National Instruments NI 9860 Manual de usuario

GETTING STARTED GUIDE

NI 9860

NI-XNET Hardware Selectable Interface

Français Deutsch 日本語 한국어 简体中文

ni.com/manuals

This document explains how to connect to the NI 9860.

Note Before you begin, complete the software and

hardware installation procedures in your chassis

documentation.

Note The guidelines in this document are specific to

the NI 9860. The other components in the system might

not meet the same safety ratings. Refer to the

documentation for each component in the system to

determine the safety and EMC ratings for the entire

system.

Safety Guidelines

Operate the NI 9860 only as described in this document.

Hot Surface This icon denotes that the component

may be hot. Touching this component may result in

bodily injury.

Caution Do not operate the NI 9860 in a manner not

specified in this document. Product misuse can result in

a hazard. You can compromise the safety protection

2| ni.com | NI 9860 Getting Started Guide

built into the product if the product is damaged in any

way. If the product is damaged, return it to NI for

repair.

Safety Guidelines for Hazardous Locations

The NI 9860 is suitable for use in Class I, Division 2, Groups A,

B, C, D, T4 hazardous locations; Class I, Zone 2, AEx nA IIC T4

and Ex nA IIC T4 hazardous locations; and nonhazardous

locations only. Follow these guidelines if you are installing the

NI 9860 in a potentially explosive environment. Not following

these guidelines may result in serious injury or death.

Caution Do not disconnect I/O-side wires or

connectors unless power has been switched off or the

area is known to be nonhazardous.

Caution Do not remove modules unless power has

been switched off or the area is known to be

nonhazardous.

Caution Substitution of components may impair

suitability for Class I, Division 2.

NI 9860 Getting Started Guide | © National Instruments | 3

Caution For Division 2 and Zone 2 applications,

install the system in an enclosure rated to at least IP54

as defined by IEC/EN 60079-15.

Special Conditions for Hazardous Locations Use in

Europe and Internationally

The NI 9860 has been evaluated as Ex nA IIC T4 Gc equipment

under DEMKO Certificate No. 12 ATEX 1202658X and is

IECEx 14.0089X certified. Each NI 9860 is marked II 3G and

is suitable for use in Zone 2 hazardous locations, in ambient

temperatures of -40 °C ≤ Ta ≤ 70 °C. If you are using the NI 9860

in Gas Group IIC hazardous locations, you must use the device in

an NI chassis that has been evaluated as Ex nC IIC T4, Ex IIC

T4, Ex nA IIC T4, or Ex nL IIC T4 equipment.

Caution You must make sure that transient

disturbances do not exceed 140% of the rated voltage.

Caution The system shall only be used in an area of

not more than Pollution Degree 2, as defined in

IEC 60664-1.

Caution The system shall be mounted in an

ATEX/IECEx-certified enclosure with a minimum

4| ni.com | NI 9860 Getting Started Guide

ingress protection rating of at least IP54 as defined in

IEC/EN 60079-15.

Caution The enclosure must have a door or cover

accessible only by the use of a tool.

Wiring the NI 9860

The NI 9860 has two ports for connecting to NI-XNET CAN/LIN

Transceiver Cables (required to connect to the CAN/LIN bus)

and a two-position connector for use with an external power

supply.

For more information about transceiver cables, refer to the

NI-XNET CAN/LIN Transceiver Cables page on ni.com.

The NI 9860 requires an external power supply of +9 to +30 V to

power the transceiver cables. Supply power to the NI 9860 VSUP

connector on the module front panel using the supplied power

cable. The exposed lead wires at the end of the power cable are

routed as follows: black wire—COM, red wire—VSUP. The

power cable lead wires may be daisy-chained to the controller

power port when the controller supply voltage is in the

appropriate range.

NI 9860 Getting Started Guide | © National Instruments | 5

Note Power on VSUP is required for transceiver cable

operation.

Note When using more than four transceiver cables

with your CompactRIO chassis, refer to the NI-XNET

CAN/LIN Transceiver Cables page on ni.com for

mounting guidelines to limit the thermal impact to your

CompactRIO system.

The following figure shows the NI 9860 with Port 1 connected to

an NI-XNET CAN HS/FD Transceiver Cable and the

two-position connector connected to the power cable. The breaks

in the cables represent additional cable length.

6| ni.com | NI 9860 Getting Started Guide

Figure 1. NI 9860 with Power and Transceiver Cables Attached

NI 9860 Hardware Overview

The NI 9860 is a two-port C-Series module based on the XNET

architecture. Users can choose the physical bus protocol by

plugging in the corresponding transceiver cable. The NI 9860

NI 9860 Getting Started Guide | © National Instruments | 7

supports hot-swapping of transceiver cables and can detect and

identify transceiver cable types.

For more information about transceiver cables, refer to the

NI-XNET CAN/LIN Transceiver Cables page on ni.com.

Figure 2. NI 9860 Hardware Overview

Ext Pwr

Supply

Required

Controller

COM

Vsup

Pwr Sup

Controller

Port 1

Port 2

Transceiver

Cable

Transceiver

Cable

8| ni.com | NI 9860 Getting Started Guide

Inserting and Removing the NI-XNET

Transceiver Cable

The NI-XNET Transceiver Cable connects to a host device with

an active latching connector. To connect the NI-XNET

Transceiver Cable to a host device, push the connector assembly

into the host receptacle until the internal latch snaps into position.

The latch emits an audible click when engaged. To remove the

NI-XNET Transceiver Cable, push the lock ejector forward to

disengage the latch and simultaneously pull the NI-XNET

Transceiver Cable, as shown in the following figure.

NI 9860 Getting Started Guide | © National Instruments | 9

Figure 3. Inserting and Removing the NI-XNET Transceiver Cable

Push Lock

Ejector Forward

Pull Transceiver

Cable

Inserting and Removing the Power Cable

The NI 9860 connects to the provided power cable with an active

latching connector. To connect the power cable, push the end of

the power cable into the two-position connector until the internal

latch snaps into position. The latch emits an audible click when

engaged.

10 | ni.com | NI 9860 Getting Started Guide

Tabla de contenidos

Otros manuales de Equipo de grabación de National Instruments

National Instruments

National Instruments VXI-SB2020 Manual de usuario

National Instruments

National Instruments NI VISION PCI-8254R Manual de usuario

National Instruments

National Instruments GPIB-MAC Manual de usuario

National Instruments

National Instruments PXIe-416 Series Manual de usuario

National Instruments

National Instruments NI PCIe-8255R Manual de usuario

National Instruments

National Instruments NI VISION PCI-8254R Manual de usuario

National Instruments

National Instruments PXI-PCI 8330 Series Manual de usuario

National Instruments

National Instruments PCI-GPIB Manual de usuario

National Instruments

National Instruments NI-845 Series Manual de usuario

National Instruments

National Instruments GPIB-USB Series Instrucciones de instalación

National Instruments

National Instruments USB-8506 Manual de usuario

National Instruments

National Instruments VXI-1394 Manual de usuario

National Instruments

National Instruments NI-CAN Manual de usuario

National Instruments

National Instruments AT-DIO-32F Manual de usuario

National Instruments

National Instruments GPIB-COM Manual de usuario

National Instruments

National Instruments MXI-Express x1 Series Manual de usuario

National Instruments

National Instruments MXI PCIe-8371 Manual de usuario

National Instruments

National Instruments GPIB-SCSI-A Manual de usuario

National Instruments

National Instruments NI 9866 Manual de usuario

National Instruments

National Instruments MXI Manual de usuario

National Instruments

National Instruments PXI-8461/2 Manual de usuario

National Instruments

National Instruments NI VISION PCI-8254R Manual de usuario

National Instruments

National Instruments PC/104-GPIB Manual de usuario

National Instruments

National Instruments 8234 Manual de usuario

Manuales populares de Equipo de grabación de otras marcas

KV2 Audio

KV2 Audio 500 Series Manual de usuario

Robotics Technologies

Robotics Technologies microBus-Cam II Manual de usuario

Seca

Seca 460 Manual de usuario

Cognex

Cognex MVS-8000 Series Manual de usuario

Mect

Mect MPNC006 Series Manual de usuario

Bad Caf

Bad Caf THE LEASH Manual de usuario

Strymon

Strymon NIGHTSKY Manual de usuario

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manual de usuario

Tews Technologies

Tews Technologies TPMC465 Manual de usuario

Honeywell

Honeywell Excel 50 Manual de usuario

SeaLevel

SeaLevel COMM+8.LPCI Manual de usuario

Arturia

Arturia AUDIOFUSE STUDIO Manual de usuario

Rukra

Rukra RK-1240 Manual de usuario

Samson

Samson SCOM Manual de usuario

Dynacord

Dynacord DPS260 Manual de usuario

Nice

Nice Core Manual de usuario

Pyle Pro

Pyle Pro PSS8 Manual de usuario

RF-System

RF-System TinyGate Manual de uso y cuidado