Murata MURATA BOY Manual
MURATA BOY Paper Craft
Assembly Direction
Download the paper craft data and print it out to assemble MURATA BOY.
Complete the paper craft using all of the parts printed.
It will make a nice family project.
* Make sure to print out all parts. Some printers may have different page settings.
All right reserved, Copyright Murata Manufacturing Co.,Ltd. 2006
Before Assembling
Necessary tools
Scissors
Paper cutter
Ruler
Tw e e ze r s
Glue
Something heavy to press down glued areas (a thick book or magazine)
*Attention!
Be careful not to cut yourself when using the scissors or paper cutter.
Make sure to use glue in a well-ventilated room.
When weighing down the glued area, make sure that the glue will not stick the parts and the
weight together.
*Attention!
Some small parts may be hard to fold.You can try folding before cutting, or tracing the line with a
blunt point before folding.
Folding and Cutting Instructions
Follow the instructions below for cutting and folding paper craft parts.
Solid line
Cut along this line using scissors.
Dotted line
Fold with this line out. (Mountain-shaped fold)
Dot and dash line
Fold with this line in. (Valley-shaped fold)
1
All right reserved, Copyright Murata Manufacturing Co.,Ltd. 2006
Before Assembling
Head
Fold lightly to form a
ball shape.
Face
Fold lightly to form a
ball shape.
Close the red facet last.
Neck
The neck part
should be
assembled like a
box.
Body
For the body part,
glue the chest and
stomach areas first,
assemble the hip area,
and glue the back
and neck facets
together to close.
Backpack
Assemble the side of
the large box.Then
assemble the side of
the small box. Close
the red area last.
Shoulders
Lightly fold side facets to
form a hexagon first.
Arms
Assemble the blue elbow
region first. Fold upper and
lower arms into tubes. Insert
the blue elbow part and glue
the red facet down.
Hands
Glue the sides to form
a back of the hand.
Back of the hand
should be rounded.
Glue the red palm last.
Last step
First step
2
All right reserved, Copyright Murata Manufacturing Co.,Ltd. 2006
Thighs
First assemble the blue facet close to the
foot, on the side of the hexagon, and on
the side of the thighs. Close the
hexagonal cover and the red facet on the
thigh.
Shins
First form a tube then
close both ends.
Front wheels and front spokes
Fold the front spokes then glue them against
the blue area of the front wheels. Make tire
sections one by one.
Feet
Assemble the heel area first, then
close the toe area.
Handle
The handle part is folded in half and glued.
Fork
Assemble the blue tube first, and then
assemble the upper portion.
*Assembling
the whole fork
at once causes
warping.
Weigh it down to make it flat
until it dries.
Insert the tip of the spoke into the tire and connect the
tire sections.
Make sure the tire is round before the glue dries.
*Rear wheels are assembled in the same way.
3
All right reserved, Copyright Murata Manufacturing Co.,Ltd. 2006
4
Saddle
The saddle should be box shaped.
Frame (front section)
Fold and assemble shape all
tubes without using glue then
apply glue.
Frame (rear section)
Fold the rear section of the
frame in a half and glue the
halves together. Press it
down with something heavy
to make it flat and let it dry.
Pedals
Fold the pedal in half and then apply
glue. Press it down with something
heavy to make it flat and let it dry.
Once the glue is dry, bend the tips.
Motor
The motor consists of a hexagonal
cylinder part and the part folded in
half before gluing.
Press down the folded part after
gluing to make sure it dries flat.
Chain drive
Fold the chain
drive part in half
and glue the
halves together.
Press it down with
something heavy
to keep it flat until
it dries.
Rear fender
Fold the rear
fender part in half
and glue the
halves together.
Press it down with
something heavy
to keep it flat until
it dries.
* Do not glue the two parts
together until the final stage of
bicycle assembly.
All right reserved, Copyright Murata Manufacturing Co.,Ltd. 2006
5
Main Bicycle Parts Assembly
Main MURATA BOY Parts Assembly
Insert the fork into
the front part of the
frame and glue them
together.
Glue the A and B marks of
the front wheel to the front
section of the frame where it
is marked A and B
respectively.
Glue the head mark on the head part
together with head mark on the neck part.
Glue the neck part to the neck mark of
the body part.
Glue the facet with D
on the saddle to facet
D on the frame.
Install the backpack on back
of the body part.
Glue the bottom part of the
body to the front half of the
saddle.
Glue the M and N
marks of the rear
wheel to the rear
section of the frame.
Glue the right and left shoulder
marks of the shoulder part with
the right and left shoulder marks of
the body part respectively.
All right reserved, Copyright Murata Manufacturing Co.,Ltd. 2006
Bend the rear fender to make a U shape.
Glue it to the O and P marks on the rear
section of the frame.
Glue the two motor parts
together at the L marks, and
glue it to the front of the rear
fender.
Glue the K mark of the chain drive
to the K mark of the rear section of
the frame.
Glue the J mark of a pedal to the J
mark of the chain drive.
Glue the left and right thigh
marks to the body, matching
their angles with the pedals.
Glue the I mark of a pedal to the I mark
of the rear section of the frame.
*Stand MURATA BOY against some
object to ensure that he dries in the
correct position.
Glue the bottom of the
wheels to the pedestal.
MURATA BOY
MURATA BOY
6
Final Bicycle Parts Assembly
All right reserved, Copyright Murata Manufacturing Co.,Ltd. 2006
Tabla de contenidos
