Murideo Fresco SIX-G Manual de usuario
Page 1 of 45
Call the AVPro Team at –North America 877-886-5112 International +1-605-27 -6055
Murideo
Fresco SIX-G
HDMI 2.0 Test Pattern Generator
HDCP 2.2 Tester
User s Manual
Version 1.00
Page 2 of 45
Call the AVPro Team at –North America 877-886-5112 International +1-605-27 -6055
Important Safety Information
• Follow all instructions
• Use only a dry cloth to clean
• Use caution not to block side vents on unit
• Indoor use only: To reduce the risk of electric shock, do not use near water or expose to
rain or moisture. Keep away from excess moisture
• Do not use near heat sources such as room heaters, hot A/V equipment
• Read all warnings
• Use only accessories provided by Murideo
• Unplug the device during lightning storms or when unused for long periods of time
• Keep away from open flames
• Protect all connected cords including power cords from being pinched, compressed, and
stepped on
• Do not open the case. All servicing should be done only by qualified and approved service
personnel and will void the warranty.
• Electrical Input Rating: Power over 5V/DC 700mA. Caution: Use only the supplied AC/DC
Adapter
• Operating temperature range: e.g. 0 to 0C.
• For charging use the provided 5V/ DC 3A supply only
• To disconnect power sources, remove the AC/DC adapters from the wall outlets.
Attention:
1. In order to protect your SIX-G and complete system under test from possible damages,
please don't turn on the SIX-G power switch before generator Output is attached to
tested device (repeater, video processor or display) input.
Please make sure that system under test is completely powered off before you insert or
extract HDMI cable to any of involved devices.
2. Please insert and extract HDMI cables from your SIX-G gently and with high level of care.
3. During Hot-Plug between HDMI connector and receptacle (when tested device is On) ESD
discharge can occur due to the potential differences (possible ground -loop) between
powered equipments. These potential differences can be on extremely high level.
Our Fresco SIX-G HDMI output is protected against ESD discharge till 7KV on all active
HDMI lines, but in case if massive discharge will be over that value, will cause serious
damage to SIX-G internal circuitry and can make SIX-G HDMI output completely
inoperable. We have sophisticated methods to measure directly on High voltage
protection chips evidences of such unwanted ESD event, but unfortunately, that will
automatically void SIX-G warranty. In your own interest please pay full attention and
prevent your workplace from occurrence of ESD by trying to create Static-safe working
environment.
Page 3 of 45
Call the AVPro Team at –North America 877-886-5112 International +1-605-27 -6055
Table of Contents
Page Overview
Page -5 Key Features
Page 5 What's in the Box
Page 6 Functionality Diagram
Page 7-9 Connecting Muridio SIX-G
•Manual Operation
•Operation with Spectracal CalMAN 5
•Operation with included PC Software
Page 10 Manual Operation& System Testing
Page 11 Six-G Input & Output Connections
Page 11-13 Buttons & Indicator Functions
Page 13-16 Navigation Basics
Page 16-23 PC Software
•Connection
•Format Selection
•Timing Calculator
•Pattern Selection
•Settings
•EDID Management
•RGB Triplets
Page 2 -30 Test Pattern Usage
•White PLUGE
•Black PLUGE
•Color & Tint
•ISF Color Girls
•Sharpness & Geometry
•Color Temp
•Chroma Multiburst
Page 31-37 Troubleshooting with the SIX-G
Page 38 Specifications
Page 39 List of Supported Resolutions
Page 0 API
Page 0- 1 FCC Compliance
Page 2- 5 Warranty
Page 4 of 45
Call the AVPro Team at –North America 877-886-5112 International +1-605-27 -6055
Overview
Thanks for purchasing the Murideo SIX-G – an ISF Pro Tool!
The Murideo SIX-G is intended for the AV integration market to confirm HDMI 2.0(a) and HDCP
2.2 operation at the 18 GBPS level. Additionally, the SIX-G is an excellent troubleshooting tool for
distributed HDMI systems and a reference source for video calibration. SIX-G beside many other
sophisticated features is also compatible and certified by SpectraCals, CalMAN.
One of the biggest challenges for integrators today is determining what infrastructure to put in
the systems they design and further verifying, that all of the components will work together. Over
the past few years UHD TVs have been a mix of HDCP 2.2 and 1. , 300MHz and 600Mcsc – even
to the point of varying by port.
The SIX-G takes the guess work out of troubleshooting, and provides absolute information about
HDMI components that will work and IDs ones that won’t work – all in a hand-held, ruggedized,
portable field tool.
The SIX-G is designed to be extremely accessible, shipping with free control software, plus front
panel controls that allow access to 99% of the features.
The SIX-G is the only unit to carry the complete suite of ISF test patterns, select-able color output
level, RGB Triplets and Constant APL (Average Picture Level) all in one place, making it a
calibrators dream.
Note: The SIX-G ships with a protective cover on the screen that you may remove, although this is
not required for operation.
Key Features:
•HDMI 2.0(a) Support. 600 Mcsc - 2160P @60 : : Maximum Resolution
•HDR (High Dynamic Range) Support
•HDCP Pass/Fail - HDCP 2.2, 1. or None Indicator Light >Some of the K UHDs on the
market today support HDCP 2.2 - The SIX-G will tell you what the TV will and won’t
support.
•Hot Plug Detect Indicator Light > On the fly indicator for troubleshooting issues especially
when switching, splitting and extending HDMI
•CalMAN Supported > Advanced features available to CalMAN like APL, ISF Test Patterns
and more. No driver required & Simple setup.
•EDID Read and Save functionality >did you know most K TVs still have 2K preferred
timings? Know what your TV is telling you.
Page 5 of 45
Call the AVPro Team at –North America 877-886-5112 International +1-605-27 -6055
•8 Bit per pixel color depth > Todays TVs are still 2 bits per pixel, but the new Blu-Ray
may be 30, so lots of headroom is available.
•USB Control and WebOS Support
•Portable - Battery Operated > Rechargeable batteries included make field troubleshooting
much easier.
•Optimized Ergonomics – 3” LCD display and simple menu system makes SIX-G very user
friendly.
•ISF Certified and includes ISF Test Patterns >Specialty Black, White, Multi-burst, and more.
People patterns for checking flesh tones and color decoding after calibration.
•Plenty of specialty patterns > Everything you need to setup, calibrate, and troubleshoot
HDMI/DVI video systems
•Includes audio confidence test tones > to make sure audio is active on the HDMI line
What s in the Box
• SIX-G Generator
• 5 V DC/AC Power Supply / Charger (110-2 0 VAC) with set of International plugs (US, UK,
AU, EU).
• Rechargeable Battery Pack (installed)
• Hard Case
• 3’ Micro USB to USB cable
• 1’ 3.5mm to DB9 (F) serial cable adapter
Please read the entire manual before turning on your new Murideo Six-G for helpful tips on
charging and battery life extension.
Page 6 of 45
Call the AVPro Team at –North America 877-886-5112 International +1-605-27 -6055
Front Panel Functional Description
Rear Connector Panel
Page 7 of 45
Call the AVPro Team at –North America 877-886-5112 International +1-605-27 -6055
Connecting the MURIDEO SIX-G
The SIX-G generator can be operated manually, PC interfaced with Spectracal’s CalMan version
5.6 or greater (in automated mode), or the supplied application software.
Manual Operation Connection
1. Connect the AC power adapter to the generator and plug it into AC power or power the
generator using the internal battery.
2. Connect the HDMI cable between the generator and the unit under test.
3. You are now ready to power up the generator and unit under test and proceed with your
performance verification.
a. The display will show the last pattern and resolution used. The HPD light will be
ON and the HDCP light will be ON if HDCP is enabled.
. To change the output resolution - Push the OK button to recall the TIMING RES menu or
push the YELLOW hot key to bring up a list of commonly used timings. Use the UP/DOWN
keys to step to the timing you want and then push the OK button.
Page 8 of 45
Call the AVPro Team at –North America 877-886-5112 International +1-605-27 -6055
5. To change the test pattern use the UP/DOWN keys to step to the desired test pattern. The
test pattern is shown on the front panel display.
6. The Purple hot key will take you to the HDCP Setting menu. Use the UP/DOWN keys to
step to the desired HDCP mode and the OK key to make the selection
Spectracal s CalMan 5 Connections:
You will need a SIX-G, a PC with a licensed copy of CalMan installed, a light measurement meter,
and cables. (Contact AVPro if you need a current License or details when other calibration
software will be SIX–G supported.)
1. Connect the supplied AC power adapter to the SIX-G. Due to the time required it is
recommended to use the AC power adapter during the calibration procedure.
2. Connect the Control port of the SIX-G and the light meter to the PC USB ports.
3. Connect the SIX-G output to the monitor using an HDMI cable.
Page 9 of 45
Call the AVPro Team at –North America 877-886-5112 International +1-605-27 -6055
PC w/included Software Application Connections:
You will need a SIX-G, a PC with the application installed, supplied HDMI cable, supplied RS-232
cable, and supplied AC power adapter.
1. Connect the SIX-G to it AC power adapter.
2. Connect the SIX-G to the PC using the supplied USB cable or alternatively supplied RS-232
cable terminated with DB 9 female receptacle (in case if your host PC does have physical
Serial COM Port).
3. Connect the SIX-G output to the unit under test using an HDMI cable.
Manual Operation & System Testing
Manual operation is well suited for testing video distribution system components prior to installation or
for step-by-step diagnostics and to isolate faulty component within an installed system.
Typical manual operation steps:
1. Connect the SIX-G generator to the unit under test using an HDMI cable.
Page 10 of 45
Call the AVPro Team at –North America 877-886-5112 International +1-605-27 -6055
2. Power ON the SIX-G generator using the internal battery or the supplied AC power adapter.
3. Power ON the unit under test.
. Use the navigation keys of the SIX-G to select the resolution, pattern and HDMI setting desired for
testing.
5. The unit under test will display the selected test pattern if it is compatible with the test signal
timing and signal parameters.
6. If the test pattern is not displayed check the following: HDP front panel light is ON, check that the
HDCP SETTINGS mode is compatible with the unit under test, verify the input you are using is
compatible with the test signal format – Note that NOT all HDMI inputs on monitors are the same,
verify the sink EDID by going to the SINK EDID INFO menu on the SIX-G.
If you are testing or servicing a system you can connect the SIX-G to any HDMI input connection along the
signal path. You can work step by step from the Sink back to the Source or from the Source to the Sink.
Creating test system with multiple SIX-G and allowing 3rd party system integration.
For purpose setting up large test system with multiple SIX-G, we provided Serial port via 3.5 mm, 3 pin
receptacle and in supplied Control software, mechanism for Serial identification for each connected SIX-G
device.
We also added in accessories proprietary serial cable, terminated on one side with DB9 (9 pin connector
and on the other side with 3.5mm (aka: Mini Stereo Jack) with 3 contacts.
Serial Connection diagram:
Otros manuales para Fresco SIX-G
1
Tabla de contenidos
Otros manuales de Equipo de prueba de Murideo
Manuales populares de Equipo de prueba de otras marcas
SMART
SMART KANAAD SBT XTREME 3G Series Manual de usuario
Agilent Technologies
Agilent Technologies BERT Serial Manual de usuario
Agilent Technologies
Agilent Technologies N3280A Manual de usuario
Vernier
Vernier Go Direct Voltage Manual de usuario
Lifeloc
Lifeloc R.A.D.A.R. Manual de usuario
Fluke
Fluke T5-600 Instrucciones de funcionamiento e instalación
