Nautilus T9 Series Manual de funcionamiento

Preventative Maintenance Guide

Product Support Website: www.nautilus.com/support

Nautilus T9 Series Treadmills

Daily

• Inspect the power cord and wal[king belt for wear,

, Check the position of the walking belt. Verify it does not rub against the frame, Evenly space the be,It on the deck

within 0.25inches of each side rail. Adiust the bek if necessary.

• Check the optional side hand rails. Fasten them securely.

, Remove potential hazards from the treadmill area.

Cleaning

Clean the treadmill on a regular basis he_psto improve operation and increase component _ifespan.

Da i ly

• Keep the treadmi_ arid controller free of du_ and debris. Use a damp sponge to wipe the exteriors and walking bek.

Do not soak sudaces. DW all surfaces thoroughly.

Dry mop the deck under the belt onl[y.Do not add any lubricants--adding lubricants can ruin the proprietary friction-

control sudace. Do not use detergents or cleaning agents on any par of the deck. Do not let liquid enter the treadmill

or controller, if it does, have a NautiBs ÷ approved technician inspect and test the equipment for safety by a before

using it again.

WeeMy

• Elevate the treadmill to maximom incline and vacuum the floor under it. This prevents excess dust and di_ from

interfering with operation.

If using the magnetic key, check it for rust: If you see rust, replace the magneL Rust en the magnetic key causes

power-up problems.

Treadmill Integer

_ angerous voltages are present under the treadmill hood:. Use caution when performing service to the e]ectrica_

components under the hood.

Depending upon the treadmill environment, dust and or lint can accumu_ate under the hood. Clean the interior of the

treadmill by doing:

1. Turnthe treadmill circuit breaker off. Unplug the treadmill power cord.

2. Remove the two screws on the treadmill hood.

S.Lift off the hood,

4. Cban inside the unit.

5, Reinstal_the hood and the _o screws,

6. Plug in the trea@nill power cord end switch on the trea@ni_[ circuit breaker.

Do not ove_ighten the walking heft. Be not torque adj_stment screws beyond _ in@s {9 N-M}. 0ve_ightening

reduces the beff life and may damage the rolbr bearings.

Adjusting Belt Tension

Adiust the heft tension whenever the heft s_ipsor moves

unsteadily during operatiom

1.Loosen the _o adiustment bolts (See Rgore 1}.

2.With the w'a[k#_g bek loose, place two marks 35 inches

(89 cm} apa_ on each side of the heft near the edge,

The belt must be loose enough for you to move it from

side-to-side on the front or rear ro_ler(See Figure 2}.

3. Turn the adiusting bolts cbckwise in equa_amounts

until the marks are be_een S5o_q6 inches and 35°d16

inches a£art, Proper tension for the walking heft is

between .5%-.6%. This equaB six fu]_turns of each

adiustment heft from the point where the belt begins to

stretch.

NOTICE: #o not exceed 35o5/16inches,

4.Test the belt by running on the belt at about 4 mph.

Hold the handrail lightly arid resist the belt movement

with your feel

Bo not ose a_lyour weight to resist the beff movement.

Too much resistance applied too bng (more than two

seconds) may shut down the system. {Various error

messages show on the display if this occurs, Cycle

power to resume normal operation.)

5. ff you feel the boutslip on the,front rotle_, increase

the tension of each adjo£ment bolt by 1/2turn.

Then rete£. If you fee_the holt sli_ agai_s,check the

tensioner adiustmenL

Figere 1

Figure 2

Oonotcutthebe_t.Doingso can cause the rear rol_er to fall and snap the alignment pins on the end c:ap.

Adjusting Belt Tracking

Adiust the be_ttracking whenever the belt moves to one side

or the other. Stay off the bek when adiu_ments.

1.Sta_ the treadmill at minimum speed and grade.

2,Increase speed to 6 m#h. Make the following

2=1 If the belt moves to the right: turn the right

adia_ment bok 1/4-tam c_ockwise.

2=2 If the belt moves to the left: turn the _efl

adiu_ment bok 1/4°turn clockwise.

3. Run the treadmill for 5 mim_tes after making the initia_

adiustmenL Observe how the belt tracks. # the belt

continues to move away from the cente5 adiust the

apprepriat_ side untN propedy centered.

Nautilus U916/R916

Roati n÷ M aint÷nanc÷

Upon receiving your machine, use a soft, clean towel to wipe off the dust, which may have accumulated during shipping.

Your new machine will require minor assembly, Refer to the "lnsta]lation Instructions" section for details.

Cleaniag

1. DO NOT USE G_SS CL_NERS ORANY OTHERHOUSEHOLD CLEANERSON THE CONSOLE. C_eanthe console daily

with a water-dampened cloth and wipe dry after cleaning.

2. Clean the exterior of the machine daily using soap and water or a diluted, non-mineral 5ased househoN cleaner such

as Fanta_ic®,.

[n:spection

,Frame: Inq_ect the frame for any rust, bubN[ng, or paint chi#s during the weekIy cbaning. The,salt in perspiration

can damage the unpainted surfaces. Repair the damaged area with a touch-up paint kit purchased from Nautilus (call

Cu_omer Se_ice for order information).

Chat:king the Battery Charge

Using your multimeter, touch the red lead to the positive termina_ of the battew and the black lead to the negative

terminal.

2. If the voltage level is less than 6.1 VDC, charge the battery.

Rechargi N the Batt÷W Back-Up

The CommerciaF Series U916 and R916 bikes are both self-powered (cordless)with a rechargeable batteW back-up.

Typically, the bike can be operated without Nugging in the battery charger. If, however,, the console flickers during

o#eration or the console disNay does not _igN u# while using the machine, then use the battew charger to recharge the

batteW back-up.

The bakery charger is suf_Nied with the unit and plugs into a standard 115 volt, 15 amp outlet, or a 220 volt, 15 amp outlet.

{A[[ maior voltage Nugs are available.} The Nug-in for the battery charger is located

in the front of the machine at the base.

NOTE: If in.ailing the optiona_ LCD Monito5 refer to the NV915 installation manual at

this time.

Plug the wail pack battew charger into the connector and charge the bakery for

approximatNy 24 hours and then recheck it. it is okay to use the machine while the

battery charger is connected.

When the bike is net connected to an external power source, the console will power

on as the user starts to pedal machine, and wil_ stay lit for up to 60 seconds in pause

mode. The consNe wil_ power off a_er 60 seconds of stopping exercise.

Bakery charger plug-in

If the bike is connected to an externa_ power source, the console will power on automatically and stay on until power is

disconnected.

Nautilus E916 Elliptical

Upon receiving your machine, use a soft, clean towel to wipe off the dust, which

may have accumulated during shippingo Your new machine will require, minor

assembly. Refer te theqnstaLlation Instructions" section for details.

Cleaning

=DO NOT USE GLASS CLEANERS ORANY OTHERHOUSEHOLD CLEANERS

ONTHE CONSOLE. Clean the console daily with a water-dampened c_oth and

wipe dry after cbaning.

2. Clean the exterior of the machine daity using soap and water or a diluted,

nonomineral based househokt c_eaner such as Fantastic@.

inspection

Frame: Inspect the frame for any rust, bubNing, or paint chips during the

weekly cleaning. The salt in perspiration can damage the unpainted surfaces.

Repair the damaged area with atouch-up paint kit purchased from NautiNs

{call Customer Service for order information).

C ecki g the B :cryCBa ge

1. Using your multimeter, touch the red _ead to the positive terminal of the

battery and the black lead to the negative terminal

2. If the voltage [eve_is [ess than &1 VDC, charge the battery.

th® Bal:1e yBacko J l}

The Cemmercia_ Series EV918arid E916e4@tica_are both self=powered

(cordless) with a rechargeable battery back=up.Typica!ly, the elliptical can

be operated without #lugging in the battery charger. If, however, the console

flickers during operation or the console dis#lay does not _ightup whi_e using the

machine, then usethe battery charger to recharge the battery back-up.

The battery charger is supplied with the unit and plugs into a standard 115volt,

15amp outlet. (all maiorvo]tage p_ugsare available} The plug-in for the battery

charger is located in the rear of the machine atthe base.

EV9.16/E9.16battery charger plug

Hug the wall pack battery charger into the co_nector at_dcharge the battery for

approximately 24 hours and then recheck it. It is okay to use the machine whi4e

the battery charger is connected.

The consote wilt power on as user starts to pedal machine, and wi41stay _itfor

up to 60 seconds in pa_se mode. The console will powe[ off after 60 seconds of

stop#ing exercise.

Nautilus Strength

1. UPHOLSTERVCLERI',IINGRHD PROTE_iOH

A. Keep pads free of perspiration at all times.

B. Clean and disinfect upholstery at the end of each

da)_ especially areas where [. e_oplrat_on and scalp

C. Clean all outside surfaces with non-abrasive, non-

chlorinated household cleaners.. Nautilus

Dish-ffectant Cleaner is an effective upholstery care

2. CLENNiNG NND CRREOF PRINTED

$UflFNCES

A. Wipe painted surfaces with a

damp clotl_ and car wax.

B. Let dry and buff with a dry

cloth.

3. CLENHING RND CRF_EOF fiBS PLNSTIC

SHIELDING

A_ Clean with non-abrasive, non-

chlorinated household cleaners.

B. Vacuum or wipe dust from

recessed areas and surfaces

QUIK FILL A-3 3

Detergen_Dis[n[ectant Odor Counteractant

MOVING PRRTS

A. To clean and lubricate guide rods, apply TFL#50

Wet Lubricant to a clean cloth then use to wipe

*TFL 50

Wet:

Lubricant

Recommended

for Nautilus

Machines_

Stairmaster ClubTrack 2100 Series Treadmills

£outine Maintenance Schedules

Performing reutine maintenance will help prevent unnecessaw wear to the treadmill and!or injuw to the user.The

maintenance schedules are meant only to seP_eas a guide_Dependingon where and how the treadmill is being

used,more frequent routine maintenance may be required

Daily

• Inspect the powe_cord and walking belt for wear.

• Checkthe position of the walking be_t Verify it is not rubbing against the ffame_The belt shoul{dbe evenly

spaced on the deck within 0,25 inches Adjsst the belt if necessary_

,_ Checkthe optional side handrails to ensure they ala fastened securely,.

Removepotential hazards flora the treadmill area_

Keepingthe StairMasteP'2100LC/LEtreadmillcleanonaregularbasiswill helpto improveoperationandincrease

the lifespanof thecomponents

BBYMoPTHE BECK UNBEBTHEBELTONLY.BONOTADD

ANY LUBBICANTS_ABDING LUBRICANTS CAN RUIN THE

PROPRIETARY FR[CTION-CONTROL SUBFACE,

BO NOT USE BETEBGENT$ 0B CLEANING AGENTS ON ANY PART

OFTHE BECK.

DO NOT LET IUOUIB Et'JTERTHE TREADMILL OB CONTROLLEB. IF

iT DOES, THE EQUIPMENT MUST BE INSPECTED AND TESTED

FORSAFETY BY ASTAIRMASTEB%APPROVED TECHNICIAN

BEFOREIT CAN BE USEB AGAIN,

Daily ....................................................................................................................................................................................................................................

• Keep the treadmill and controller fi_e ddust and debris. Use a damp sponge to wipe the exteriors and walking

belt: do not soak sue'faces DWall surfaces thoroughly

Weekly

,, Elevatethe t_eadrnitlto maximumincline andvacuumthe floor underit to preventexcessdustanddi_ from

intedering with operation,

• If the magnetickeyisbeingused,checkit for rust, Ifyou detect rust,replacethe magnet Rustonthe magnetic

keywill causepower-upproblems

Tabla de contenidos

Otros manuales de Rueda de andar de Nautilus

Nautilus

Nautilus Sport Series T514 Manual de usuario

Nautilus

Nautilus Be Strong Commerical T916 Instrucciones de instalación y funcionamiento

Nautilus

Nautilus Be Strong Commerical T916 Manual de usuario

Nautilus

Nautilus T624 Manual de usuario

Nautilus

Nautilus Be Strong Commerical T914 Manual de usuario

Nautilus

Nautilus Be Strong Commerical T912 Manual de usuario

Nautilus

Nautilus T624 Manual de usuario

Nautilus

Nautilus 6 Series Manual de usuario

Nautilus

Nautilus T616 Manual de usuario

Nautilus

Nautilus Trimline T523 Manual de usuario

Nautilus

Nautilus T618 Manual de usuario

Nautilus

Nautilus Commercial Series TreadClimber TC916 Manual de usuario

Nautilus

Nautilus PRO SERIES TREADMILLS T7.14 Manual de usuario

Nautilus

Nautilus T7.18 Manual de usuario

Nautilus

Nautilus Sport Series Manual de usuario

Nautilus

Nautilus Commercial Series TreadClimber TC916 Manual de usuario

Nautilus

Nautilus Be Strong Commerical T914 Manual de servicio

Nautilus

Nautilus T626 Manual de usuario

Nautilus

Nautilus T618 Manual de usuario

Nautilus

Nautilus M-7001 A Manual de instalación y operación

Nautilus

Nautilus T618 Manual de usuario

Nautilus

Nautilus T684 Manual de usuario

Nautilus

Nautilus Be Strong Commerical T912 Manual de usuario

Nautilus

Nautilus Sport Series T514 Manual de usuario

Manuales populares de Rueda de andar de otras marcas

Treadly

Treadly TREADLY 2 Manual de usuario

HEALTH ONE

HEALTH ONE Walk Ro Manual de usuario

NordicTrack

NordicTrack NTL12941 Manual de usuario

NordicTrack

NordicTrack T7.5 S Manual de usuario

Gold's Gym

Gold's Gym ADVANTAGE GGTL12920 Manual de usuario

Merax

Merax MS282992 Manual de usuario

FYTTER

FYTTER RU-2SX Manual de usuario

Precor

Precor 903 Manual de usuario

FitLogic

FitLogic freewill d225 Manual de usuario

HOP-SPORT

HOP-SPORT ESTIMA HS-3200LB Manual de usuario

Horizon Fitness

Horizon Fitness Adventure 5 Plus Manual de usuario

Stamia

Stamia InMotion II Manual de usuario

Smooth Fitness

Smooth Fitness EVO 3i Manual de usuario

NordicTrack

NordicTrack NETL81810.0 Manual de usuario

Schwinn

Schwinn 830/Journey 8.0 Manual de usuario

Keys Fitness

Keys Fitness HealthTrainer HT-740T Manual de usuario

Spirit

Spirit XT8 Manual de usuario

NordicTrack

NordicTrack T 14.0 Treadmill Manual de usuario