NewLine TradePro Curved Manual de usuario
TradePro Curved
INSTRUCTION MANUAL
1. When you receive your Newline shower check contents for any freight damage.
2. Advise Newline on 0508 639 5463 if any damage has occurred or a defect
LGHQWLзHGZLWKLQKRXUVRIUHFHLYLQJWKHJRRGVVRWKLVFDQEHUHFWLзHG
3. Do not install any faulty product as this will invalidate later claims.
Important!
April 2020
WARRANTY
Faulty goods are covered under warranty. Visit www.newline.co.nz for warranty information.
Breakages incurred during construction are not covered under warranty.
Installations must conform to the instructions to be covered by the warranty.
HEALTH AND SAFETY
Toughened Glass:
• Do not rework precut glass panels. Cutting or altering a glass panel will cause it to explode without warning.
• 7PRCEMCNNINCUUCUUGODNKGU5VCPFINCUUQPUQHVRCEMCIKPIQPVJGƀQQTCPFCICKPUVCYCNN%CTGOWUVDGVCMGP
not to strike any edge or corner against a hard surface as this will chip and destroy the glass panel.
Installation:
• Glass panels and assemblies are heavy. Two man lifting is recommended for handling and installation.
• Determine positioning of wiring and piping within wall cavities before shower installation. Mark their positions to
ensure electrical and piping areas are avoided.
• Wear appropriate protective clothing and eye protection during installation.
MATERIALS REQUIRED
5KMC5KNCƀGZ0)6TCPUNWEGPV5KNKEQPG
TOOLS REQUIRED
AFTERCARE
0GYNKPGTGEQOOGPFUSWGGIGGKPIFQYPVJGINCUUCHVGTGXGT[UJQYGTCPFENGCPGFYGGMN[YKVJCOKETQſDGTENQVJ
OKNFFGVGTIGPVCPFYCVGT4KPUGYKVJENGCPYCVGTCPFUSWGGIGGCPFYKRGFT[
NEWLINE RECOMMENDS A SKILLED TRADESMAN ACQUAINTED WITH
SHOWER INSTALLATIONS TO ENSURE THE VERY BEST OUTCOME.
DOOR SET / IMPORTANT INFORMATION
ENSURE YOU TICK THE SPECIFIC BOXES THAT APPLY AS YOU PROGRESS
Curved SJQYGT'PUWTGVJGƀQQTKUNGXGNCPFVJGYCNNUCTGRNWODCPFƀCV
2QUKVKQPCNNHTCOKPIHQTUQNKFſZKPIHQTVJGUJQYGTVTC[UJQYGTCPFRNWODKPIſVVKPIU
YCNNRTQſNGUTGSWKTGCUVWFEGPVTGFOODCEMHTQOVTC[QWVUKFGGFIG.
Ensure all plumbing items have been installed prior to the lining being attached.
ACRYLIC TRAY AND LINER
• Detailed installation instructions are packed with the shower tray for tray and lining installation.
2
3
[1]
[14]
Before commencing installation, please ensure you have the following components in your package to
complete installation.
ASSEMBLY DIAGRAM
REF DESCRIPTION PART NO. QTY REF DESCRIPTION PART NO. QTY
1 Screws M3.5x35
SCREW PACK
PAR7296
14 9 Bump stop caps PAR6848 8
2 Wall plug (concrete) 6 10 Door panels 2
3 Screw cap covers 6 11 Top rollers PAR5124 4
4 Screws M4x10 6 12 Handle sets K9751 2
5 Wall channels PAR5094 2 13 Magnetic seals STE2878 2
6 Top and bottom
horizontal rails (curved)
900 PAR4592 2 14 Spacer blocks 4
1000 PAR4608
7:DWHUGHHFWRUV STE2922 4 15 Bottom rollers PAR5131 4
8 Fixed panels 2
4
LAYOUT PLAN
A
BB
13mm
A
SHOWER TYPE WALL CHANNEL POSITION (B)
900mm x 900mm 870mm (Minimum) to 890mm (Maximum)
1000mm x 1000mm 970mm (Minimum) to 990mm (Maximum)
IMPORTANT:
Position the wall channels at 13mm off the Acrylic tray edge (Diagram A). This will allow for
walls out of plumb protruding or curving inwards up to 4mm. Greater variations to plumb
will require recalculated reduction of Diagram A.
MINIMUM AND MAXIMUM TABLE
The Minimum and Maximum table is intended for shower installations outside of the package
installation being outlined. Walls out of plumb will not allow the full minimum/maximum range.
INSTALLATION STEPS PAGE 5 TO 8
5
A A
B1
SCREW M3.5 X 35
11
3
3
2
2
44
B
B
B
B
B1
A1
A A
SCREW M3.5 X 35
Note: Use lubricant on screws that
fasten into top & bottom rails.
Note: Apply a small bead of
silicone at joint as indicated prior
to fully fastening up. Clean off
excess.
1
2
3
4HYRV\[[OLWVZP[PVUPUNVM[OL^HSSWYVÄSLZYLMLY[V[OL3H`V\[7SHUVUWHNLMVYTLHZ\YLTLU[Z
Using a soft pencil or masking tape mark out the outside boundary line on the base and up the walls
with a spirit level. Use the wall channel holes to pre-drill a 2mm lead hole in the lining.
( ,UZ\YL[OLZWHJLYISVJRZHYLPUWVZP[PVUYLMLY[VHZZLTIS`KPHNYHTVUWHNLP[LT
) ;HRL[OLIV[[VTJ\Y]LKOVYPaVU[HSYHPSHUKPUZ[HSS[OL[^VÄ_LKWHULSZ56;,!;OLZJYL^OVSLZ
PU[OLÄ_LKWHULSWYVÄSLZHYLVMMZL[*OLJR[OH[[OLZLHSPNU^P[O[OLZJYL^SVJH[PVUZPU[OLJ\Y]LK
OVYPaVU[HSYHPSZ0M[OL`KVUV[SPUL\WJOHUNLV]LY[OLÄ_LKWHULSZ<ZL_MYHTLZJYL^Z
Add the top horizontal rail using the M3.5 x 35 screws fasten this frame together.
INSTALLATION
7YPVY[V^HSSJOHUULSÄ_PUN
Apply a continuous 7mm bead
of silicone on back of channel
plus short bead across tray to
liner join at base of channel. A
B
B
C
C
DD
AA
IMPORTANT: Complete all items in 2
& 3 before intalling to wall channels
INSTALLATION
4
5
6
2
1 1
1
1
1b
1a
VIEW FROM INSIDE
A
A1
B1 B2 C1 C2
A2
C
B B
A
A
AA1
A2
A
B
Fit the frame into the wall channels.
Fit the door assemblies as illustrated.
Detailing of shower assembly:
• A1 and A2: Fit the Door handles
• %DQG%)LWZDWHUGHHFWRUVWRGRRUHGJHVDQGOHDGLQJHGJHRI[HGIURQWSDQHOV
• C1 and C2: Fit magnetic seals to each door edge.
• Align shower frame evenly to wall channels, tray edge and plumb up frame.
1
2
A
B
56;,!<ZLI\[[VU
(YYV^[VKLWYLZZ
the bottom roller
to enter or remove
from bottom rail.
Adjustment
7
INSTALLATION
7
8
A
A1
A2
ADJUST THE SLIDING DOORS USING
THE SCREWS LOCATED ON THE
BOTTOM OF TOP ROLLER ASSEMBLIES.
ADJUST ROLLERS SO THAT THE
SLIDING DOORS ARE PARALLEL TO
EACH OTHER.
NOTE: DO NOT OVER TIGHTEN TOP
ROLLERS AS THIS WILL CAUSE THE
BOTTOM ROLLERS TO JAM AND BREAK
!
A2 A3A1
ENSURE THAT THE CHOSEN POSITION IN 1A
AVOIDS DRILLING THROUGH THE GLASS.
!
O 0.32
SCREW M4x10
CHECK FOR LEVEL
VIEW FROM INSIDE
Adjust the sliding doors as shown in the illustration below.
A. Double check the frame alignment including levelling the top horizontal Rail to ensure that
the whole frame sits square on the shower.
% )URPWKHLQVLGHDWWDFKWKHZDOOFKDQQHOVZLWK0[VFUHZVWRWKH[HGJODVVH[WUXVLRQ
C. Put bump stop covers on.
IMPORTANT NOTE: Check detail (A1) for screw position so the glass is not touched.
CONTACT
Freephone: 0508 639 5463 Phone: 09 444 2053 Fax: 09 443 0044
9
ALLOW 24 HOURS FOR SILICONE TO FULLY DRY
BEFORE USE.
!
Silicone is not used on the inside of the
shower screen because water can build
up over time within the wall channel and
leak out of the shower area. The screen
is designed to allow the water to return
into the shower area, if any is present.
SCREENS THAT ARE SEALED ON THE
INSIDE WILL VOID WARRANTY.
!
Apply silicone sealer around the outside join only as diagram.
Tabla de contenidos
Otros manuales de Cabina de ducha de NewLine
