Nemalux AR Series Manual de usuario

APPLICATION

AR luminaires are designed for use indoors, outdoors, wet locations, and areas containing moisture,

dirt, corrosion, vibration, and rough usage. NSF Models (ARxx-xxx-xx-xx-FS-XX) of the luminaire is

certied by NSF for use in Splash-zone and Non-Food areas of food processing locations as dened in

NSF-2. The AR luminaire is also certied for use on marine vessels inside, outside and in other severely

wet saltwater environments. Models ARXX-XXX-XX-XX-HZ-XX are certied for use in hazardous location

areas.

UL File Numbers: Nemalux General Location: E477827

Nemalux Hazardous Location: E477829

AR luminaires are suitable for use in the following areas as dened by the National Electrical Code

(NEC) and the Canadian Electrical Code (CEC):

Certications all models: UL 1598, UL 1598A and UL 8750;

CSA C22.2 No. 250.0 and CSA C22.2 No. 250.13

ABS Listed

Certications Hazardous Location models (ARXX-XXX-XX-XX-HZ-XX)

UL 844, CSA C22.2 No. 137

Hazardous Location Approved Locations:

Class I, Division 2, Groups ABCD, T4;

Class II, Division 2, Groups FG, T4A;

Class III;

Class I, Zone 2, Group IIC;

Zone 22

Certications NSF models (ARXX-XXX-XX-XX-FS-XX)

NSF/ANSI 2 Splash and Non-Food Zone

Housing: Copper-free Cast Aluminum with Polycarbonate lens

Input Voltage: Based on luminaire sux in table below: Sux - AC: 120-277 VAC | Sux - HV: 347-480

VAC

Inrush Current: AR (AC): Inrush Current Peak / >50% Duration 120V: 62A / 210uS 277V: 148A / 200uS

AR (HV): Inrush Current 347V: 118.4A / 97uS Peak / >50% Duration 480V: 148A / 79uS

Connections: 2 x 3/4”NPT Conduit | Black: Line | White: Neutral/Line 2 | Green: Ground

Optional: Violet (Purple): 0-10V Dimming (+) | Grey: 0-10V Dimming (-)

For connections use wire rated to a minimum of 90°C. Class 1 Wiring only.

Dimming control wires must be rated 300V minimum for luminaires with sux AC,

600V minimum for luminaires with sux HV.

Ingress Protection: IP66/67 | Suitable For Wet Locations. Marine Outside Type (Salt Water)

Nemalux

I N DUSTRIAL

AR Series

rev. A-30

1-16

www.nemalux.com | [email protected] | Tel 403•242•7475 | Fax 403•243•6190

MADE IN CANADA

Installation Spec Sheet Webpage

The AR Series Installation Manual

*White xture only

WARNING

ATTENTION

Potential Electrostatic Charging Hazard

Risque potentiel de charge électrostatique

Avoid electrostatic discharge :

• Clean exterior lens surface with damp cloth only

• Éviter les décharges électrostatiques: nettoyer la surface extérieure

de la lentille uniquement avec un chion humide

Nemalux

I N DUSTRIAL

AR Series

rev. A-30

2-16

www.nemalux.com | [email protected] | Tel 403•242•7475 | Fax 403•243•6190

MADE IN CANADA

Electrical Rating:

General Location (ARXX-XXX-XX-XX-GN-XX),

Food Safe (ARXX-XXX-XX-XX-FS-XX),

Hazardous Location (ARXX-XXX-XX-XX-HZ-XX)

APPLICATION CONT.

General Location High Intensity model

(ARXXH-XXX-XX-XX-GN-XX)

Temperature Range:

General Location (ARXX-XXX-XX-XX-GN-XX)

Food Safe (ARXX-XXX-XX-XX-FS-XX)

General Location High Intensity model

(ARXXH-XXX-XX-XX-GN-XX)

Hazardous Location (ARXX-XXX-XX-XX-HZ-XX)

LUMINANCE

AR10

AR15

AR20

AR25

AR30

RATED VOLTAGE

[Volts]

RATED WATTAGE

[Watts]

INPUT

VOLTAGE

120-277

347-480

120-277

347-480

120-277

347-480

120-277

347-480

120-277

347-480

107

129

145

190

187

247

248

312

310

FREQUENCY

[Hz]

50/60

LUMINANCE

AR20H

AR25H

AR30H

AR35H

AR40H

AR45H

AR50H

RATED VOLTAGE

[Volts]

RATED WATTAGE

[Watts]

INPUT

VOLTAGE

120-277

130

150

190

210

250

275

290

FREQUENCY

[Hz]

50/60

LUMINANCE

AR10, AR15,

AR20, AR25

AR30

AMBIENT TEMP

[°C]

INPUT

VOLTAGE

AC,HV Optical

AC Flood

HV Flood

-40 to 55

-40 to 50

-40 to 45

-40 to 40

-40 to 45

LUMINANCE

AR20H, AR25H

AR30H, AR40H

AR45H, AR50H

AMBIENT TEMP

[°C]

INPUT

VOLTAGE

-40 to 53

-40 to 48

-40 to 49

-40 to 40

-40 to 42

-40 to 40

LUMINANCE

AR10, AR15,

AR20

AR25

AR30

AMBIENT TEMP

[°C]

INPUT

VOLTAGE

-40 to 55

-40 to 54

-40 to 51

-40 to 44

-40 to 43

AMBIENT TEMP

[°C]

CLASS I, DIV 2

T-CODES

T3C

T3B

-40 to 55

-40 to 51

-40 to 55

-40 to 50

-40 to 42

-40 to 40

CLASS II, DIV 2

T-CODES

CLASS I, DIV 2

T-CODES

T4A

ALL MODELS

OPTICAL MODELS FLOOD MODELS

To reduce the risk of electric shock,

disconnect the luminaire from the

supply circuit before opening for

installation and servicing. Keep

tightly closed when in operation.

WARNING / ATTENTION

To avoid the risk of re, explosion,

or electric shock, this product

should be installed, inspected,

and maintained by a qualied

electrician only, in accordance

with all applicable electrical

codes.

Éviter tout risque d'incendie,

d'explosion ou d'électrocution, ce

produit doit être installé, inspecté et

entretenu par un électricien qualié

uniquement, conformément à tous

codes électriques applicables.

WARNING / ATTENTION

Pour réduire le risque de choc

électrique, débranchez le luminaire

du circuit d'alimentation avant

l'ouverture pour l'installation et

entretien. Gardez hermétiquement

fermé pendant le fonctionnement.

CURRENT

[A]

1.0A/0.5A

1.3A/0.6A

1.5A/0.7A

1.7A/0.8A

2.0A/0.9A

2.3A/1.0A

2.4A/1.0A

3-16

www.nemalux.com | [email protected] | Tel 403•242•7475 | Fax 403•243•6190

MADE IN CANADA

Nemalux

I N DUSTRIAL

AR Series

rev. A-30

5.0in

126mm

5.2in

132mm

21.1in

535mm

22.5in

570mm

0.5in

12.7mm

0.3in

6.8mm

0.5in

12.7mm

0.5in

12.7mm

0.5in

12.7mm

0.5in

12.7mm

STEP 1.

Inspect shipping package and contents to ensure no damage

has occurred during shipping.

STEP 2.

Remove 8x M6 hex cap bracket mounting screws from head

and re-install with included Surface/Suspension Mount

Brackets. See diagram for orientation of brackets. Torque M6

bolts to 5 Nm (45 in-lbs).

STEP 3.

A) For surface mounting conguration, mount luminaire in

desired ceiling location using 4x 1/4-20 OR 4x M6 fasteners

and washers (Not provided). One mounting hole on each

bracket is keyed to allow partial pre-installation of two

fasteners for ease of install.

B) For ceiling mounting congurations, connect 4x anchors to

the 12.7mm (0.5”) holes. Suspension hardware (Not provided)

must be rated for a minimum of 180 lbs.

STEP 4.

Open AR Lens with a 7mm socket or wrench and

allow Lens to hang via retention strap.

Note:

Screws are captive fasteners and will remain attached to the

Lens for ease of reinstall and to prevent loss of fasteners.

STEP 5.

Make wiring connections from branch circuit conductors to

factory provided lead wires. Refer to NEC/CEC codes and

follow all applicable local standards. See wiring diagram on

Page 4.

AR-SM – SURFACE/CEILING MOUNT INSTALLATION

(Ordered Separately)

(All brackets are ordered separately)

Refer to alternate instructions if using, Hook, Wall, Pole or Yoke Mount

Step 5

Step 2

Step 3A

Step 3B

WARNING:

The AR Head must not face

upwards by any degree

beyond the vertical position

for Class II, Division 2,

Zone 22, and Class III

hazardous locations.



LIGHT BEAM

HORIZON

ATTENTION:

Le luminaire (AR) ne doit pas

être orientée vers le haut de

quelque degré que ce soit

au-delà de la position verticale

pour les emplacements

dangereux de Classe II,

Division 2, Zone 22 et Classe III

4-16

www.nemalux.com | [email protected] | Tel 403•242•7475 | Fax 403•243•6190

MADE IN CANADA

Nemalux

I N DUSTRIAL

AR Series

rev. A-30

WIRING DIAGRAM

PS 1

PS 2

GROUND

(Factory)

BLACK  LINE

WHITE  NEUTRAL/LINE 2

GREEN  GROUND

VIOLET PURPLE  DIM +

GREY  DIM 

BLACK

WHITE

GREEN

VIOLET PURPLE

GREY

For 0-10V Analog Dimming Control, connect Violet (PURPLE) (+)

and Gray (-) to 0-10VDC control wiring:

• 0-10V Interface can be wired as Class 1 or Class 2

Circuit.

• LED Drivers will source a combined maximum of

400µA for control needs.

• 0-10V Controller must sink current from LED driver

0-10V control connections.

• Dimming controls must be certied and suitable

for the classication of the area of their installation

NOTE:

To aid in assembly and protection against ingress use of a

petrolatum or soap thickened mineral oil based thread

lubricant/sealant is necessary.

Un-used conduit opening must be plugged to maintain the

integrity of the enclosure.

STEP 6.

Close AR lens. Ensure the retention cable is not pinched between

AR Head and the AR Lens. Tighten lens bolts using a 7mm socket

or box wrench to 1.7 N-m (15 in-lbs) in the order designated in the

diagram to ensure gasket sealing. 5

Step 6

5-16

www.nemalux.com | [email protected] | Tel 403•242•7475 | Fax 403•243•6190

MADE IN CANADA

Nemalux

I N DUSTRIAL

AR Series

rev. A-30

AR-PM – POLE MOUNT INSTALLATION1(Ordered Separately)

Refer to alternate instructions if using Conduit, Hook, Wall, Yoke Mount, or High Vibration Yoke

INSTALLATION STEPS

Step 3

Step 5

STEP 1.

Inspect shipping package and contents to ensure no

damage has occurred during shipping. Discard

surface/ceiling mounting bracket provided with AR

luminaire. Remove 4 x M6 bolts from supply side of luminaire

and disard.

STEP 2.

Install the provided plastic 3/4”bushing into side 3/4" NPT

entry.

STEP 3.

Install Pole Mount and gasket with adhesive side applied to

mount using included M6 bolts and washers.

Torque to 5 Nm (45 in-lbs)

STEP 4.

Thread luminaire assembly onto 1-1/2” NPT pole.

NOTE:

To aid in assembly and protection against ingress use of a

petrolatum or soap thickened mineral oil based thread

lubricant/sealant is necessary.

Un-used conduit opening must be plugged to maintain the

integrity of the enclosure.

STEP 5.

Insert and tension M6 set screw to pole to lock rotation.

STEP 6.

Resume installation instructions provided with luminaire.

(STEP 4 in AR Installation Instructions provided with

Luminaire)

SET SCREW

This AR-PM kit is intended for use with UL Listed AR luminaire as

marked on the luminaire nameplate.

Accessory Package Contents

AR-PM

PART NAMEQTY

POLE MOUNT

POLE MOUNT GASKET

M6 X 25mm HEX HEAD CAP SCREW

M6 FLAT WASHER

M6 X 16mm HEX HEAD CAP SCREW

3/4 NPT THREADED SMOOTH BORE BUSHING

1-1/2" NPT Entry

WARNING:

The AR Head must not face

upwards by any degree

beyond the vertical position

for Class II, Division 2,

Zone 22, and Class III

hazardous locations.



LIGHT BEAM

HORIZON

ATTENTION:

Le luminaire (AR) ne doit pas

être orientée vers le haut de

quelque degré que ce soit

au-delà de la position verticale

pour les emplacements

dangereux de Classe II,

Division 2, Zone 22 et Classe III

6-16

www.nemalux.com | [email protected] | Tel 403•242•7475 | Fax 403•243•6190

MADE IN CANADA

Nemalux

I N DUSTRIAL

AR Series

rev. A-30

AR-WM – WALL MOUNT INSTALLATION (Ordered Separately)

Refer to alternate instructions if using Conduit, Hook, Pole, Yoke Mount, or High Vibration Yoke

STEP 1.

Inspect shipping package and contents to ensure no damage has occurred

during shipping. Discard surface/ceiling mounting bracket provided with AR

luminaire. Remove 4 x M6 bolts from supply side of luminaire and disard.

STEP 2.

Install provided 3/4 NPT conduit plugs in desired locations on wall mount.

To maintain ingress rating all NPT entries not used for wiring connections are

required to be plugged. Torque to 10 Nm (88 in-lbs)

NOTE:

To aid in assembly and protection against ingress use of a petrolatum or

soap thickened mineral oil based thread lubricant/sealant is necessary.

Un-used conduit opening must be plugged to maintain the integrity of the

enclosure.

STEP 3.

Install provided 3/4”NPT plastic bushing onto side NPT entry on AR head,

rotate so that ats are parallel to lens surface to avoid interference with

mount hardware.

STEP 4.

Install Wall Mount main body with included M6 bolts and washers and

adhesive backed gasket. Apply gasket to mount with adhesive backed side.

Torque to 5 Nm (45 in-lbs).

STEP 5.

Install Back Cover Plate with 4x M4 Flat head screws and adhesive backed

gasket. Apply gasket with adhesive side applied to mount main body.

Torque to 1.7 N-m (15 in-lbs).

STEP 6.

Mount luminaire assembly to desired location using

4x 1/4-20 OR M6 Screws or Bolts (Not Provided).

STEP 7.

Resume installation instructions provided with luminaire.

(STEP 4 in AR Installation Instructions provided with Luminaire)

Steps 2 through 5

[5.7in]

145mm

4 x

6.8mm THRU

ALL

[5.7in]

145mm

Step 6

This AR-WM kit is intended for use with UL Listed AR luminaire as

marked on the luminaire nameplate.

Accessory Package Contents

AR-WM

PART NAMEQTY

WALL MOUNT

WALL MOUNT PLATE

WALL MOUNT PLATE SIDE GASKET

WALL MOUNT GASKET

6 x 25mm SOCKET HEAD CAP SCREW

M4x 10mm FLAT HEAD SOCKET CAP SCREW

M6 FLAT WASHER

3/4 NPT HEX CAP PLUG

3/4 NPT THREADED SMOOTH BORE BUSHING

INSTALLATION STEPS

WARNING:

The AR Head must not face

upwards by any degree

beyond the vertical position

for Class II, Division 2,

Zone 22, and Class III

hazardous locations.



LIGHT BEAM

HORIZON

ATTENTION:

Le luminaire (AR) ne doit pas

être orientée vers le haut de

quelque degré que ce soit

au-delà de la position verticale

pour les emplacements

dangereux de Classe II,

Division 2, Zone 22 et Classe III

7-16

www.nemalux.com | [email protected] | Tel 403•242•7475 | Fax 403•243•6190

MADE IN CANADA

Nemalux

I N DUSTRIAL

AR Series

rev. A-30

WARNING:

The AR Head must not face

upwards by any degree

beyond the vertical position

for Class II, Division 2,

Zone 22, and Class III

hazardous locations.



LIGHT BEAM

HORIZON

ATTENTION:

Le luminaire (AR) ne doit pas

être orientée vers le haut de

quelque degré que ce soit

au-delà de la position verticale

pour les emplacements

dangereux de Classe II,

Division 2, Zone 22 et Classe III

AR-YM – YOKE MOUNT INSTALLATION (Ordered Separately)

Refer to alternate instructions if using Conduit, Hook, Pole, Wall Mount, or High Vibration Yoke

STEP 1.

Inspect shipping package and contents to ensure no damage has occurred

during shipping. Discard surface/ceiling mounting bracket provided with

AR luminaire. Remove 4 x M6 bolts from supply side of luminaire and

disard.

STEP 2.

Install suitable wiring system to the conduit opening per CEC/NEC

requirements for the specic location of install.

NOTE:

To aid in assembly and protection against ingress use of a petrolatum or

soap thickened mineral oil based thread lubricant/sealant is necessary.

Un-used conduit opening must be plugged to maintain the integrity of the

enclosure.

STEP 3.

Loosely assemble Yoke mount with carriage bolts on inside and washers

and nuts on the outside.

NOTE:

Depending on which mounting hole is used in the curved slot, the

luminaire may be congured for an upward or downward adjustable swing.

STEP 4.

Thread installed wiring through openings in yoke mount cheek plate and

yoke mount bracket. Mount yoke assembly to luminaire using 4x M6 Socket

Head Cap Screws and Washers (Provided). Torque fasteners to 5 Nm (45

in-lbs).

STEP 5.

Mount luminaire assembly to desired location using 4x 1/4-20 OR M6

Screws or Bolts (Not Provided).

STEP 6.

Adjust and aim luminaire to desired position. Torque hardware

nuts to 9 N-m (80 in-lbs).

STEP 7.

Resume installation instructions provided with luminaire.

(STEP 4 in AR Installation Instructions provided with Luminaire)

Step 5

Step 3

This AR-YM kit is intended for use with UL Listed AR luminaire as

marked on the luminaire nameplate.

Accessory Package Contents

INSTALLATION STEPS

AR-YM

PART NAMEQTY

YOKE MOUNT A

YOKE MOUNT B

CHEEK PLATE

1/4-20 HEX NUT

1/4" FLAT WASHER

1/4-20 x 0.5in CARRIAGE BOLT

M6 x 25mm HEX HEAD CAP SCREW

4.3in

108.15mm

2.3in

59mm

0.27in

6.76mm

0.27in

6.8mm

1.7in

44mm

2.8in

70mm

8-16

www.nemalux.com | [email protected] | Tel 403•242•7475 | Fax 403•243•6190

MADE IN CANADA

Nemalux

I N DUSTRIAL

AR Series

rev. A-30

AR-HK – HOOK PENDANT INSTALLATION (Ordered Separately)

Refer to alternate instructions if using Pendant, Wall, Pole, Yoke Mount, or High Vibration Yoke

Step 3

STEP 1.

Inspect shipping package and contents to ensure no damage has

occurred during shipping. Discard surface/ceiling mounting bracket

provided with AR luminaire.

STEP 2.

It is recommended to install Secondary Safety Cable by looping

appropriate steel cable or chain through the outer band of the unit and

fastening a closed loop. Secondary safety hardware must be rated for a

minimum of 180lbs. Secondary safety cables made from stainless steel

aircraft cable are available upon request.

STEP 3.

Slide anti-rotation lock onto suspension hook assembly and install hook

assembly into ¾ NPT threaded entry. Tighten to hand tight plus 1 to 2

turns. Slide anti-rotation lock into place and tighten set screw to lock unit

in place.

NOTE:

To aid in assembly and protection against ingress use of a petrolatum or

soap thickened mineral oil based thread lubricant/sealant is necessary.

Un-used conduit opening must be plugged to maintain the integrity of

the enclosure.

STEP 4.

Latch hook onto eye-bolt or other xed mounting loop. Mounting point

must be rated for a minimum of 180lbs.

STEP 5.

Install remaining loop of secondary safety chain or steel cable to suitable

mounting location and fasten securely.

STEP 6.

Resume installation instructions provided with luminaire. (STEP 4 in AR

Installation Instructions provided with Luminaire)

Step 2

This AR-HK kit is intended for use with UL Listed AR luminaire as

marked on the luminaire nameplate.

Accessory Package Contents

INSTALLATION STEPS

AR-HK

PART NAMEQTY

1PENDANT HOOK ASSEMBLY

ANTI-ROTATION ASSEMBLY

This kit contains NSF component Anti-Rotation-Lock

(1004-01-02-201)

9-16

www.nemalux.com | [email protected] | Tel 403•242•7475 | Fax 403•243•6190

MADE IN CANADA

Nemalux

I N DUSTRIAL

AR Series

rev. A-30

INSTALLATION STEPS

AR is Not permitted for conduit only

mounting when installed in hazardous

locations, additional mounting means

must also be utilized.

AR n'est pas autorisé pour le montage

sur conduit uniquement lorsqu'il est

installé dans des emplacements

dangereux, des moyens de montage

supplémentaires doivent également

être utilisés.

WARNING / ATTENTION

AR-CM –

CONDUIT MOUNT INSTALLATION

(Ordered Separately)

Refer to alternate instructions if using Wall, Hook, Pole or Yoke Mount

Step 2

STEP 1.

Inspect shipping package and contents to ensure no damage has

occurred during shipping. Discard surface/ceiling mounting bracket

provided with AR luminaire.

STEP 2.

Slide anti-rotation lock onto suitably mounted hanging conduit or

luminaire hanger and install luminaire onto ¾”NPT threaded nipple.

Tighten to hand tight contact plus 1 to 2 turns. Slide anti-rotation lock

into place and tighten set screw to lock unit in place. Fixed Rigid Metal

Conduit must be suitably mounted to prevent rotation and system must

be rated for 180 lbs.

NOTE:

To aid in assembly and protection against ingress use of a petrolatum or

soap thickened mineral oil based thread lubricant/sealant is necessary.

Un-used conduit opening must be plugged to maintain the integrity of

the enclosure.

STEP 3.

Install Secondary Safety Cable by looping appropriate steel cable or chain

through the outer band of the unit and fastening a closed loop.

Secondary safety hardware must be rated for a minimum of 180lbs.

Install remaining loop of secondary safety chain or steel cable to suitable

mounting location and fasten securely. Secondary safety hardware must

be rated for 180lbs.

STEP 4.

Resume installation instructions provided with luminaire. (STEP 4 in AR

Installation Instructions provided with Luminaire)

Step 3

This AR-CM kit is intended for use with UL Listed AR luminaire as

marked on the luminaire nameplate.

Accessory Package Contents

AR-CM

PART NAMEQTY

1ANTI-ROTATION BRACKET ASSEMBLY

WARNING:

The AR Head must not face

upwards by any degree

beyond the vertical position

for Class II, Division 2,

Zone 22, and Class III

hazardous locations.



LIGHT BEAM

HORIZON

ATTENTION:

Le luminaire (AR) ne doit pas

être orientée vers le haut de

quelque degré que ce soit

au-delà de la position verticale

pour les emplacements

dangereux de Classe II,

Division 2, Zone 22 et Classe III

10-16

www.nemalux.com | [email protected] | Tel 403•242•7475 | Fax 403•243•6190

MADE IN CANADA

Nemalux

I N DUSTRIAL

AR Series

rev. A-30

WARNING:

The AR Head must not face

upwards by any degree

beyond the vertical position

for Class II, Division 2,

Zone 22, and Class III

hazardous locations.



LIGHT BEAM

HORIZON

ATTENTION:

Le luminaire (AR) ne doit pas

être orientée vers le haut de

quelque degré que ce soit

au-delà de la position verticale

pour les emplacements

dangereux de Classe II,

Division 2, Zone 22 et Classe III

INSTALLATION STEPS

AR-YK – HIGH VIBRATION YOKE INSTALLATION (Ordered Separately)

Refer to alternate instructions if using Conduit, Hook, Pole, Wall Mount, or Yoke Mount

STEP 1.

Inspect shipping package and contents to ensure no damage has

occurred during shipping. Discard surface/ceiling mounting bracket

provided with AR luminaire. Remove 8 x M6 hex bolts from sides of

luminaire and discard.

STEP 2.

Mount AR high vibration yoke to mounting surface using a minimum of

4x ¼-20 or M6 fasteners (not provided).

STEP 3.

Install suitable wiring system to the conduit opening per CEC/NEC

requirements for the speci-c location of install.

NOTE:

To aid in assembly and protection against ingress use of a petrolatum or

soap thickened mineral oil based thread lubricant/sealant is necessary.

Un-used conduit opening must be plugged to maintain the integrity of

the enclosure.

STEP 4.

Mount AR Cheek Plates to sides of AR luminaire using 4x M6 at head cap

screws per side. Thread one cheek plate over installed wiring during

assembly. Torque fasteners to 5 Nm (45 in-lbs).

STEP 5.

Thread installed wiring through opening in AR high vibration yoke mount

and install AR luminaire into yoke. The raised circular bosses on the AR

cheek plates should register inside of the large circular holes on the AR

high vibration yoke mount arms. Rotate luminaire to aim in the desired

direction and fasten in place using 2x M6 socket head cap screws and at

washers per side. Torque fasteners to 5 Nm (45 in-lbs).

STEP 6.

Resume installation instructions provided with luminaire.

(STEP 4 in AR Installation Instructions provided with Luminaire)

Step 4

Step 2

This AR-YK kit is intended for use with UL Listed AR

luminaire as marked on the luminaire nameplate.

Accessory Package Contents

AR-YK

PART NAMEQTY

AR HIGH VIBRATION YOKE

CHEEK PLATE

M6 x 1 x 25mm SOCKET FLAT HEAD CAP SCREW

M6 FLAT WASHER

M6 x 1 x 16mm SOCKET HEAD CAP SCREW

8.0in

3.8in

203mm

95mm

2.3in 3.1in

59mm

4.3in

80mm

8.0in

108mm

203mm

0.3in

10 x

6.8mm

THRU ALL

Este manual sirve para los siguientes modelos

Otros manuales de Equipo de iluminación de Nemalux

Nemalux

Nemalux RH-20 Series Manual de usuario

Nemalux

Nemalux LS Series Manual de usuario

Nemalux

Nemalux RL Series Manual de usuario

Nemalux

Nemalux ZLM Manual de usuario

Nemalux

Nemalux RB Series Manual de usuario

Nemalux

Nemalux XR-GEN Series Manual de instrucciones de instalación

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario