NEC WT600 Series Guía de referencia rápida

NEC NEC Solutions (America), Inc.

VisualSystems

WhitePaper v1.0

WT600 Used In Rear Projection Systems

The WT600 has a very short throw distance that makes it an attractive product to use in a rear projection (RP) system.

By using the WT600, the depth of the rear projection system can be reduced by half of a system using a traditional

projector. It is possible to design a system with a 100” diagonal screen that has a total depth of approximately 24”

(single mirror system).

The key to using the WT600 in a rear projection system is ‘screen selection’.

The WT600 has a very steep projection angle (55°).

When the WT600 is installed on the opposite side of the screen from the viewer in an RP system, the image path

comes through the screen at a very steep angle. When the light path passes through the screen, the screen diffuses

much of the light so that the image can be seen from many angles. However some of the light keeps traveling at that

steep angle after it passes through the screen and keeps traveling up so that some light may pass over the viewers’

head when the projector is installed in desktop orientation. This portion of light is lost to the viewer (see diagram below).

55°

DIFFUSED

LIGHT

SOME LOST LIGHT

‘Hot spotting’ can also occur in areas on the screen, usually noticed at the very bottom of the screen in the middle,

when the projector is installed in desktop orientation. This is also dependant on the height of the viewer’s seating. In

testing the WT600 in the environments described, we have found the location of hot spotting and the intensity is not

very noticeable compared to a traditional projector with a rear lens where hot spotting tends to happen more around the

center of the screen and usually at more intensity.

Designers of RP Systems are also careful to use a screen and system designed to avoid the possibility of ‘secondary

reflection’. Secondary reflection can occur when an RP system with mirrors is used. Often diffusion screens have a

shiny side which when facing the projector can reflect some light back to the mirror which in turn will reflect back onto

the screen a second time (see diagram). This can cause a double image to occur. Secondary reflections can be

www.necvisualsystems.com Page 1 of 2

avoided by mounting the screen with the diffusion side toward the projector and the shiny side toward the viewer. This

look has much the same luster as a direct view TV. If a more matt surface is desired, screen manufacturers offer

screens with AR (anti-glare) coatings on the viewer side.

IMAGE HITS

SCREEN TWICE

MIRROR

A screen that will give the best results should be a ‘diffusion type’ and it should be installed so that the diffusion side is

facing the projector (not the viewer) to minimize the possibility of secondary reflection. Screens with a fresnel or ‘etched’

rear surface cannot be used since they require a projector with a zero degree offset lens. The WT600 does not have a

lens, and as stated earlier, the image is projected at a very steep angle (55°).

A diffusion screen with a low gain of approximately 1.0 should be used. A low gain will help to ‘capture’ the image within

the depth of the screen material and not allow much light to pass through and be lost over the viewer’s head, as well as

reduce the amount of hot spotting.

The system will not be as bright as when used with some brighter traditional projectors, and there may be some

minimal hot spotting at the bottom of the screen. However the pros should far outweigh the cons for many users who

need minimal depth in an RP system.

It is also very important that the integrator work with a screen manufacturer who has the expertise in designing an RP

system that will give optimum performance when a WT600 is used within the system.

www.necvisualsystems.com Page 2 of 2

Otros manuales para WT600 Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Proyector de NEC

NEC

NEC iS8-2K Manual de usuario

NEC

NEC GT5000 Series Manual de usuario

NEC

NEC GT5000 Series Manual de usuario

NEC

NEC NP40 Manual de usuario

NEC

NEC NP-VE281 Manual de usuario

NEC

NEC VT470 Manual de usuario

NEC

NEC NP300 Series Manual de usuario

NEC

NEC MultiSync MT1055 Guía de instalación y uso

NEC

NEC DLP Cinema NP-NC1402L Manual de usuario

NEC

NEC NC1700L Manual de usuario

NEC

NEC NP300 Series Manual de usuario

NEC

NEC LT380 - MultiSync XGA LCD Projector Manual de usuario

NEC

NEC ME403U Manual de usuario

NEC

NEC VT676 Series Manual de usuario

NEC

NEC NP-UM330X Series Manual de usuario

NEC

NEC M403W Manual de usuario

NEC

NEC Nighthawk XT9000 Guía de instalación y uso

NEC

NEC MT1075 Series Manual de usuario

NEC

NEC NP-P350W Manual de usuario

NEC

NEC PG-6200 Manual de usuario

NEC

NEC EDUCATIONNEWSRELEASEFINAL2 Manual de usuario

NEC

NEC NP01LK Manual de usuario

NEC

NEC NP40 Manual de usuario

NEC

NEC MultiSync MT1055 Guía de instalación y uso

Manuales populares de Proyector de otras marcas

iEmmet

iEmmet MP-312 Manual de usuario

Epson

Epson VS400 Manual de usuario

Sony

Sony VPL-HS10 Marketing Specifications & Features Manual de usuario

Sony

Sony VPL-HW65ES Manual de servicio

Toshiba

Toshiba TLP-791U Manual de usuario

Philips

Philips LC1341 Guía de referencia

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manual de usuario

BenQ

BenQ SH753P Manual de usuario

Eiki

Eiki EK-623U series Manual de usuario

Epson

Epson PowerLite Pro Cinema 6020UB Manual de usuario

Epson

Epson PowerLite Home Cinema 705HD Manual de usuario

Christie

Christie LHD700 Manual de usuario

Navitar

Navitar FX Manual de usuario

InFocus

InFocus LitePro 560 Manual de usuario

Sony

Sony SRX-R815P Manual de usuario

Vivitar

Vivitar DP1500 X Manual de usuario

Acer

Acer C20 Series Manual de usuario

Asus

Asus ZenBeam Latte Manual de usuario