National Instruments PXIe-5655 Manual del propietario
PXIe-5655 Safety,
Environmental, and
Regulatory Information
PXIe, 7.2 GHz PXI RF
Analog Signal Generator
Safety, Environmental, and
Regulatory Information
Read this document before you install, configure, operate, or
maintain this product. Users are required to familiarize
themselves with installation and wiring instructions in
addition to requirements of all applicable codes, laws, and
standards. Visit ni.com/manuals for more information about
your product, including specifications, pinouts, and
instructions for connecting, installing, and configuring your
system.
Icons
Notice —Take precautions to avoid data loss, loss of
signal integrity, degradation of performance, or damage to
the product.
Caution — Take precautions to avoid injury. Consult the
product documentation for cautionary statements when you
see this icon printed on the product. Cautionary statements
are localized into French for compliance with Canadian
requirements.
PXIe-5655 Safety, Environmental, and Regulatory Information
2 ni.com
Caution: Possibility of Electric Shock —Take
precautions to avoid electrical shock.
ESD Sensitive —Take precautions to avoid damaging the
product with electrostatic discharge.
Safety Guidelines
CAUTION
Observe all instructions and cautions in the user
documentation. Using the product in a manner
not specified can damage the product and
compromise the built-in safety protection.
ATTENTION
Suivez toutes les instructions et respectez toutes
les mises en garde de la documentation
d'utilisation. L'utilisation du produit de toute
autre façon que celle spécifiée risque de
l'endommager et de compromettre la protection
de sécurité intégrée.
Safety Voltages
Connect only voltages that are below these limits.
Absolute maximum input power (LO 0/1 IN) +17 dBm
PXIe-5655 Safety, Environmental, and Regulatory Information
© National Instruments Corporation 3
Absolute maximum reverse power
(LO 0/1 OUT) +18 dBm
Maximum input voltage (REF IN) 3.3 V pk-pk
Measurement Category CAT I/O
PXIe-5655 Safety, Environmental, and Regulatory Information
4 ni.com
Measurement Category
WARNING
Do not connect the product to signals or use for
measurements within Measurement Categories II,
III, or IV, or for measurements on MAINs circuits or
on circuits derived from Overvoltage Category II,
III, or IV which may have transient overvoltages
above what the product can withstand. The
product must not be connected to circuits that
have a maximum voltage above the continuous
working voltage, relative to earth or to other
channels, or this could damage and defeat the
insulation. The product can only withstand
transients up to the transient overvoltage rating
without breakdown or damage to the insulation.
An analysis of the working voltages, loop
impedances, temporary overvoltages, and
transient overvoltages in the system must be
conducted prior to making measurements.
MISE EN GARDE
Ne pas connecter le produit à des signaux dans
les catégories de mesure II, III ou IV et ne pas
l'utiliser pour des mesures dans ces catégories, ou
des mesures sur secteur ou sur des circuits
dérivés de surtensions de catégorie II, III ou IV
pouvant présenter des surtensions transitoires
supérieures à ce que le produit peut supporter. Le
produit ne doit pas être raccordé à des circuits
ayant une tension maximale supérieure à la
tension de fonctionnement continu, par rapport à
la terre ou à d'autres voies, sous peine
d'endommager et de compromettre l'isolation. Le
produit peut tomber en panne et son isolation
risque d'être endommagée si les tensions
PXIe-5655 Safety, Environmental, and Regulatory Information
© National Instruments Corporation 5
transitoires dépassent la surtension transitoire
nominale. Une analyse des tensions de
fonctionnement, des impédances de boucle, des
surtensions temporaires et des surtensions
transitoires dans le système doit être eectuée
avant de procéder à des mesures.
Measurement Category I is for measurements performed on
circuits not directly connected to the electrical distribution
system referred to as MAINS voltage. MAINS is a hazardous live
electrical supply system that powers equipment. This
category is for measurements of voltages from specially
protected secondary circuits. Such voltage measurements
include signal levels, special equipment, limited-energy parts
of equipment, circuits powered by regulated low-voltage
sources, and electronics.
NOTE
Measurement Categories CAT I and CAT O are
equivalent. These test and measurement circuits
are for other circuits not intended for direct
connection to the MAINS building installations of
Measurement Categories CAT II, CAT III, or CAT IV.
Safety Compliance Standards
This product is designed to meet the requirements of the
following electrical equipment safety standards for
measurement, control, and laboratory use:
•IEC 61010-1, EN 61010-1
•UL 61010-1, CSA C22.2 No. 61010-1
NOTE
For safety certifications, refer to the product label
or the Product Certifications and Declarations
section.
PXIe-5655 Safety, Environmental, and Regulatory Information
6 ni.com
EMC Guidelines
This product was tested and complies with the regulatory
requirements and limits for electromagnetic compatibility
(EMC) as stated in the product specifications. These
requirements and limits are designed to provide reasonable
protection against harmful interference when the product is
operated in its intended operational electromagnetic
environment.
This product is intended for use in commercial and light-
industrial locations. However, harmful interference may occur
in some installations, when the product is connected to a
peripheral device or test object, or if the product is used in
residential areas. To minimize interference with radio and
television reception and prevent unacceptable performance
degradation, install and use this product in strict accordance
with the instructions in the product documentation.
Furthermore, any changes or modifications to the product not
expressly approved by NI could void your authority to operate
it under your local regulatory rules.
PXIe-5655 Safety, Environmental, and Regulatory Information
© National Instruments Corporation 7
EMC Notices
Refer to the following notices for cables, accessories, and
prevention measures necessary to ensure the specified EMC
performance.
NOTICE
For EMC declarations and certifications, and
additional information, refer to the Product
Certifications and Declarations section.
NOTICE
Changes or modifications to the product not
expressly approved by NI could void your
authority to operate the product under your local
regulatory rules.
NOTICE
The performance of this product can be disrupted
if subjected to Electrostatic Discharge (ESD)
during operation. To prevent damage, industry-
standard ESD prevention measures must be
employed during installation, maintenance, and
operation.
PXIe-5655 Safety, Environmental, and Regulatory Information
8 ni.com
NOTICE
This product may become more sensitive to
electromagnetic disturbances in the operational
environment when test leads are attached or
when the product is connected to a test object.
NOTICE
Operate this product only with shielded cables
and accessories. Do not use unshielded cables or
accessories unless they are installed in a shielded
enclosure with properly designed and shielded
input/output ports and connected to the product
using a shielded cable. If unshielded cables or
accessories are not properly installed and
shielded, the EMC specifications for the product
are no longer guaranteed.
NOTICE
The length of all I/O cables must be no longer
than 3 m (10 ).
NOTICE
You must install PXI EMC Filler Panels, NI part
number 778700-01, in all open chassis slots.
Electromagnetic Compatibility Standards
This product meets the requirements of the following EMC
standards for electrical equipment for measurement, control,
and laboratory use:
PXIe-5655 Safety, Environmental, and Regulatory Information
© National Instruments Corporation 9
•EN 61326-1 (IEC 61326-1): Class A emissions; Basic
immunity
•EN 55011 (CISPR 11): Group 1, Class A emissions
•AS/NZS CISPR 11: Group 1, Class A emissions
NOTE
Group 1 equipment (per CISPR 11) is any
industrial, scientific, or medical equipment that
does not intentionally generate radio frequency
energy for the treatment of material or
inspection/analysis purposes.
NOTE
In Europe, Canada, Australia and New Zealand
(per CISPR 11) Class A equipment is intended for
use only in non-residential locations.
Environmental Guidelines
NOTICE
This model is intended for use in indoor
applications only.
PXIe-5655 Safety, Environmental, and Regulatory Information
10 ni.com
Tabla de contenidos
Otros manuales de Generador portátil de National Instruments
National Instruments
National Instruments NI PXIe-5450 Manual de usuario
National Instruments
National Instruments NI 5401 Manual de usuario
National Instruments
National Instruments PXIe-5650 Manual de usuario
National Instruments
National Instruments NI PXIe-5673E Manual
National Instruments
National Instruments PXIe-5413 Manual de usuario
National Instruments
National Instruments NI 5741 Manual de usuario
National Instruments
National Instruments PXIe-5673 Manual
National Instruments
National Instruments NI-5742 Manual de usuario
National Instruments
National Instruments NI 5422 Manual de usuario
National Instruments
National Instruments NI 5402 Manual de usuario
National Instruments
National Instruments PXIe-5654 Manual
National Instruments
National Instruments NI 5402 Manual
National Instruments
National Instruments PXIe-5654 Manual
National Instruments
National Instruments NI 5650 Manual de usuario
National Instruments
National Instruments NI PCI-6542 Manual de usuario
National Instruments
National Instruments NI PXIe-5450 Manual del propietario
National Instruments
National Instruments FD-11601 Manual de usuario
National Instruments
National Instruments DAQArb 5411 Manual de usuario
National Instruments
National Instruments NI 5401 Manual de usuario
National Instruments
National Instruments PXIe-5745 Manual de usuario
