation pre- cut at factory.
Control horn
...........2
3x12mm screw
.......................2
......................1
1.5mm
3x12mm screw
Collar
CA
DORNIER DO-27 5-Rudder control horn
WARNING! Securely glue together.
If coming off during flights, you lose control
of your airplane which leads to accidents !
DORNIER DO-27 6-Tail wheel
2mm
FUSELAGE
..................2
3x12mm bolt
...........2
7A
.........4
3X15mm hex bolt
Cut off the shadow area
......2
4X40mm screw
4mm nut
............................2
............................6
4mm washer
4mm nut
4x40mm screw
Aluminum landing gear
DORNIER DO-27 7- Main gear
7B
7C
Using a aluminum motor mounting plate as a template, mark
the plywood motor mounting plate where the four holes are
to be drilled (A).
Remove the aluminum motor mounting plate and drill a 3mm
hole through the plywood at each of the four marks marked (B).
Using a plywood motor mounting
plate as a template, mark the fire-
wall where the four holes are to
be drilled (C) .
Aluminum motor mounting plate
(included with electric motor set)
Push the four 5x35mm bolts through
the fire-wall as shown (E)
Reposition the plywood motor
mounting plate and secure
it in place with twelve 5xmm nuts and
washers (E).
Pull the magnetic battery hatch
out of the fuselage
8B
! Align the mark on plywood
motor mounting with the center
mark on the fire-wall
!
C
8C
Plywood motor
mounting
A
B
8A
Remove the plywood motor
mounting plate and drill a 5mm
hole through the fire-wall at
each of the four marks marked
above (D).
5mm
8D
5mm
8E
DORNIER DO-27 8- Electric motor
F
Firewall
113mm
B’
B
B=B’
A
A=A’
A’ ! Engine thrust on balk head
is already adjust at factory
Attach the aluminum motor mounting
plate on to the motor and secure it in
place with four screws ( included with
motor set) (F).
TOP-VIEW / Draufsicht
SIDE-VIEW / Seitenansicht
Sturz und Zug beachten!
Sperrholztrager Platten zusammenkleben, wie gezeigt ausrichten
und Locher bohren.
Motor nach untenstehendem Schema einbauen.
Fur optimale Leistung empfehlen wir folgende Komponenten:
-Brushless-Motor PICHLER BOOST 60
-Brushless Regler PICHLER XQ-70
-LiPO Akku LEMONRC 3700-5S
-Luftschraube 12*6 - 13*8
For maximum performance, we recommended
the following:
-Brushless-Motor PICHLER BOOST 60
-Brushless Regler PICHLER XQ-70
-LiPO Battery LEMONRC 3700-5S
-Propeller 12*6 - 13*8
Throttle pushrod
FRONT
Elevator pushrod
Elevator servo
Rudder servo
(mini servo)
Throttle servo
BOARD - TOP VIEW
FUSELAGE - BOTTOM VIEW
FUSELAGE - BOTTOM VIEW
The holes for the rudder servo
are Pre-cut at factory (left and
right side of the fuselage).
Cut away only the covering
Akku Kiettband
aus dem PICHLER
Sortiment
Best.Nr. C4739
Battery seat bell
X
Tipp
10A
10B 10C
DORNIER DO-27 9- Electric motor continued
DORNIER DO-27 10- Servo & linkage
1.5mm
1/16
2mm
L/R
X
X
BOTTOM - VIEW / Unteransicht
Cut here for standard servo
Aileron & flap
extension cord
Trial fit the control horn into
the slot.
If the parts will join, but with
a gaps, sand or trim the parts
a little at a time until the parts
meet exactly with no gaps.
CA
Plastic control horn
Linkage Stopper set
.....................4
.................4
1.2mm O Alenk-Gestange
Aileron & flap pushrod
CA
CA
Do the same way with other wing half
Metal hook (x2)
Spring (x1)
L/R
Do the same way with other wing half
CA
DORNIER DO-27 11- Cowling
2.5x10mm screw
..........4
DORNIER DO-27 12- Wing
DORNIER DO-27 13- Joining the wing
IMPORTANT: Please do not clean your model with pure alcohol, only use liquid soap with water or use glass cleaner
to clean on surface of your model to keep the colour not fade.
Note: Cut out the stickers and apply them in the
proper area. Do not peel the backing paper off all
at once.
Peel off one corner of the backing and cut off with
scissors.
Arrange sticker on model and when satisfied adhere
the corner without backing.
Carefully peel back the rest of the backing while at
the same time adhering the rest of the sticker.
Try not to make air bubbles, if there are some,
carefully puncture sticker (center of bubble) but not
model surface with the tip
of the knife or sharp pin and squeeze out the air.
At curves stretch sticker and apply a little heat so
that no ceases occur.
Cut off the excess that is produced.
DORNIER DO-27 14- Joining the wing
DORNIER DO-27 15- Decor
Tabla de contenidos
Otros manuales de Juguete de Nexa
Nexa
Nexa Pilatus Porter PC-6 Manual de instrucciones
Nexa
Nexa U.S NAVY DIVE BOMBER SBD-5 DAUNTLESS Manual de usuario
Nexa
Nexa NE-1 NAVY CUB Manual de usuario
Nexa
Nexa MESSERSCHMITT Me-109 Manual de usuario
Nexa
Nexa Dago red Unlimited Air Racer 4 Manual de usuario
Nexa
Nexa Pilatus Porter PC-6 Manual de usuario
Nexa
Nexa BEECHCRAFT T-34C TURBO MENTOR MILITARY... Manual de usuario
Nexa
Nexa AGWAGON C188 Manual de usuario
Nexa
Nexa P-39 Q/N AIRACOBRA Manual de instrucciones
Nexa
Nexa Royal Air Force Supermarine Spitfire Manual de usuario
Nexa
Nexa CURTISS P-40 Manual de usuario
Nexa
Nexa MITSUBISHI A6M5 ZERO Manual de instrucciones
Nexa
Nexa YAK-9 Manual de usuario
Nexa
Nexa CE-208 Manual de usuario
Nexa
Nexa Tri-Pacer Piper PA-22 Manual de usuario
Nexa
Nexa MACCHI MC 205 Manual de usuario
Nexa
Nexa Focke Wulf FW-190A Manual de usuario
Nexa
Nexa P-38 Lightning Manual de usuario
