NetworX Architech Guía

ArchiTech Cylindrical Lock & Surface-Mounted Networx Control Unit Mounting and Installation Instructions

ArchiTech™by Networx™

FOR CYLINDRICAL LOCKS USING SURFACE-MOUNTED NETWORX CONTROL UNITS

MOUNTING AND INSTALLATION INSTRUCTIONS

DESCRIPTION

These instructions detail the hardware installation procedure for the ArchiTech cylindrical door locks using the Surface

-Mounted Networx Control Units for hollow metal and solid wood doors.

Installation instructions for the Door Contact Sensor, Door Contact Magnet (installed in the door jamb) and the

Oval and Rectangular Proximity Readers are also included.

PARTS OVERVIEW

For reference, the images in Fig. A display each component (not to scale). In addition to the various screws and tem-

plates included with your lock, please note that one of two types of Proximity Readers are included, either Oval or

Rectangular. In addition, one of two types of Door Contact Magnets (installed in door jamb) are included, ei-

ther 3/8" or 3/4" diameter.

Wires for the Door Contact Sensor, Proximity Reader and Cylindrical Lock motor are routed through the door

and are plugged into the rear of the Surface-Mounted Networx Control Unit, mounted on the inside ("protected")

door surface.

The Cylindrical Lock Motor Wire can be routed within hollow metal doors; with solid wood doors, this Cylindrical Lock

Motor Wire can be routed on the door surface but behind a Wiring Plate (HW1945), or an optional Cylindrical

Drill Jig (part #N90S1DJ) is available to allow a hole to be drilled allowing this wire to be routed through the

solid wood door.

REQUIRED TOOLS 

In addition to the standard door prep kit tools used to install a cylindrical lock into a metal or wood door (standard ASA

161 door prep cross-bore hole saws, Phillips and flat head screwdrivers, etc.), you will need: A small level, and the

following drill bit sizes: 5/8", 3/8", 3/4" and 7/64". If the Cylindrical Drill Jig (part #N90S1DJ) is used, a round or cir-

cular file is needed to remove burrs in holes and to file a pathway groove in wooden doors for the Cylindrical

Lock Motor Wire.

IMPORTANT: For installation on UL Listed Wood Fire Doors, fill the through hole wire passage with UL Clas-

sified Fire Stop Sealant after connecting all wiring and testing the Lock.

FIG. A: OVERVIEW OF BASIC PARTS (NOT TO SCALE)

"SURFACE-MOUNTED" NETWORX

CONTROL UNIT

AND ITS MOUNTING PLATE

OVAL AND RECTANGULAR

PROXIMITY READER COVERS AND

MOUNTING COMPONENTS

USE WIRING PLATE (LEFT)

OR OPTIONAL CYLINDRICAL

DRILL JIG (RIGHT)

DOOR CONTACT

MAGNET

(TWO TYPES)

DOOR

CONTACT

SENSOR

ArchiTech Cylindrical Lock & Surface-Mounted Networx Control Unit Mounting and Installation Instructions

DOOR PREP: INITIAL STEPS

1. INSPECT THE DOOR BEVEL

Inspect the door for a bevel and, if beveled, determine which side is "longer" in width and which side is "shorter" in

width (see "top view" example in Fig. 1). For beveled doors, be sure to use the correct marks printed on the template

for the correct length of the outside door surface (either the "long" or "short" side of the door).

2. PREP DOOR FOR CYLINDRICAL LOCK

If not done already, use standard door prep kit tools and the instructions included with the cylindrical lock to prep the

door and door jamb as required (standard ASA 161 door prep). These include the 5/16" and 2-1/8" thru-holes, the 1"

latch hole and mortising the door edge for the latch plate and mortising the door jamb for the strike plate.

Do not install the lock hardware yet.

DOOR 3½° bevel

Door Stop

Arc of door swing

Jamb

"Shorter side of

door"

"Longer side of

door"

FIG. 1: EXAMPLE OF BEVELED DOOR (TOP VIEW)

FIG. 2: USE TEMPLATE PROVIDED

ArchiTech Cylindrical Lock & Surface-Mounted Networx Control Unit Mounting and Installation Instructions

3. TAPE ON DOOR: "PROXIMITY READER" TEMPLATE (WI2098)

Remember, the Proximity Reader is always located on the outside

("unprotected" side) door surface.

Fold and place the template (WI2098) on the outside door edge (see arrow

in Fig. 3 for an example). Align the template with the "HORIZONTAL CEN-

TER LINE OF LEVER" as shown on the template. Tape the template in

place.

4. MARK TEMPLATE "PROXIMITY READER" HOLES

On the outside door surface, mark the two holes for the Proximity Reader mounting screws.

Mark the center of the 5/8" diameter thru-hole (used for the Cylindrical Lock Motor Wire, Proximity Reader and Door

Contact Sensor wires).

TIP: Take special notice of this 5/8" diameter thru-hole, as it is an essential hole for this installation and is refer-

enced several times throughout these instructions.

FIG. 3: EXAMPLE OF OUTSIDE DOOR

EDGE (ARROW)

FIG. 4. CLOSE UP OF WI2098 TEMPLATE FOR THE "PROXIMITY READER"

ArchiTech Cylindrical Lock & Surface-Mounted Networx Control Unit Mounting and Installation Instructions

5. MARK TEMPLATE "DOOR CONTACT SENSOR" HOLE

Mark the 3/4" Door Contact Sensor hole in the edge of the door for the correct door thickness.

Carefully remove the template.

6. MARK "DOOR CONTACT MAGNET" ON JAMB

The Door Contact Magnet must be installed in the door jamb such that when the door is closed, the Door Contact Sen-

sor is located directly opposite the Magnet. Install as follows:

6A.Open the door and temporarily place a piece of tape across the center of the mark made for the Door Contact

Sensor in the previous step. This tape signifies the height (from the floor) of the Door Contact Sensor.

6B.Close the door. Transfer this height to the door jamb with a light pencil mark.

6C.Determine the center location on the jamb directly opposite the Door Contact Sensor when the door is closed.

Open the door and measure the distance from the door edge to the center of the Door Contact Sensor (0.875"

or ⅞"). Transfer this distance to the door jamb, measured from the door stop.

FIG. 5: DOOR CONTACT SENSOR HOLE

ON DOOR EDGE

FIG. 5A: SELECT HOLE FOR DOOR THICKNESS

FIG. 6B: CLOSE DOOR AND

TRANSFER HEIGHT TO JAMB

FIG. 6A: TAPE SIGNIFIES

"HEIGHT FROM FLOOR" FIG. 6C: LOCATE MAGNET IN JAMB

CENTERED DIRECTLY OPPOSITE THE

SENSOR WHEN DOOR IS CLOSED

ArchiTech Cylindrical Lock & Surface-Mounted Networx Control Unit Mounting and Installation Instructions

7. TAPE ON DOOR: "SURFACE-MOUNTED NETWORX CONTROL UNIT"

TEMPLATE (WI2099)

The Surface-Mounted Networx Control Unit (see Fig. A on page 1) is al-

ways mounted on the inside ("protected") door surface.

Fold and place the template (WI2099) on the inside door edge. Align the

template with the "HORIZONTAL CENTER LINE OF LEVER" and the 5/8"

diameter thru-hole as shown on the template. Tape the template in place.

8. MARK TEMPLATE "SURFACE-MOUNTED NETWORX CONTROL UNIT" HOLES

On the inside ("protected") door surface, mark the two Control Unit Mounting Plate (Fig. 8) holes using the correct mark-

ings printed on the template (if door is beveled, use correct markings for beveled doors as described in step 1).

The center of the 5/8" diameter thru-hole was already marked on the outside surface in step 4; for the inside door sur-

face, mark the center of the 5/8" diameter thru-hole. This 5/8" diameter thru-hole is used for the Cylindrical Lock Motor

Wire, Proximity Reader and Door Contact Sensor wires.

Carefully remove the template.

FIG. 7: EXAMPLE OF INSIDE

DOOR EDGE (ARROW)

FIG. 8: MARK THE TWO "CONTROL UNIT

MOUNTING PLATE" HOLES (ARROWS)

ArchiTech Cylindrical Lock & Surface-Mounted Networx Control Unit Mounting and Installation Instructions

DOOR PREP: DRILL HOLES

IMPORTANT: Remove all burrs from wire holes. Sharp edges can eventually wear away wire insulation.

9. DRILL THE FOLLOWING HOLES IN THE DOOR

9A. Use 7/64" drill bit:

On the outside ("unprotected side")

door surface, drill the two pilot

holes for the Proximity Reader

mounting screws (NOT thru-holes,

drill only into the door surface).

9B. Use 7/64" drill bit:

On the inside ("protected side")

door surface, drill the two pilot

holes for the Control Unit Mounting

Plate mounting screws (NOT

thru-holes). Drill only into the in-

side door surface.

9C. Use 5/8" drill bit: 5/8"diameter thru-hole.

Drill straight through the door.

9D. Use 3/4" drill bit: 3/4" Door Contact

Sensor hole in edge of the door

(for solid wood doors, drill until the

hole intersects with the 5/8" diameter

thru-hole).

FIG. 9A: 7/64" PILOT HOLE ON

OUTSIDE DOOR SURFACE FOR

PROXIMITY READER

FIG. 9B: 7/64" PILOT HOLE ON

INSIDE DOOR SURFACE FOR

CONTROL UNIT PLATE

FIG. 9C:

5/8" DIAMETER THRU-HOLE

(5/8" DIAMETER

THRU-HOLE,

DRILLED IN

STEP 9C)

(CYLINDRICAL

LOCK PREP,

STEP 2)

"DOOR CONTACT SENSOR" HOLE

(3/4") IN EDGE OF DOOR

FIG. 9D: 3/4" DOOR CONTACT SENSOR HOLE IN EDGE OF THE DOOR

ArchiTech Cylindrical Lock & Surface-Mounted Networx Control Unit Mounting and Installation Instructions

10. DRILL "DOOR CONTACT MAGNET" HOLE IN JAMB

10A. Find the Door Contact Magnet. The type provided will be either Type A or Type B (see image below). For the

type provided, note its dimensions in Fig. 10A.

10B. Drill into the door jamb as follows:

For Hardwood Jambs:

 For the thicker "Type A" contact (below left image): Drill a 3/4" hole 7/8" deep into the jamb (marked in

step 6).

 For the thinner "Type B" contact (below right image): Drill a 3/8" hole 7/8" deep into the jamb (marked

in step 6).

For Hollow Metal Jambs:

 Use either a 3/4" or 3/8" bit (depending on Door Contact Magnet Type A or Type B) to drill a hole into the sur-

face of the jamb.

10C. Insert the magnetic Door Contact Magnet in the jamb hole; the contact sits almost flush with the jamb when fully

inserted. In some cases, an adhesive may be needed to ensure a secure fit.

FIG. 10A: FIND THE "DOOR CONTACT MAGNET" PROVIDED, EITHER

TYPE A (3/4" DIAMETER) OR TYPE B (3/8" DIAMETER)

Φ31/32" Φ7/16"

Type A (3/4" dia.) Type B (3/8" dia.)

FIG. 10B: DRILL DOOR JAMB HOLE

(EITHER 3/8" OR 3/4" DEPENDING

ON TYPE)

FIG. 10C: DOOR CONTACT MAGNET

INSTALLED IN DOOR JAMB

ArchiTech Cylindrical Lock & Surface-Mounted Networx Control Unit Mounting and Installation Instructions

DECISION: HOW TO ROUTE THE CYLINDRICAL LOCK MOTOR WIRE?

The Cylindrical Lock Body includes a Cylindrical Lock Motor Wire plug that must be

routed to and plugged into the Surface-Mounted Networx Control Unit.

HOW this Motor Wire is routed depends on whether the door is solid or hollow, and

whether you choose to use the Wiring Plate HW1945 (wires routed behind plate) or

the Cylindrical Drill Jig part #N90S1DJ (wires routed through door).

Hollow Metal Doors:

 Option 1: (Easiest option) Route the Cylindrical Lock Motor Wire

within the hollow metal door. Skip to step 12E on page 13.

 Option 2: If for some reason you do not wish to run wires through a

hollow metal door, route the Cylindrical Lock Motor Wire behind the Wir-

ing Plate (HW1945). The wire runs along one of its inside grooves

that, when installed, rests against the inside door surface. Skip to step

11.

Solid Wood Doors:

 Option 1: Route the Cylindrical Lock Motor Wire behind the Wiring

Plate (HW1945) along one of its grooves that, when installed, rests

against the inside door surface. Skip to step 11.

 Option 2: If you do not wish to use the Wiring Plate, use the Cylin-

drical Drill Jig (part #N90S1DJ) to drill a pathway for the wire within

the solid wood door (from the 2-1/8" diameter door chassis hole to the

5/8" diameter thru-hole). Skip to step 12.

FIG. B: SELECT A METHOD TO

ROUTE THE LOCK WIRE

WIRING

PLATE

(HW1945)

CYLINDRICAL

DRILL JIG

(N90S1DJ)

ArchiTech Cylindrical Lock & Surface-Mounted Networx Control Unit Mounting and Installation Instructions

11. USING THE WIRING PLATE

The Wiring Plate is always installed on the inside ("protected") side door surface. Note also that the Cylindrical Lock

Body motor wire will run along the inside ("protected") side door surface.

11A. Install the latch and secure with screws provided.

11B. From the outside ("unprotected") side of the door, insert the

Cylindrical Lock Body into the 2-1/8" diameter door chas-

sis hole (standard ASA 161 door prep) as detailed in its in-

stallation instructions provided with the unit.

IMPORTANT: Ensure the Cylindrical Lock Motor Wire

runs to the inside ("protected") side of the door. Do not in-

stall the inside housing yet, as the Wiring Plate will need to

be installed first.

FIG. 11B: WIRE RUNS TO THE INSIDE

FIG. 11A: INSTALL LATCH

ArchiTech Cylindrical Lock & Surface-Mounted Networx Control Unit Mounting and Installation Instructions

11C. Route the Cylindrical Lock Motor Wire within one of the two

grooves located on the "interior" of the Wiring Plate; use the

groove on the same side as the Motor Wire as it exits the Lock

Body. Tape the wire in place.

Note: The Cylindrical Lock Motor Wire plug sleeve color is

yellow.

11D. Place the circular opening of the Wiring Plate over the inside ("protected" side) so that its "interior" grooves will

rest against the inside door surface.

Use a level to ensure the Wiring Plate is vertical; use a pencil to mark its two mounting holes in the

door surface.

11E. Drill the two pilot holes for the Wiring Plate mounting screws (NOT thru-holes) using a 7/64" drill bit. Drill only

into the inside door surface (NOT thru-holes).

11F. Secure the Wiring Plate to the door using the two Phillips Flat Head screws appropriate for the door type as

follows:

 For Metal Doors: #6-32 x 5/8" long Type 23 thread

cutting Phillips Flat head, U-cut (part #SC682);

 For Wood Doors: #6 x 3/4" long undercut self-

tapping Type A Phillips head (part #SC596)

Skip to step 13.

FIG. 11C: USE THE GROOVE ON THE

SAME SIDE AS THE MOTOR WIRE

(ARROWS) FIG. 11CC: ROUTE THE MOTOR WIRE

WITHIN THE GROOVE CLOSEST TO THE

MOTOR WIRE. TAPE WIRE IN PLACE

Manuales populares de Cerradura de puerta de otras marcas

Assa Abloy

Assa Abloy effeff 827A-IP Manual de usuario

We.lock

We.lock SECBNEBL51 Manual de usuario

Iseo

Iseo MA1A Manual de usuario

ID Lock

ID Lock 150 Manual de usuario

Lockly

Lockly ACCESS TOUCH PRO Manual de usuario

iLoq

iLoq G50S Manual de usuario

SDC

SDC Z7835 Manual de usuario

ilco

ilco 452 Manual de usuario

Samsung

Samsung shs-h705 Manual de usuario

TRU-BOLT

TRU-BOLT 08102017 Manual de usuario

CDVI

CDVI 500-LADJ Manual de usuario

Igloohome

Igloohome Deadbolt 2S Metal Grey Instrucciones de instalación y mantenimiento

eSSL

eSSL FL-300 Manual de usuario

JAKO

JAKO JKBTNX4 Manual de usuario

Dorma

Dorma MUNDUS PREMIUM GK 50 Guía del usuario

SCOOP

SCOOP Pullbloc 4.1 FS Panik Manual de usuario

Yale

Yale MORTISE 8800 SERIES Manual de usuario

Siegenia

Siegenia KFV AS3500 Manual de usuario