NeuroDigital Avatar VR Manual de usuario
AVATAR VR - QUICK START GUIDE 1
Quick Start Guide
BY NEURODIGITAL TECHNOLOGIES S.L.
DEVELOPMENT KIT - VERSION 2.0 - JUNE 2019
AVATAR VR - QUICK START GUIDE
2
Minimum System Specs
Operating System Windows 8.1 or newer
Processor AMD Phenom™ II or Intel® Core™ i3 processor or greater
Memory 2GB + RAM
Input 1x USB 2.0 port for wired operation
Bluetooth 4.0 Dual Mode for wireless operation
Requires internet connection
Devices with a VR HMD requires a “VR Ready” system
Operating System Windows 8.1 or newer
Graphics Card NVIDIA GTX 970 / AMD R9 290 equivalent or greater
Processor Intel i5-4590 equivalent or greater
Memory 8GB + RAM
Input 3x USB 3.0 ports
Output Compatible HDMI 1.3 video output
Bluetooth 4.0 Dual Mode for wireless operation
AVATAR VR - QUICK START GUIDE 3
Content
01 Package contents
02 Avatar VR parts
03 Connecting the TrackBand
04 Using Avatar VR by Bluetooth
05 Using Avatar VR by USB
06 Initialization
07 Color code
08 Put the glove on
09 Avatar VR Collocation
10 Calibrating the Thumb
11 Calibrating in demo
12 Removing the glove
AVATAR VR - QUICK START GUIDE
4
01 PACKAGE CONTENTS
Remove the contents from the box carefully. If any part is missing or
The kit contains the following:
Avatar VR (Le, right or both
depending on your order)
TrackBand
2 USB-C Cable for TrackBand Right
2 USB-C Cable for TrackBand Le
IMPORTANT: For battery calibration,
before using the device, you must perform
a rst full charge with a less than 500mA
charger or, failing that, via USB cable
connected to your computer. This process
can last, at least, 2:30 hours.
Depending on your order
1
2
0
1
4
5
0
4
AVATAR VR - QUICK START GUIDE 5
02 AVATAR VR PARTS
The fabric composion is 80%
polyamide with 20% elastomer.
1
2
3
4
5
6
IMU Sensors
Actuators
Power Button
USB Port
Li-Po Battery
Breathable areas
Conductive zones
Flex Sensor
TrackBand
1
2
3
4
5
5
5
5
6
7
7
AVATAR VR - QUICK START GUIDE
6
03 CONNECTING THE TRACKBAND
1
2
4L
5L
0
4
4
5
0
4
4
5
4L
4L
1R
2R
0
1
1
2
0
1
1R
2R
Connect the cables considering their numbering.
IMPORTANT: Changing the device’s numbers posion can cause errors.
AVATAR VR - QUICK START GUIDE 7
Connect the wrist connector of the TrackBand marked with a
number 0 to the glove.
Wrist Link
AVATAR VR - QUICK START GUIDE
8
Do not connect any micro-usb cable from Avatar VR to your
computer.
04 USING AVATAR VR BY BLUETOOTH
11
NO YES
Enable Bluetooth visibility: Do the “pinch” gesture for a second
while you see a cyan light icking and feel a short vibraon. A
permanent cyan light will conrm the Bluetooth mode is visible
and ready to be paired within 2 minutes.
2
AVATAR VR - QUICK START GUIDE 9
3Pair the device with your PC: Open the Bluetooth sengs tab in
your PC. Avatar VR should now appear as an accessible device.
Pair with the device and wait unl the pairing process nishes. It is
important to close this sengs tab once it is paired.
IMPORTANT: Close the Bluetooth sengs in order to make it
work properly.
AVATAR VR - QUICK START GUIDE
10
Connect the device with ND Suite via Bluetooth: Open the ND
Suite soware and click on the “Bluetooth” buon, then select the
device you just paired. In a few seconds, it will be connected.
(The ND Suite is required for Avatar VR to communicate with your
PC. To download the lastest version of the installer, go to hps://
avatarvr.es/developer/)
4
NDSuite
Click on the
“Bluetooth” button
NOTE: Next me you want to connect the device to your PC via
Bluetooth, you only have to perform Step 4.
Otros manuales para Avatar VR
1
Tabla de contenidos
