National Instruments NI 9214 Manual de usuario

NI-9214

GETTING STARTED GUIDE

NI 9214

16 TC, ±78 mV, 24 Bit, 68 S/s Aggregate,

Isothermal Terminal Block

This document explains how to connect to the NI 9214.

Note Before you begin, complete the software and

hardware installation procedures in your chassis

documentation.

Note The guidelines in this document are specific to

the NI 9214. The other components in the system might

not meet the same safety ratings. Refer to the

documentation for each component in the system to

determine the safety and EMC ratings for the entire

system.

Safety Guidelines

Operate the NI 9214 only as described in this document.

Caution Do not operate the NI 9214 in a manner not

specified in this document. Product misuse can result in

a hazard. You can compromise the safety protection

built into the product if the product is damaged in any

way. If the product is damaged, return it to NI for

repair.

2| ni.com | NI 9214 Getting Started Guide

Hazardous Voltage This icon denotes a warning

advising you to take precautions to avoid electrical

shock.

Safety Guidelines for Hazardous Voltages

If hazardous voltages are connected to the device, take the

following precautions. A hazardous voltage is a voltage greater

than 42.4 Vpk voltage or 60 VDC to earth ground.

Caution Ensure that hazardous voltage wiring is

performed only by qualified personnel adhering to local

electrical standards.

Caution Do not mix hazardous voltage circuits and

human-accessible circuits on the same module.

Caution Ensure that devices and circuits connected to

the module are properly insulated from human contact.

Caution When module terminals are hazardous

voltage LIVE (>42.4 Vpk/60 VDC), you must ensure

that devices and circuits connected to the module are

properly insulated from human contact. You must use

the TB-9214 included with the NI 9214 to ensure that

the terminals are not accessible.

NI 9214 Getting Started Guide | © National Instruments | 3

Safety Voltages

Connect only voltages that are within the following limits:

Between any two terminals ±30 V maximum

Isolation

Channel-to-channel None

Channel-to-earth ground

Continuous 250 Vrms, Measurement

Category II

Withstand 2,300 Vrms, verified by a 5 s

dielectric withstand test

Measurement Category II is for measurements performed on

circuits directly connected to the electrical distribution system.

This category refers to local-level electrical distribution, such as

that provided by a standard wall outlet, for example, 115 V for

U.S. or 230 V for Europe.

Caution Do not connect the NI 9214 to signals or use

for measurements within Measurement Categories III

or IV.

4| ni.com | NI 9214 Getting Started Guide

Safety Guidelines for Hazardous Locations

The NI 9214 is suitable for use in Class I, Division 2, Groups A,

B, C, D, T4 hazardous locations; Class I, Zone 2, AEx nA IIC T4

and Ex nA IIC T4 hazardous locations; and nonhazardous

locations only. Follow these guidelines if you are installing the

NI 9214 in a potentially explosive environment. Not following

these guidelines may result in serious injury or death.

Caution Do not disconnect I/O-side wires or

connectors unless power has been switched off or the

area is known to be nonhazardous.

Caution Do not remove modules unless power has

been switched off or the area is known to be

nonhazardous.

Caution Substitution of components may impair

suitability for Class I, Division 2.

Caution For Division 2 and Zone 2 applications,

install the system in an enclosure rated to at least IP54

as defined by IEC/EN 60079-15.

NI 9214 Getting Started Guide | © National Instruments | 5

Caution For Division 2 and Zone 2 applications,

connected signals must be within the following limits.

Capacitance 0.2 µF maximum

Special Conditions for Hazardous Locations Use in

Europe and Internationally

The NI 9214 has been evaluated as Ex nA IIC T4 Gc equipment

under DEMKO Certificate No. 07 ATEX 0626664X and is

IECEx UL 14.0089X certified. Each NI 9214 is marked II 3G

and is suitable for use in Zone 2 hazardous locations, in ambient

temperatures of -40 °C ≤ Ta ≤ 70 °C. If you are using the NI 9214

in Gas Group IIC hazardous locations, you must use the device in

an NI chassis that has been evaluated as Ex nC IIC T4, Ex IIC

T4, Ex nA IIC T4, or Ex nL IIC T4 equipment.

Caution You must make sure that transient

disturbances do not exceed 140% of the rated voltage.

Caution The system shall only be used in an area of

not more than Pollution Degree 2, as defined in

IEC 60664-1.

6| ni.com | NI 9214 Getting Started Guide

Caution The system shall be mounted in an

ATEX/IECEx-certified enclosure with a minimum

ingress protection rating of at least IP54 as defined in

IEC/EN 60079-15.

Caution The enclosure must have a door or cover

accessible only by the use of a tool.

Electromagnetic Compatibility Guidelines

This product was tested and complies with the regulatory

requirements and limits for electromagnetic compatibility (EMC)

stated in the product specifications. These requirements and

limits provide reasonable protection against harmful interference

when the product is operated in the intended operational

electromagnetic environment.

This product is intended for use in industrial locations. However,

harmful interference may occur in some installations, when the

product is connected to a peripheral device or test object, or if the

product is used in residential or commercial areas. To minimize

interference with radio and television reception and prevent

unacceptable performance degradation, install and use this

NI 9214 Getting Started Guide | © National Instruments | 7

product in strict accordance with the instructions in the product

documentation.

Furthermore, any changes or modifications to the product not

expressly approved by National Instruments could void your

authority to operate it under your local regulatory rules.

Caution To ensure the specified EMC performance,

operate this product only with shielded cables and

accessories.

Special Conditions for Marine Applications

Some products are Lloyd’s Register (LR) Type Approved for

marine (shipboard) applications. To verify Lloyd’s Register

certification for a product, visit ni.com/certification and search

for the LR certificate, or look for the Lloyd’s Register mark on

the product.

Caution In order to meet the EMC requirements for

marine applications, install the product in a shielded

enclosure with shielded and/or filtered power and

input/output ports. In addition, take precautions when

designing, selecting, and installing measurement probes

8| ni.com | NI 9214 Getting Started Guide

and cables to ensure that the desired EMC performance

is attained.

Preparing the Environment

Ensure that the environment in which you are using the NI 9214

meets the following specifications.

Operating temperature

(IEC 60068-2-1, IEC 60068-2-2)

-40 °C to 70 °C

Operating humidity

(IEC 60068-2-78)

10% RH to 90% RH,

noncondensing

Pollution Degree 2

Maximum altitude 2,000 m

Indoor use only.

Note Refer to the device datasheet on ni.com/manuals

for complete specifications.

NI 9214 Getting Started Guide | © National Instruments | 9

Otros manuales para NI 9214

Tabla de contenidos

Otros manuales de Bloque de terminales de National Instruments

National Instruments

National Instruments VXI-TB-1303 Manual de usuario

National Instruments

National Instruments NI SCXI -1339 Manual de usuario

National Instruments

National Instruments SCXI-1317 Manual de usuario

National Instruments

National Instruments PXIe-2527 Manual de usuario

National Instruments

National Instruments NI TB-2631B Manual de usuario

National Instruments

National Instruments SCXI-1324 Manual de usuario

National Instruments

National Instruments TB-2643 Manual de usuario

National Instruments

National Instruments NI SCXI -1366 Manual de usuario

National Instruments

National Instruments NI TB-2642 Manual de usuario

National Instruments

National Instruments SCXI-1320 Manual de usuario

National Instruments

National Instruments SCXI -1305 Manual de usuario

National Instruments

National Instruments BNC-2111 Manual de usuario

National Instruments

National Instruments SCXI-1166 Manual de usuario

National Instruments

National Instruments SCXI-1327 Manual de usuario

National Instruments

National Instruments SCXI-1305 Manual de usuario

National Instruments

National Instruments TC-2095 Manual

National Instruments

National Instruments NI TB-2634 Manual de usuario

National Instruments

National Instruments NI TB-2630B Manual de usuario

National Instruments

National Instruments CB-27T Manual

National Instruments

National Instruments NI TB-2627 Manual de usuario

National Instruments

National Instruments TB-2627 Manual de usuario

National Instruments

National Instruments SCXI-1303 Manual de usuario

National Instruments

National Instruments SCXI-1300 Manual de usuario

National Instruments

National Instruments SCXI-1321 Manual de usuario

Manuales populares de Bloque de terminales de otras marcas

Russound

Russound EZB-1SC Manual de usuario

Siemens

Siemens MOBY FC 56 Manual de lista de piezas

Panasonic

Panasonic TY-FB8TA Manual de usuario

NI SCXI-1379 Manual de usuario

ABB

ABB ZLS924 Guía del usuario

Festo

Festo CPVSC1-EPR Series Manual de usuario

Festo

Festo CPV -GE-DN2-8 Manual de lista de piezas

Stahl

Stahl 8146/2 Manual de usuario

Crestron

Crestron CLT-1FAN4 Manual de usuario

Sony

Sony CBX-H11 Manual de usuario

Festo

Festo CPX-FB38 Manual de lista de piezas

Festo

Festo CPV -GE-ASI-8E8A-Z Series Manual de lista de piezas

Festo

Festo MPA-S Series Manual de lista de piezas

Hubbell

Hubbell BASETRAK PB2 Series Manual de usuario

Crestron

Crestron CLT-2DIM2 Manual de usuario

Omron

Omron XW2B-40J6-2B Manual de instrucciones

Festo

Festo CPV GE-IL Series Manual de lista de piezas

Lenz

Lenz XpressNet Digital plus LA152 Manual del propietario