NARGESA C2006 Manual de usuario
INSTRUCTIONS BOOK
PRADA NARGESA, S.L
Ctra. de Garrigàs a Sant Miquel s/n
17476 PALAU DE STA. EULALIA (GIRONA) SPAIN
Tel. 972 568085 - Fax 972 568320
HYDRAULIC SHEAR
C2006
Thank you for choosing our machines
www.nargesa.com
C2006 HYDRAULIC SHEAR INSTRUCTIONS BOOK 2
INDEX
1. CHARACTERISTICS OF THE MACHINE ...............................................................................
1.1. Identification of the machine .......................................................................................
1.2. General dimensions ....................................................................................................
1.3. Description of the machine ..........................................................................................
1.4. Identification of the machine .......................................................................................
1.5. General features ........................................................................................................
1.6. Description of safety devices ......................................................................................
2. TRANSPORTATION AND STORAGE ....................................................................................
2.1. Transportation .............................................................................................................
2.2. Storage conditions ……………….................................................................................
3. MANINTENANCE ....................................................................................................................
3.1. General Maintenance ..................................................................................................
4. INSTALLMENT AND START UP ............................................................................................
4.1. Location of the machine ..............................................................................................
4.2. Dimensions and working site …...................................................................................
4.3. Admissible outer conditions ........................................................................................
4.4. Connection to power supply ………….........................................................................
5. HANDLING BOOK ...................................................................................................................
5.1. Introduction .................................................................................................................
5.2. Control panel ...............................................................................................................
5.3. Feeding of the guillotine ..............................................................................................
5.4. Activation of the machine ............................................................................................
5.5. Surfing through the top memories ...............................................................................
5.6. Positioning the top .......................................................................................................
5.6.1. Introducing the desired figure ........................................................................
5.6.2. Cancelling the introduction of a figure ............................................................
5.6.3. Considerations to bear in mind ......................................................................
5.7. Operation mode ..........................................................................................................
5.7.1. Manual mode .................................................................................................
5.7.2. Automatic mode .............................................................................................
5.8. Deletion of the cutting meter .......................................................................................
5.9. Correct the top ............................................................................................................
5.10. Menus of the block ....................................................................................................
5.10.1. Menu to edit blocks ......................................................................................
5.10.2. Selection of the block ...................................................................................
5.10.3. Definition of the performance mode .............................................................
5.10.4. Adding cells ..................................................................................................
5.10.5. Eliminating cells ...........................................................................................
5.10.6. Edition of cells ..............................................................................................
5.10.7. Deletion of the cutting meter ........................................................................
4
4
4
4
5
6
7
8
8
8
9
9
10
10
10
10
11
12
12
12
13
13
14
15
15
17
18
18
19
20
21
22
23
24
24
25
26
27
27
29
C2006 HYDRAULIC SHEAR INSTRUCTIONS BOOK 3
5.11. Menu to operate blocks .............................................................................................
5.11.1. Block selection .............................................................................................
5.11.2. Operating with one block .............................................................................
6. ADJUSTMENT OF THE BLADES ...........................................................................................
7. STANDBY OF THE MACHINE ................................................................................................
8. UNUSUAL PERFORMANCE SITUATIONS ............................................................................
9. WARNINGS .............................................................................................................................
10. ACCESORIES ........................................................................................................................
TECHNICAL ANNEXES
30
30
31
32
33
34
35
C2006 HYDRAULIC SHEAR INSTRUCTIONS BOOK 4
1. CHARACTERISTICS OF THE MACHINE
1.1. Identification of the machine
1.2. General dimensions
Picture 1. External dimensions of the machine
1.3. Descripción de la máquina
The guillotine C2006, has been designed specifically for cutting metal sheets.
The manufacturer will not take any responsibility for the damages caused to the machines or the operatives
using it at any other operation different from the ones previously specified.
The C2006 is according to the European regulations and normative for the manufacturing of machinery.
PRADA NARGESA S. L is not liable for any damage that might occur due to misuse or failure by
users to comply with the safety standards.
Trademark Nargesa
Type Hydraulic shear
Model C2006
C2006 HYDRAULIC SHEAR INSTRUCTIONS BOOK 5
1.4. Identification of the machine
Commands control
Rammers
Electric box
Front protection
Screws to level
the machien
Lifting spot
Photocell
Side protections
Stands for the
entrance of the
metal sheet
Power motor
C2006 HYDRAULIC SHEAR INSTRUCTIONS BOOK 6
Picture 2. Nameplate
1.5. General features
Engine power 5,5 KW / 7,5 CV
Three-phased tension 230/400 V
Cutting Capacity: mild steel 6 mm
Cutting capacity: stailess steel 4 mm
Nº of hammers 10 unidades
Cutting length 2030 mm
Neck 190 mm
Gauge displacement 700 mm
Strokes per minute 10 strokes
Position accuracy and repeatibility +/- 0,1 mm
Dimensions 2671x2364x1762 mm
Weight 4850 Kg
C2006 HYDRAULIC SHEAR INSTRUCTIONS BOOK 7
Protection covers must not be removed to do the maintenance works. This job must be carried out by
highly qualified technicians. PRADA NARGESA will not accept any responsibility for the damages cau-
sed by not bearing in mind to what has been previously exposed on this book.
1.6. Description of safety devices
The fixed safety devices the guillotine C2006 has are lateral to avoid any handling, the front protection
avoids from acceding to the rammers side, Protections in the back side of the machine covering the belts
and pulley of the back top, the outet ramp for the material and the upper protection cover of the piston mo-
veable part.
Picture 3. Safety devices
ResBack protection
of the top belts.
Upper safety device for the hydraulic
piston protection.
Outlet rampfor
the cut material.
Front protection to save access
to the cutting blade.
Protection side neck.
C2006 HYDRAULIC SHEAR INSTRUCTIONS BOOK 8
2. TRANSPORTATION AND STORAGE
2.1. Transportation
The lifting of the machine will be carried out by a crane, using the clamping points indicated for that. The
machine will be never lifted by any other side but the indicated one.
Picture 4. Transportation of the machine
2.2. Storage conditions
The machine will not be stored in a place that hasn’t got the following requirements:
* Humidity between 30% and 95% without water condensation.
* Temperature from -25 to 55ºC or 75ºC for a length of time not exceeding 24h (these must be considered
storage conditions)
* It is advisable not to pile up machines or heavy objects on top of it
C2006 HYDRAULIC SHEAR INSTRUCTIONS BOOK 9
WARNING: Stop the machine to make the maintenance.
3. MAINTENACNE
3.1. General maintenance
- The oil container level must be checked every 1000 hours of work.
The peephole to the oil level is located in the upper part of the container. In case there is a lack of oil, just
fill it up to the peephole mark.
- Replace the hydraulic oil container every 4000 hours of work.
- Oil: CEPSA HYDRAULIC HM 68
Once the oil has been changed, it is necessary to start up the machine and activate the pedal in
intermittence by increasing the pressure time gradually until the circuit is full.
- Grease up the bolts periodically according to the level of use.
- If it is a steady and daily use, they must be greased avery month.
- Lubricate the top spindles weekly with grease or oil.
- Lubricate all guides greasers every month.
Drain plug
Oil dipstick
Fill plug
Otros manuales para C2006
1
Tabla de contenidos
Otros manuales de Herramientas eléctricas de NARGESA
NARGESA
NARGESA MP3003 CNC Manual de usuario
NARGESA
NARGESA MX340G Manual de usuario
NARGESA
NARGESA C2006 Manual de usuario
NARGESA
NARGESA C3006 Manual de usuario
NARGESA
NARGESA MP1400 CNC Manual de usuario
NARGESA
NARGESA MC400 Manual de usuario
NARGESA
NARGESA MP3003 CNC Manual de usuario
NARGESA
NARGESA MX340G Manual de usuario
NARGESA
NARGESA C3006 Manual de usuario
