Murphy Selectronic MT90 Manual de usuario

MT-9004B page 1 of 2

MT90 Model

■

±1 RPM Accuracy

■

Easy Calibration

■

Clear-Read LCD Display

■

Back Light for Night Viewing

(Battery Powered models)

■

Input Source Can Be a Magnetic Pickup

or Engine Alternator

■

Power Supplied by Magnetic Pickup

or 12, 24, or 32 VDC Battery System

Description

The Murphy SELECTRONIC®MT90 is a digital

tachometer. Its high accuracy and dependability

result from use of a quartz crystal time based and

digital, solid-state electronics.

Tachometer power is supplied by either a Murphy

magnetic pickup, mounted at the flywheel ring-

gear of an engine, or by a 12, 24 or 32 volt DC

battery system.

RPM data is supplied by either a Murphy magnet-

ic pickup or by the alternator in your battery

charging circuit. The MT90 also has back-lighting

for easy readings in low lit areas; this lighting

requires a battery power source.

RPM Calibration

The MT90 is calibrated to engine RPM by setting a

series of calibration rotary switches on the back of

the tachometer. The proper switch sequence for the

engine is determined by (1) the number of ring gear

teeth for the magnetic pickup, or (2) by the ratio of

alternator to engine pulley diameter, and the num-

ber of poles of the alternator.

Applications

Typical applications include: Generators,

Compressors, Industrial Engines, Oil Field

Equipment, Marine Vessels, Vehicles, Farm

Equipment, and Construction Equipment.

Specifications

Signal Input Voltage: 4 to 35 Vrms from a mag-

netic pickup or alternator

Pulses per Revolution: 3 to 999.

Power Requirements:

• Pickup Power: 4-35Vrms

• Battery Power: 8-40 VDC (12, 24, 32 volt).

Current:

• Tach back-light Off, 4mA @ 40 VDC.

• Tach back-light On, 25 mA @ 40 VDC.

Case: 1018 polycarbonate/polyester blend.

Lens: Polycarbonate.

Bezel: #430 Stainless Steel.

Display: LCD, 4-digit, seven segment.

Operating Temperature: -4 to 158°F

(-20 to 70°C).

Storage Temperature: -13 to 185°F (-25 to 85°C).

Mounting Hole: 3-7/16 in. (87 mm).

Shipping Weight: 14 oz. (0.4 kg).

Shipping Dimensions: 5-1/2 x 5-1/2 x 5-1/2 in.

(140 x 140 x 140 mm)

Warranty

A limited warranty on materials and workmanship is

given with this FW Murphy product. A copy of the

warranty may be viewed or printed by going to

www.fwmurphy.com/support/warranty.htm

Products covered by this bulletin comply with

EMC Council directive 89/336/EEC regarding

electro-magnetic compatibility except as noted.

See “Special Note” for Magnetic Pickup

Powered MT90 applications (back page).

Calibration

Rotary Switches

(located under

removable

rubber seal)

Mounting

Clamp

3-5/8 in

(92 mm)

3-1/8 in

(80 mm)

Terminal

Screws

X 1000 X 100 X 10

Dimensions

Side View

Back View

MT-9004B

Revised 03-06

Catalog Section 20

(00-02-0068)

Digital Tachometer by Murphy

SELECTRONIC®

MT-9004B page 2 of 2

100's 10's 1's

X 1000 X 100 X 10

2345

Magnetic

Pickup

Locknut

Hole Drilled and

Tapped, Bolt Thread

NOTE: Gap from face of gear tooth must be enough for gear to move. Rotate gear completely

to be sure of minimum, no-touch clearance. See instructions supplied with the magnetic sensors.

To get minimum of 4 VAC RMS, gap tolerance is critical. Turn the pickup in until it stops against

the face of a gear tooth. Back the pickup out only enough to allow rotation of the gear. Rotate the

gear, if any tooth touches the pickup, back it out to clear the tooth. After clear rotation secure the

pickup locking nut.

MT90

with

customer

wiring

When calibrating for use with a magnetic

pickup, dial in the number of flywheel teeth

or pulses per revolution: for example, if the

flywheel has 125 teeth then dial in125.

See Calibration for alternator installation.

Magnetic Pickup Powered MT90

(No back-lighting)

Magnetic Pickup

Locknut

Hole Drilled and

Tapped, Bolt Thread

NOTE: Gap from face of gear tooth must be enough for gear to move. Rotate gear completely

to be sure of minimum, no-touch clearance. See instructions supplied with magnetic sensor.

100's 10's 1's

X 1000 X 100 X 10

Battery

12V-24V-32V

Alternator

When calibrating for use with a magnetic

pickup, dial in the number of flywheel teeth

or pulses per revolution: for example, if the

flywheel has 125 teeth then dial in125.

See Installation and Calibration for alternator

installation.

2345

Back-light

ON/OFF

MT90

with

customer

wiring

Tachometer

Terminal NOTE:

Alternator

must be

equipped

with a Tach.

terminal

(auxiliary

AC terminal).

Battery Powered MT90

(With back-lighting)

MP3298

Terminal 2: connects to battery (-) or ground.

Terminal 3: connects the back-light to battery (+), (back-light can only be used

when powering from battery).

Terminal 4: connects to battery (+) or power from magnetic pickup or alterna-

tor.

Terminal 5: RPM input signal from magnetic pickup.

Terminal 6: RPM input signal from alternator.

Typical Wiring Diagrams for MT90

Magnetic Pickups

Calibration

To calibrate the MT90 for your engine, remove the rubber seal on the

back of the tachometer and dial in the correct number.

• Magnetic Pickup: dial in the number of teeth on your ring gear.

Set the switches from left to right. For example, if the engine gear

has 125 teeth, dial a 1on the left switch, a 2on the center switch,

and a 5on the right switch. Using this setting, the MT90 will

count the passing teeth and convert them into engine RPM.

• Alternator: Multiply the ratio of alternator to engine pulley dia-

meter, times, the number of poles of the alternator divided by two,

to determine the correct calibration number (also see “Other

Calibration Methods”).

Other Calibration Methods (teeth or ratio unknown)

For setting the calibration switches when the number of pulses per

revolution are not known, set the rotary switches on back of the MT90

to 0-6-0 and read the tachometer at a known engine RPM. This can be

read by a hand-held tachometer or any means which tells actual RPM

The reading is the input frequency in hertz. Multiply the frequency

times 60 and divide the result by the engine RPM. Set this number into

the rotary calibration switches. NOTE: If pulses per revolution are not

a whole number, for example: 21.5, a setting of 021 will read slightly

high and a setting of 022 will read slightly low.

To order a MT90 for your application, use the diagram below.

MT90 – ___ – ___

How to Order

Bezel

Blank = Bright stainless

B = Black stainless

Face Plate

1 = White background

To order a magnetic pickup, specify model number.

Example: MP3298

Pickup Models Total Length Threaded Length Thread Size

MP3298*3 in. (76 mm) 3 in. (76 mm) 5/8-18 UNF

MP7906†3 in. (76 mm) 3 in. (76 mm) 3/4-16 UNF

MP7905†† 4-1/2 in. (114 mm) 4-1/2 in. (114 mm) 3/4-16 UNF

*Replaces 20-01-0080 and MP100. Lead wire hookup (12 in. [305 mm]).

†Replaces 20-01-0081. Lead wire hookup (12 in. [305 mm]).

†† Replaces 20-01-0082. Lead wire hookup (12 in. [305 mm]).

In order to consistently bring you the highest quality, full featured products, we reserve the right to change our specifications and designs at any time.

Printed in U.S.A. 0290998

In order to consistently bring you the highest quality, full featured products, we reserve the right to change our

specifications and designs at any time. MURPHY, the Murphy logo, and Selectronic

are registered and/or com-

mon law trademarks of Murphy Industries, Inc. This document, including textual matter and illustrations, is copy-

www.fwmurphy.com

918.317.4100 Email: [email protected]

Tabla de contenidos

Otros manuales de Pieza de automóvil de Murphy

Murphy

Murphy Exhaust Pyrometers 10705146 Manual de usuario

Murphy

Murphy Diagnostic Display PV10 Manual de usuario

Murphy

Murphy Pull/Push DC Solenoids RP2307B Manual de usuario

Murphy

Murphy Digital Time Meters HD35-CD Manual de usuario

Murphy

Murphy Dump Valves DV Series Manual de usuario

Murphy

Murphy Engine Panels WD300-LV Manual de usuario

Murphy

Murphy Diesel-Fuel Shutoff Valve SV-Series Manual de usuario

Murphy

Murphy TAH-97026B Manual de usuario

Murphy

Murphy Lube Level Maintainer LM2000 Manual de usuario

Murphy

Murphy Selectronic DT9800 Manual de usuario

Murphy

Murphy SELECTRONIC TACHSWICH DT9803 Manual de usuario

Murphy

Murphy MURPHYMATIC AT03069 Manual de usuario

Murphy

Murphy M5081 Series Manual de usuario

Murphy

Murphy CNG-92200H Manual de usuario

Murphy

Murphy Digital Tach/Hourmeter with Overspeed Trip Point... Manual de usuario

Murphy

Murphy MLA20 Manual de usuario

Murphy

Murphy Gear Oil Pressure Sender EGPK-95083N Manual de usuario

Murphy

Murphy Rack Puller RP75 Manual de usuario

Murphy

Murphy EG-05012B Manual de usuario

Murphy

Murphy Diesel Fuel Check Valves CKV1WPS Manual de usuario

Manuales populares de Pieza de automóvil de otras marcas

Dakota Digital

Dakota Digital 650277 Manual de usuario

bosal

bosal 037031 Manual de usuario

Edelbrock

Edelbrock 66332 Manual de usuario

Edelbrock

Edelbrock Honda XR400 Manual del propietario

Vintage Air

Vintage Air 571063 Manual de usuario

Edelbrock

Edelbrock 70005 Manual de usuario

GFB

GFB EX38 Manual de usuario

Edelbrock

Edelbrock 65272 Manual de usuario

bosal

bosal 028091 Manual de usuario

Dodge

Dodge 8W-43 Guía de inicio rápido

ICI

ICI Magnum FBM10DGN Manual de usuario

Volant Perfomance

Volant Perfomance 19435 Manual de usuario

BENDIX

BENDIX GEN 4 GEN 5 ABS Manual de usuario

Edelbrock

Edelbrock 72552 Manual de usuario

Edelbrock

Edelbrock 70024 Manual de usuario

Edelbrock

Edelbrock 6719 Manual de usuario

Edelbrock

Edelbrock 5486 Manual de usuario

Vintage Air

Vintage Air 571065 Manual de usuario