NEC X551UN-TMX4P Manual de usuario

NEC Display Solutions of America, Inc.

QIG-TMXP-55UN

X551UN-TMX4P Rev 1.0

Parts List

o(4) X551UN Displays

o(4) Overnight Onsite Service Warranties (ONSITE-55-17)

o(4) Peerless Pullout Wall Mounts (DS-VW765-LAND)

o(2) Custom Peerless Spacers (DS-VWS040)

o(4) 3m DVI-D to DVI-D M/M cables

o(1) 5m DVI-D to DVI-D M/M cable

o(3) 10m Null Modem to Null Modem F/F cables

o(1) IR/Remote Control Kit (KT-RC)

o(2) Overframe Bezel Kits (KT-55UN-OF)

o(2) Tripp Lite 6 Outlet Strip (ISOBar6)

NOTES:

oAny walls that this video wall solution is anchored to must be strong enough to support the displays and the

installation must be in accordance with any local building codes. All mounting apparatuses must make secure

contact to wooden studs.

oPlease read entire document before starting installation

NEC Display Solutions of America, Inc.

QIG-TMX-55UN

X551UN-TMX4P Rev 1.0

1. For mounting information, please refer to the Installation Instructions provided by Peerless

Manufacturing inside of the box of the DS-VW765-LAND mount units.

2. Connect the NEC displays using the included DVI cables and the integrated DVI

loopthrough connections on the bottom of each monitor. Note that the DVI connection

closest to the front of the display is the ‘in’ connection while the connection closest to the

wall is the ‘out’ connection.

The ideal cabling set up is shown below to match the ideal monitor ID configuration.

However, DVI daisy chaining can be done different ways and still yield the same results.

Note that the connections for each X551UN monitor are on the bottom of each display, not

the side as shown in the image below. It may be helpful to start wiring before mounting.

3. Connect the null modem cabling to each display. It is recommended to connect from

Display 1 to Display 2, from Display 2 to Display 3, and from Display 3 to Display 4. Note

that the null modem cable needed to run from the source computer to Display 1 is not

included in this bundle. This will need to be purchased separately to control the display

remotely over RS232. Also loop through the provided IR Remote control cables.

NEC Display Solutions of America, Inc.

QIG-TMX-55UN

X551UN-TMX4P Rev 1.0

4. Apply the OverFrame bezel kit to the video wall. Please follow instructions provided with kit

(KT-55UN-OF).

5. Screw the IR Receiver (KT-RC) directly to the outside of the video wall and plug it directly

into the IR In terminal of Display 1.

6. Set each monitor ID up individually through the ‘MULTI-DSP’ menu within the OSD. It’s

recommended that the ID’s go from left to right, with the ID No. 1 being in the top left corner.

Overframe Kit

IR In

RS232 In

RS232 Out

IR Out

NEC Display Solutions of America, Inc.

QIG-TMX-55UN

X551UN-TMX4P Rev 1.0

Note that after the ID’s are set, there are two different ways to communicate to each screen

via the IR Remote. If the setting for the ‘IR Control’ within the ‘MULTI-DSP’ menu is set to

‘Normal’, then the IR remote control cabling is being utilized for communication. In order to

communicate to each screen individually, hold down the ‘Remote ID Set’ button on the

remote control, tap the number of the ID that you want to communicate with, then release

the Remote ID Set button. To test if this was done correctly, press the MENU button and

the OSD should now only appear on the display in which the remote control is

corresponding to. Also, more information on this is located within the User’s Manual.

To communicate to each display over the RS232 connection, make sure that the first display

(monitor ID 1) has its IR control set to ‘Primary’, while all others are set to ‘Secondary’.

When this is set, press the ‘Display’ button and the Monitor ID and Target ID should come

up in the left corner of each screen. Use the [+] and [-] buttons on the remote to change the

Target ID to the desired display you wish to communicate with then press ‘Display’ again. If

the menu is then pressed, the OSD menu should appear on the screen of the desired ID.

7. Use the TileMatrix feature to setup the 2x2 Video Wall. The Tilematrix feature of the NEC

Display allows for one image to be expanded and displayed over a 2x2 Video Wall Setup.*

This is accessed through the OSD (On-Screen Display) Controls under the “MULTI-DSP”

main menu icon. Under the TileMatrix sub-menu, enable the feature and set the necessary

NEC Display Solutions of America, Inc.

QIG-TMX-55UN

X551UN-TMX4P Rev 1.0

parameters that match the 2x2 Video Wall setup. Note that this step will need to be

completed for each screen.

8. Select if TileComp is necessary for this application or not. TileComp works in tandem with

TileMatrix to compensate for the width of the tiled bezels in order to accurately display the

image. Click ‘YES’ on enable to display video wall. Note that this step will need to be

completed for each screen.

If you are experiencing issues with this setup, please call our Technical Support number at

(800) 632-4622

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Monitor de NEC

NEC

NEC MultiSync M751 Manual de usuario

NEC

NEC E222W - MultiSync - 22" LCD Monitor Manual de usuario

NEC

NEC MULTISYNC LCD1510+ Manual

NEC

NEC MultiSync PA231W Manual de usuario

NEC

NEC LED-06AF1 Manual de usuario

NEC

NEC PX-50XM4 Manual de usuario

NEC

NEC MultiSync EA305WMi Manual de usuario

NEC

NEC AccuSync LCD73V Manual de usuario

NEC

NEC NEC MultiSync LCD1850E LCD1850E LCD1850E Manual de usuario

NEC

NEC C SERIES Manual de usuario

NEC

NEC LCD2010 - MultiSync - 20.1" LCD Monitor Manual de usuario

NEC

NEC AccuSync LCD71VM Manual de usuario

NEC

NEC MultiSync P554 Manual de usuario

NEC

NEC MultiSync E1100+ Manual de usuario

NEC

NEC MultiSync XV17+ Manual de usuario

NEC

NEC LCD2190UXP - MultiSync - 21" LCD Monitor Manual de usuario

NEC

NEC MultiSync X462HB Manual de operación y mantenimiento

NEC

NEC AccuSync LCD4000e Guía del usuario

NEC

NEC MultiSync EA243WM Manual de usuario

NEC

NEC MultiSync P484 Manual de usuario

NEC

NEC MultiSync LCD1850DX Manual de usuario

NEC

NEC 42XM5 - PlasmaSync - 42" Plasma Panel Manual de usuario

NEC

NEC MD242C2 Manual del producto

NEC

NEC MultiSync LCD1970NX Manual de usuario

Manuales populares de Monitor de otras marcas

Linear Acoustic

Linear Acoustic LQ-1000 Manual de usuario

AOC

AOC I2579V Manual de usuario

Gateway

Gateway FPD1520 Manual de usuario

Furuno

Furuno Mu 120c Manual de usuario

Asus

Asus VB171D - 17" LCD Monitor Manual de usuario

Dell

Dell S2230MX Instrucciones de uso

Philips

Philips 107C64 Manual de usuario

Dell

Dell S2409WFP Manual de usuario

EverFocus

EverFocus EN-7517E Manual de usuario

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manual de usuario

Dell

Dell Precision 7680 Manual de instrucciones

LG 50PM1M - - 50" Plasma Panel Manual de usuario

Bosch

Bosch DDU 9 Manual de usuario

Acer

Acer A231HL Manual de usuario

Philips

Philips 86BDL4152T Manual de usuario

Emay

Emay SleepO2 Manual de usuario

IBM

IBM 6360 Instrucciones de instalación

LG M1950D-PZ Manual de usuario