Newport INF-B Manual de usuario

INF-B

Embedded Ethernet Server

Operator’s Manual

http://www.newportUS. om/manuals

NEWPORT

Electronics,Inc.

THE NEW STANDARD FOR QUALITY

Counters

Frequency Meters

PID Controllers

Cloc /Timers

Printers

Process Meters

On/Off

Controllers

Recorders

Relative

Humidity

Transmitters

Thermocouples

Thermistors

Wire

Rate Meters

Timers

Totalizers

Strain Gauge

Meters

Voltmeters

Multimeters

Soldering Iron

Testers

pH pens

pH Controllers

pH Electrodes

RTDs

Thermowells

Flow Sensors

For Immediate Assistance

In the U.S.A. and Canada: 1-800-NEWPORT

In Mexico: (95) 800-NEWPORT

Or call your local NEWPORT Office.

Internet e-mail

[email protected]

Additional products from

NEWPORTnetSM On-Line Servi e

www.newportUS.com

NEWPORT

Electronics,Inc.

It is the policy of NEWPORT to comply with all worldwide safety and EMC/EMI regulations that apply. NEWPORT is constantly

pursuing certification of its products to the European New Approach Directives. NEWPORT will add the CE mar to every

appropriate device upon certification.

The information contained in this document is believed to be correct but NEWPORT Electronics, Inc. accepts no liability for any

errors it contains, and reserves the right to alter specifications without notice.

WARNING: These products are not designed for use in, and should not be used for, patient connected applications.

TRADEMARK NOTICE:

, NEWPORT, NEWPORT

and newportUS. om are trademar s of NEWPORT

Electronics, Inc.

PATENT NOTICE: This product is covered by one or more of the following patents: U.S. Pat. No. Des. 336,895; 5,274,577/

CANADA 2052599; 2052600/ ITALY 1249456; 1250938 / FRANCE BREVET No. 91 12756 / SPAIN 2039150; 2048066 / UK

PATENT No. GB2 249 837; GB2 248 954 / GERMANY DE 41 34398 C2. The ™is a Trademar of OMEGA Engineering, Inc.

Used Under License. Other US and International Patents pending or applied for.

This device is mar ed with the international caution symbol. It is important to read the Setup Guide before installing or

commissioning this device as it contains important information relating to safety and EMC.

TABLE OF CONTENTS

Part 1: Introdu tion

1.1 Safety and EMC Considerations........................................................................2

1.2 Des ription ..........................................................................................................3

Part 2: Hardware

2.1 Physi al Chara teristi s and Mounting ...........................................................4

2.2 Rear Panel of Meter with Embedded Ethernet Server .....................................4

2.3 DIP Swit hes on the iServer...............................................................................5

2.4 Network Communi ation Interfa es .................................................................6

2.4.1 10Base-T RJ-45 Pinout.........................................................................6

2.4.2 10Base-T Crossover Wiring.................................................................6

Part 3: Network Configuration

3.1 Network Proto ols .............................................................................................7

3.2 Ethernet (MAC) Address ....................................................................................7

3.3 DHCP ...............................................................................................................8

3.4 DNS ...............................................................................................................8

3.5 IP Address ...........................................................................................................9

3.5.1 Default IP Address ................................................................................9

3.6 Port Number ........................................................................................................9

Part 4: Operations

4.1 Serial Interfa e Configuration-Communi ation Proto ol..............................10

4.2 Command Stru ture..........................................................................................10

4.3 Command Formats ...........................................................................................10

4.4 Operations .........................................................................................................12

4.5 Setup and Operation using a Web Browser ..................................................12

4.5.1 Read Devi es .....................................................................................14

4.5.1.1 Devi e Setpoints ................................................................................14

4.5.2 Send Raw Command ..........................................................................14

4.5.3 Devi e Setup .......................................................................................15

4.5.3.1 Modify Devi e Parameters (or Devi e List Entry)............................15

4.5.4 Configuration ......................................................................................16

4.5.5 A ess Control ..................................................................................19

4.6 Setting a New IP Address over the Network ..................................................21

4.7 Terminal Server Fun tion ................................................................................22

4.8 Terminal Emulation ...........................................................................................23

4.9 Telnet Setup ......................................................................................................24

4.10 HTTPGET Program............................................................................................26

4.11 ARP Proto ol .....................................................................................................27

4.12 Remote A ess (Tunneling) .............................................................................28

4.12.1 Remote iServer ..................................................................................29

4.12.2 Lo al iServer ......................................................................................30

4.13 Mail Notifier Software .......................................................................................31

4.13.1 Installation...........................................................................................31

4.13.2 Program Options Setup and Configuration ....................................32

4.13.3 Devi e Setting Setup and Configuration ..........................................33

Part 5: Spe ifi ations .................................................................................................................. 34

Part 6: Fa tory Preset Values ......................................................................................................35

Appendix A Glossary.............................................................................................................36

Appendix B IP Address ........................................................................................................37

Appendix C IP Netmask.........................................................................................................38

Appendix D ASCII Chart .......................................................................................................39

ASCII Chart Control Codes .............................................................................40

Part 7: Approvals Information

7.1 Ele tromagneti Compatibility (EMC) ............................................................41

7.2 FCC ..............................................................................................................41

LIST OF FIGURES:

Figure 1.1 iServer on the Ethernet Network.................................................................3

Figure 2.1 Rear Panel View of Meter with Embedded Ethernet Server .....................4

Figure 2.2 DIP Swit hes on the iServer ........................................................................5

Figure 2.3 Option Card Installation...............................................................................5

Figure 2.4 RJ45 Pinout ..................................................................................................6

Figure 2.5 10Base-T Crossover Cable Wiring .............................................................6

Figure 3.1 Labeling ........................................................................................................7

Figure 3.2 DIP Swit h on the iServer ...........................................................................8

Figure 4.1 Pinging eis03e MS-DOS Prompt ............................................................12

Figure 4.2 Devi e Type ............................................................................................... 13

Figure 4.3 iServer Home Page Menu .........................................................................13

Figure 4.4 Login and Administrator Password .........................................................13

Figure 4.5 Read Devi es ............................................................................................ 14

Figure 4.6 Devi e Setpoints ...................................................................................... 14

FIgure 4.7 Serial Devi e Query .................................................................................. 14

Figure 4.8 Devi e Setup ............................................................................................. 15

Figure 4.9 Modify Devi e Parameters ....................................................................... 15

Figure 4.10 Configuration ............................................................................................ 16

Figure 4.11 A ess Control ......................................................................................... 19

Figure 4.12 A ess Control .........................................................................................21

Figure 4.13 Terminal Server Configuration .................................................................22

Figure 4.14 Terminal Emulation ....................................................................................23

Figure 4.15 Tera Term Telnet Conne tion S reen ......................................................24

Figure 4.16 Telnet Setup Menu - iServer Configuration Page ...................................24

Figure 4.17 Telnet Setup Menu - iServer Help Page ...................................................25

Figure 4.18 ARP Commands and Responses .............................................................27

Figure 4.19 PC-to-Devi e Communi ation...................................................................28

Figure 4.20 Devi e-to-Devi e Communi ation ............................................................28

Figure 4.21 Configuration Menu - Remote iServer......................................................29

Figure 4.22 Configuration Menu - Lo al iServer..........................................................30

Figure 4.23 iServer Mail Notifier Main Window............................................................31

Figure 4.24 iServer Mail Notifier Profile Setup ............................................................32

Figure 4.25 iServer Mail Notifier Devi e Setting .........................................................33

LIST OF TABLES:

Table 2.1 Rear Panel Annun iators ............................................................................5

Table 4.1 Command Prefix Letters ...........................................................................10

Table 4.2 Command Formats ....................................................................................10

NOTES, WARNINGS and CAUTIONS

Information that is especially important to note is identified by following labels:

• NOTE

• WARNING or CAUTION

• IMPORTANT

• TIP

NOTE: Provides you with information that is important to successfully

setup and use the iServer.

CAUTION or WARNING: Tells you about the ris of electrical shoc .

CAUTION, WARNING or IMPORTANT: Tells you of circumstances or

practices that can effect the instrument’s functionality and must refer

to accompanying documents.

TIP: Provides you helpful hints.

Before You Begin

Inspe ting Your Shipment:

Remove the pac ing slip and verify that you have received everything listed. Inspect the

container and equipment for signs of damage as soon as you receive the shipment. Note

any evidence of rough handling in transit. Immediately report any damage to the shipping

agent. The carrier will not honor damage claims unless all shipping material is saved for

inspection. After examining and removing the contents, save the pac ing material and

carton in the event reshipment is necessary.

Customer Servi e:

If you need assistance, please contact the Customer Service Department nearest you.

Manuals, Software:

The latest Operation Manual as well as free configuration software and iServer Mail

Notifier are available at the website listed on the over page of this manual or on the

CD-ROM en losed with your shipment.

PART 1

INTRODUCTION

1.1 Safety and EMC Considerations

This device is mar ed with the international caution symbol. It is important to

read this manual before installing or commissioning this device as it contains

important information relating to Safety and EMC (Electromagnetic

Compatibility).

This instrument is a panel mount device protected in accordance with EN 61010-

1:2001, electrical safety requirements for electrical equipment for measurement,

control and laboratory. Installation of this instrument should be done by qualified

personnel. In order to ensure safe operation, the following instructions should be

followed.

This instrument has no power-on switch. An external switch or circuit-brea er

shall be included in the building installation as a disconnecting device. It shall be

mar ed to indicate this function, and it shall be in close proximity to the

equipment within easy reach of the operator. The switch or circuit-brea er shall

meet the relevant requirements of IEC 947–1 and IEC 947-3 (International

Electrotechnical Commission). The switch shall not be incorporated in the main

supply cord.

Furthermore, to provide protection against ex essive energy being drawn from

the main supply in case of a fault in the equipment, an over urrent protection

device shall be installed.

• Do not exceed voltage rating on the label located on the top of the

instrument housing.

• Always disconnect power before changing signal and power connections.

• Do not use this instrument on a wor bench without its case for safety

reasons.

• Do not operate this instrument in flammable or explosive atmospheres.

• Do not expose this instrument to rain or moisture.

• Unit mounting should allow for adequate ventilation to ensure instrument

does not exceed operating temperature rating.

• Use electrical wires with adequate size to handle mechanical strain and

power requirements. Install without exposing bare wire outside the connector

to minimize electrical shoc hazards.

EMC Considerations

• Whenever EMC is an issue, always use shielded cables.

• Never run signal and power wires in the same conduit.

• Use signal wire connections with twisted-pair cables.

• Install Ferrite Bead(s) on signal wires close to the instrument if EMC

problems persist.

Failure to follow all instru tions and warnings may result in injury!

1.2 Des ription

This iServer is designed to connect industrial devices with serial interfaces to the

Ethernet networ using the TCP/IP protocol. It contains an Ethernet Server interface.

The standard features include:

• Use standard Web Browser (TCP/IP protocol), HTTPGET DOS program or Telnet

Simulation, for networ connectivity.

• Use a standard home page or customize web page for OEM applications.

For this Ethernet Option, the Communication Menu is only used for internal

interface with the Ethernet Option. There is no RS-232 or RS-485 for the user

to access. The setting in the Communication Menu should be: 9600 baud rate,

1 stop bit, odd parity and RS-232. For the server side, the settings would be

the same.

The following example illustrates how you can hoo up the devices with serial interface

on the net using the iServer:

Figure 1.1 iServer on the Ethernet Network

TX RX RTN

COMMUNICATIONS

ETHERNET

DC POWER IN

RX TX ON COL

RESET

+ - N/C

Meters and

PART 2

HARDWARE

2.1 Physi al Chara teristi s and Mounting

For physical dimensions and installation instructions reference the Quic start and

Operator’s Manual .

2.2 Rear Panel of Meter with Embedded Ethernet Server

Figure 2.1 Rear Panel View of Meter

with Embedded Ethernet Server

Table 2.1 Rear Panel Annun iators

Network Communi ation Interfa e Se tion:

ETHERNET RJ45 interface for 10BASE-T connection.

RESET Button: Used for power reseting the iServer.

COL LED (Red) Blin ing: Indicates networ activities (receiving or sending pac ets).

ON LED (Green) Solid: Indicates good networ lin .

1111

119

P6 P7 P18A P18B

ETHERNET

RESET

COL

2.3 DIP Swit hes on the iServer

For Dipswitch access you must remove the main board from the case. Refer to the

Disassembly Instructions in your Quic start or Operator’s Manual.

Figure 2.2 DIP Swit hes on the iServer

Figure 2.3 Option Card Installation

SIGNAL INPUT BD

AC POWER BD

ETHERNET BD

J10

J11

J12

P11

SW2

1OFF

P11

The iServer is shipped with all

DIP switches in "OFF" position

1 To change the IP address

from the serial port

2 To change to default factory

settings

3 To enable/disable DHCP

4 To enable/disable Terminal

Server function

2.4 Network Communi ation Interfa es

2.4.1 10Base-T RJ-45 Pinout

The 10BASE-T Ethernet networ (RJ-45) system is used in the iServer for networ

connectivity. The 10 Mbps twisted-pair Ethernet system operates over two pairs of

wires. One pair is used for receiving data signals and the other pair is used for

transmitting data signals. This means that four pins of the eight-pin connector are used.

Figure 2.4 RJ45 Pinout

2.4.2 10Base-T Crossover Wiring

When connecting the iServer directly to the computer, the transmit data pins of the

computer should be wired to the receive data pins of the iServer, and vice versa. The

10Base-T crossover cable with pin connection assignments are shown on Figure 2.5.

Figure 2.5 10Base-T Crossover Cable Wiring

Use straight through cable for connecting the iServer to an Ethernet hub.

The ports on the hub are already crossed.

COL

Pin Name Des ription

1 +Tx + Transmit Data

2 -Tx - Transmit Data

3 +RX + Receive Data

4 N/C Not Connected

5 N/C Not Connected

6 -Rx - Receive Data

7 N/C Not Connected

8 N/C Not Connected

Otros manuales para INF-B

Tabla de contenidos

Otros manuales de Servidor de Newport

Newport

Newport iServer MicroServer EIS-PCB Manual de usuario

Newport

Newport iServer Series Manual de usuario

Manuales populares de Servidor de otras marcas

HP AlphaServer ES47 Manual de usuario

Dell

Dell PowerEdge R410 Manual de usuario

PowerNAS

PowerNAS CMA Manual de usuario

Supero

Supero FatTwin F617R3-FT Manual de usuario

MSI

MSI P1-109N-L70 Manual de usuario

Dell

Dell PowerEdge XE9640 Manual

Dell

Dell PS4100 Instrucciones de montaje

EtroVISION

EtroVISION EV3151 Manual de usuario

NEC

NEC Express5800/T110j Manual de usuario

HP ProLiant Gen9 Manual de usuario

Compaq

Compaq ProLiant 3000 Manual

Dell

Dell PowerEdge 3YPMN Manual de usuario

iRobo

iRobo IPC2U Manual de usuario

Nortel

Nortel 1000 Con?guration guide Manual de usuario

Asus

Asus AP7500 Manual de operación y mantenimiento

Avid Technology

Avid Technology AirSpeed 5000 Manual de usuario

HP Integrity rx2600 Guía de instalación

Milestone

Milestone Husky IVO 350T Manual de usuario