Nauticomp 21-1210 Manual de usuario
Page 1 of 30
USER MANUAL
Glass Bridge Display
®
Models
21-1210 12.1” Dayligh Display
21-1510 15.0” Dayligh Display
21-1910 19.0” Dayligh Display
21-2110 21.3” Dayligh Display
22-1210 12.1” Sunligh Display
22-1510 15.0” Sunligh Display
22-1910 19.0” Sunligh Display
22-2110 21.3” Sunligh Display
Canadian
Headquarters:
Nauticomp Inc.
8 Callaghan Road
Lindsay, Ontario
Canada
K9 4R4
p: +1 705 328 2992
f: +1 705 328 2990
UK:
Nauticomp European Distribution
2 Mornington Place, Waterberry Drive
Waterlooville, Hants, PO7 7XX
P:+44 2392 247920
f: +44 2392 261959
United States: Nauticomp International
1200 NE 7
th
Avenue
Fort Lauderdale
Florida, United States
33304
p: +1 954 235 4875
f: +1-705-328-2990
URL: www.nauticomp.com E-Mail: sales@nauticomp.com
Page 2 of 30
TABLE OF CONTENTS
1 GENERAL
1.1 Forward 4
1.2 Display Description…………………………………………………………………………………………..4
1.3 Contents of the Package………………………………………………………………………………….. 5
1.4 Warnings…………………………………………………………………………………………………………6
1.5 Important Information…………………………………………………………………………………….. 6
2 INSTALLATION
2.1 Handling Precautions 7
2.2 Planning 7
2.3 Power Requirements 7
2.4 Grounding 8
2.5 DC Power Connections 8
2.6 Extending the Power Cable 8
2.7 Cable Runs 9
2.8 Display Location 9
2.9 EMC Guidelines……………………………………………………………………………………………… 10
2.10 Mechanical Installation – Display 11
2.11 Electrical Installation – Display……………………………………………………………………..... 12
2.12 Recommendations for GA/D I Source…………………………………………………………….14
2.13 Mechanical & Electrical Installation – GB Commander……………………………………….. 14
3 OPERATION
3.1 Primary Control Functions 15
3.2 Overview - Menu Mode 16
3.3 GB Commander Button Functions – Menu Mode 16
3.4 Picture Menu 17
3.5 Source Menu 18
3.6 Utilities Menu 19
4 MAINTENANCE
4.1 Routine Maintenance 22
4.2 EMC Servicing and Safety Guidelines 23
5 TROUBLESHOOTING
5.1 Common Symptoms and Possible Solutions 24
6 APPENDIX
6.1 Declaration of Conformity………………………………………………………………………………. 25
6.2 Warranty Certificate………………………………………………………………………………………. 26
6.3 Warranty Limitations……………………………………………………………………………………… 26
6.4 Return of Goods Information (RMA)………………………………………………………………… 27
6.5 Document Revision History…………………………………………………………………………….. 27
6.6 Contact Details……………………………………………………………………………………………… 28
6.7 Product Notes………………………………………………………………………………………………. 29
Page 3 of 30
1 GENERAL
1.1 Forward
Founded in 1997, Nauticomp Inc. based in Canada designs and manufactures the widest range of
watertight sunlight readable displays for worldwide markets. Nauticomp Inc. is a fully accredited ISO
9001:2000 Company with regional offices located in the United States of America and Europe.
With respect to product innovation, all Nauticomp Displays are constructed to meet NMEA6/IP67
standards associated with the industrial and marine markets. The Displays are easily integrated into
applications due to the use of industry standard interfaces and are designed to comply with the
communications standards CE: CISPR/ EN55022 & EN 60945.
In support of the above, we offer the added value of a global network of experienced Dealers and
Systems Integrators to ensure customer satisfaction.
Please carefully read and follow the procedures stated in this manual.
1. Display Description
Glass Bridge Displays
®
offer the largest display in the smallest housing, minimizing overall dimensions,
enabling multiple displays to be mounted and maximizing available space. The TFT LCD’s used in the
Glass Bridge Series range from 12.1” through to 21.3” in either Daylight or Sunlight readable variants.
Each display is fitted with interface circuits that allow it to be connected with up to eight (8) inputs
ranging from GA and D I to Composite ideo sources. The display can accept signals of lower
resolution, such as GA. These signals are scaled so that they are displayed full screen.
Along with conventional LCD brightness and contrast controls, the display has an advanced dynamic
brightness dimming technique, permitting full brightness to “Dim to Red” selectable at any brightness
which is typically employed during night-time operation at low backlight levels.
A unique but simple remote On Screen Display (OSD) user interface known as the GB Commander
allows the user to adjust a wide variety of display parameters if necessary. Once the parameters are
set they are stored in non-volatile EEPROM. This ensures that the set-up is retained after power is
switched off.
All Displays are designed for operation from an external regulated 12.1 DC supply.
Nauticomp offers a wide range of external power supplies to match the power consumption
requirements of individual applications – 12 DC, 24 DC & 110/230 AC.
Each Glass Bridge Display
®
is shipped with a 3 year limited warranty 100% parts and labour.
Page 4 of 30
1 GENERAL con inued
1.3 Contents of the Package
Each Display is shipped with:-
Description
Part Number
Qty
Remarks
Display - Power Cable 23-LTWPOW 1 Feed from Nauticomp Power Supply:
Display input 2pin (RED) connector – Length approx.
10’ (3m).
Display - Mounting Kit 23-GBHARDWARE 1 Kit X11 Fixing Bolts, Bolt Clips & Centering Plates.
These are to be used when securing the display into a
console.
G Commander 23-LTWGBCOMM 1 External 4 Button Controller complete with cable –
Control for Glass Bridge Display
®
(GREEN) connector.
Length 25’ (7.6m).
Note: X4 Nut/Washers for mounting included.
Power Supply 12.1 DC As Specified 1 Either: 12 DC, 24 DC or 115/230 AC
Standard Power Cable As Specified 1 Only supplied with AC Power supplies. Either:
US/UK/Euro Cord.
Length approx. 6’8” (2m).
Note: Cable not supplied with DC versions…
GA ideo Cable 23-LTW GA 2 Connects standard GA, Length approx. 10’ (3m).
Composite ideo Cable 23-LTWCOMPOSITE 1 3 into 1 Cable: Signal connector designation-X3
(YELLOW) Phono connectors. Composite 1 (BLUE) Wire,
Composite 2 (GREEN) Wire, Composite 3 (RED) Wire.
Display Input (YELLOW) connector.
Length approx. 10' (3m).
Composite ideo Cable 23-LTWCOMPOSITE
(white)
1
S- ideo 1 (WHITE) connector to Composite
Length approx. 10’ (3m).
D I ideo Cable 23-LTWD I 2 Connects standard D I, Length approx. 10’ (3m).
Blanking Plug Set 23-LTWCAPS 1 set X9 for covering unused connections.
User Manual GBManual Rev X 1 Installation & User Manual (Refer Section 8.5 for Rev)
Cut-Out (Paper) Kit As Specified 2 X1 Display & X1 GB Commander
Page 5 of 30
1 GENERAL con inued
1.4 Warnings
1.4.1
Product Installation:
This equipment must be installed and operated in accordance with
the Nauticomp instructions provided. Failure to do so could result in poor product performance,
personal injury and/or damage to connected items.
1.4.2
Electrical Safety:
Make sure you have switched off the power before you start installing
this product. The display unit contains high voltages. Adjustments require specialized service
procedures and tools only available to qualified service technicians. There are no user
serviceable parts or adjustments. The user should never attempt to service the equipment
doing so will void the products warranty.
1.4.3
Navigation Aid:
When this display is used within a navigation system, it is only an aid to
navigation. Its accuracy can be affected by many factors, including equipment failure or defects,
environmental conditions, and improper handling or use. It is the user’s responsibility to exercise
common prudence and navigational judgments. This unit should not be relied upon as a
substitute for such prudence and judgment. Always maintain a permanent watch so you can
respond to situations as they develop.
1.4.4
TFT Colour LCD Displays:
The colours of the Display may seem to vary when viewed
against a coloured background or in coloured light. This is a perfectly normal effect that will be
seen with all colour LCD displays. In common with all Thin Film Transistor (TFT) panels, the
screen may exhibit a few (less than 7) wrongly illuminated pixels. These may appear as black
pixels in a light portion of the screen, or as coloured pixels in black areas.
1.4.5
EMC Conformance:
The design and manufacture of Nauticomp equipment and
accessories conform to the appropriate Electromagnetic Compatibility (EMC) standards, but
correct installation is required to ensure that performance is not compromised. Nauticomp
displays are designed to comply with EN55022 Class A-Emission, EN 55024- Immunity Standards
& EN 60945.
1.4.6
Disposal: Waste Electrical and Electronic Equipment (WEEE) Directive
This Product complies with the WEEE directive (2002/96/EC) marking requirements.
The affixed label indicates that you must not discard this electrical/electronic product
in domestic household waste. To dispose of your Nauticomp electronic product,
please contact your local Nauticomp dealer, distributor, or the factory directly by
visiting www.nauticomp.com.
1.4.7
User Manual Content:
The technical and graphical information contained in this
handbook, to the best of our knowledge, was correct as it went to press. However, our policy of
continuous improvement and updating may change product specifications without prior notice.
As a result, unavoidable differences between the product and handbook may occur from time to
time. Nauticomp cannot accept liability for any inaccuracies or omissions it may contain.
1.5 Important Information
This User manual contains important information on the installation and operation of your new display. In order
to obtain the best results in operation and performance, please read this User Manual thoroughly. Nauticomp’s
Technical Service representatives or your local dealer will be available to answer any questions you may have.
Page 6 of 30
2 INSTALLATION
.1 Handling Precautions
The casing of the Display gives good protection to its internal components. To prevent damage to the
LCD Display, it is important to observe a few simple precautions.
2.1.1 Unpack your display carefully to prevent damage.
2.1.2 Save the carton and packing in case you need to return the Display for service.
2.1.3 If the surface is soiled, wipe lightly with clean absorbent cotton or other soft cloth.
2.1.4 The TFT panel and circuit boards contain devices that are sensitive to Electrostatic
Discharge. Adequate ESD precautions should be taken during unpacking, handling and
installation of the TFT monitor.
2.1.5 There are no user serviceable parts inside the monitor. All servicing must be carried
out by qualified personnel.
2.1.6 The casing should never be opened by unqualified personnel, as there are potentially
harmful voltages within this equipment.
. Planning
Before you install your Display, plan the installation considering:
2.2.1 Display location and mounting options.
2.2.2 Power requirements.
2.2.3 Cable runs do not run video cables near any AC power sources.
2.2.4 Additional components e.g. Glass Bridge Commander and peripheral devices.
.3 Power Requirements
The display requires an external, regulated, 12.1 DC power supply.
To meet onboard requirements, Nauticomp offers a wide range of external power supplies to match
the power consumption requirements of individual displays being – 12 DC, 24 DC, & 115/230 AC.
Page 7 of 30
2 INSTALLATION con inued
.4 Grounding
It is important that an effective RF ground is connected to the display. You must ground the display
by connecting the drain (earth) terminal directly on the Nauticomp power supply to the nearest RF
ground source (superstructure). The length should be as short as possible.
CAUTION:
This Display is not intended for use on ‘’Positive’ ground circuits. The power input cable Earth screen
connections must be connected directly to a RF ground source.
.5 DC Power Connections
The power connection to the Nauticomp Power Supply should be made at either the output of the
battery isolator switch, or at a DC power distribution panel. Nauticomp recommends that power be
fed directly to the Nauticomp Power Supply via its own dedicated cable system. An in-line fuse is
required to be installed on the positive (+) feed going to the Nauticomp provided power supply.
See table below for reference:-
Vessel Power Source Rating of Fuse
12 DC 10 Amp
24 DC 5 Amp
.6 Extending the Power Cable
Longer power cable runs may require larger wire gauges to minimize any voltage drop in the cable.
Ensure that the minimum voltage specification of the display is met at the junction of these cables
when the Display is operating at full brightness. If a longer power cable run is required, use the
supplied power cable to connect to the display unit. Then use a suitable connector block to connect
the free end to the extension cable; take particular care to ensure correct polarity and grounding of
the screening braid to an RF ground source. The supplied 3 meter power cable (Part # 23-LTWPOW)
has a cross-section of 16 AWG.
Page 8 of 30
2 INSTALLATION con inued
.7
Cable Runs
Consider the following before installing the Display:-
2.7.1 All cables should be adequately secured, protected from physical damage and
protected from exposure to heat. Avoid running cables through bilges or doorways, or
close to moving or hot objects.
2.7.2 Acute bends must be avoided.
2.7.3 Where a cable passes through an exposed bulkhead or deckhead, a watertight feed-
through should be used.
2.7.4 Make sure any excess cable is coiled and secured.
2.7.5 Do not run video cables near AC power sources or wires.
CAUTION:
Do not ‘Pull’ cables through the bulkheads, walls or tight spaces using a cord attached to the
connector. This could damage the connections.
.8 Display Location
2.8.1 Viewing angle: This LCD panel has been chosen to give the very best performance,
including viewing angle. However, the contrast and colours seen on all LCD displays
vary slightly with viewing angle.
Note:
iewing an LCD panel from the bottom angle (outside specified display viewing
angle characteristic) is typically unacceptable.
2.8.2 Access: There must be sufficient space behind the display to allow cable connections
to the rear connectors, avoiding tight bends in the cable. All connections are bottom
entry.
2.8.3 Interference: The selected location should be far enough away from devices that
may cause interference, such as motors, generators and radio transmitter/receivers
(see the EMC guidelines section 2.9).
2.8.4 Magnetic compass: Mount the display unit at least 3 ft (1m) away from a magnetic
compass.
2.8.4 Environment: To prevent overheating, do not restrict airflow at the front or rear of
the display unit; ensure there is adequate ventilation.
Page 9 of 30
2 INSTALLATION con inued
2.8.5 Heat Management: The display is designed to work within most high ambient heat
conditions. There are extreme yet rare conditions that may cause the display to go
black or “ Blackout ”. This is normally caused by concentrated and excessive U rays
(DIRECT SUNLIGHT) acting on the LCD panel.
To minimize the risk of the Display being subjected to the above one should endeavour
to:-
2.8.5.1 Employ additional cooling to assist with heat dissipation.
2.8.5.2 Provide additional shading.
.9
EMC Guidelines
All Nauticomp Displays and accessories are designed to the best industry standards for use in the
rugged electronic environment. The design and manufacture conforms to the appropriate
Electromagnetic Compatibility (EMC) standards (Section 1.4.5 refers), but correct installation is
required to ensure that performance is not compromised. Although every effort has been taken to
ensure that they will perform under all conditions, it is important to understand what factors could
affect the operation of the product. The guidelines given here describe the conditions for optimum
EMC performance, but it is recognized that it may not be possible to meet all of these conditions in all
situations. To ensure the best possible conditions for EMC performance within the constraints imposed
by any location, always ensure the maximum separation possible between different items of electrical
equipment.
For optimum EMC performance, it is recommended that where ever possible Nauticomp Displays and
cables connected should be:
2.9.1 At least 3 ft (1 m) from any equipment transmitting or cables carrying radio signals e.g.
HF radios, cables and antennas. In the case of SSB radios, the distance should be
increased to 7 ft (2 m).
2.9.2 More than 7 ft (2 m) from the path of a radar beam. A radar beam can normally be
assumed to spread above and below the radiating element.
2.9.3 Supplied from a separate battery from that used for engine start. oltage drops below
10 , and starter motor transients, can cause the equipment to reset and or cause the
loss of some information and may change the operating mode.
2.9.4 Used with Nauticomp specified cables. Cutting and rejoining (Splice) these cables can
compromise EMC performance and must be avoided.
NOTE:
If a suppression ferrite is attached to a cable; this ferrite should not be removed.
Page 10 of 30
2 INSTALLATION con inued
.10 Mechanical Installation - Display
2.10.1 Flush Mounting
Step 1 Leave protective film on LCD in place until completion of installation.
Step 2 Refer to the cut-out dimensions supplied in the package, make a cut-out in the
mounting location.
Step 3 Add a “Non Adhesive” Silicon sealant to interior cut-out perimeter.
Step 4 Place your Nauticomp Glass Bridge Display
®
into the cut-out.
Step 5 Install ‘Bolt Clips’ (x11) into slots located on the rear sides of the Display.
Above Illustration – Orientation of an ‘L’ shaped ‘Bolt Clip’ within slot located on the rear of the Display.
Step 6 Thread ‘Bolts’ (x11) into ‘Bolt Clips’ leaving enough gap between each ‘Bolt’ and
the console for ‘Centering Plates’ to be fitted (refer to Step 7 below).
Step 7 Insert ‘Centering Plates’ (x11) into the clearance gap between the Display and
the console and position under each ‘Bolt’. Evenly hand-tighten ALL bolts.
Step 8 Apply 2 Full TURNS to each ‘Bolt’ to secure Display – Maximum permitted
torque loading 20 in/lbs (2Nm).
Above Illustration - Installed ‘Bolt’, ‘L’ Shaped Bolt Clip & ‘Centering Plate’
CAUTION:
Over tightening bolts WILL cause damage to the display’s chassis frame.
Bolt
‘L’ Shaped Bolt Clip
Centering Plate
‘L’ Shaped Bolt Clip
Rear of Display
Este manual sirve para los siguientes modelos
7
Tabla de contenidos
Otros manuales de Monitor de Nauticomp
