multicomp pro MP780053 Manual de usuario
1
Voltage Tester
Model No. MP780053
2
Read all instructions before using the appliance and retain for future reference.
• Please follow all safety operation instructions.
• Check probes and case insulation before using. If you nd any breakage
or abnormality, or you consider the device is broken, stop using the device
immediately.
• Test using a known live source in the AC voltage range to conrm the tester is
working properly before use.
• Use caution with voltages above 30VAC as a shock hazard may exist.
• Insulation type and thickness and other factors may effect the operation, use other
methods to verify live voltages if there is any uncertainty.
• Do not use the product for any purpose other than that for which it is designed.
• Turn the tester off when not in use to save the battery.
• Remove the battery if the meter is not to be used for long periods.
• Replace the battery as soon as the low battery warning appears to avoid possible
electric shock or personal injury caused by incorrect readings.
PRODUCT OVERVIEW
WHAT’S INCLUDED
• Voltage Tester
• Batteries.
• Instruction manual.
IMPORTANT SAFETY INFORMATION
OPERATION
1. Screw on battery cover
2. Flashlight
3. Flashlight ‘on/off’ button
4. 12V mode button
5. Tester ‘on/off’ button
6. LED indicators
7. Detector tip
8. Worklight 1
234
5
6
7
8
• Turning the tester on: Momentarily press the tester On/Off button (5). The
sounder will beep once and the green LED will illuminate to indicate that the tester
is on and ready for use.
• Turning the tester off: Momentarily press the On/Off button. The tester will beep
twice and the green LED will turn off.
• Turning the sounder off: With the tester off, press and hold the On/Off button until
the green LED is illuminated. The tester will now operate without the sounder. To
turn the sounder off when the tester is on, press and hold the On/Off button until the
green LED ashes. To turn the sounder back on, press and hold the On/Off button
until the green LED ashes and the sounder beeps.
• Verify Operation: Before using tester, make sure the green LED is glowing and
check the tester on a known live AC voltage that is within the dened detection
range of the tester.
3
CLEANING
• Clean the tester with a clean, soft cloth.
• Do not use any chemicals, abrasives or solvents that could damage the tester.
MAINTENANCE
1. Carefully unscrew the battery cap at the rear (ashlight end) of the tester.
2. Replace the batteries with two AAA 1.5V batteries observing the polarity.
3. Carefully align the 2 ashlight contact springs on the cap with the contacts above
the batteries.
4. Press the cover onto tester and rotate clockwise until engaged. Do not use
excessive force.
5. The IP67 dust and water ingress protection level is
determined by the correct tting of this cap.
NOTE: When batteries are loaded for the rst time,
please remove the white, rectangular security strip
before installing the batteries.
• High Voltage Mode (100 to 1000V AC): Place the tip of the tester near an AC
voltage. If the tester detects voltage within the dened detection range, the green
LED will turn off, the red LED will turn on, and the sounder will beep rapidly.
• Low Voltage Mode (12 to 1000V AC): Press and hold the 12V button (4). The
green LED will change to yellow to indicate the tester is in the low voltage mode.
While pressing the 12V button, place the tip of the tester near an AC voltage. When
AC voltage is detected, the yellow LED will turn off, the red LED will ash and the
sounder will beep.
NOTE: The ash rate and beeping rate will increase as the tester gets closer to the
voltage source. If the tester detects high voltage, it will automatically change over to
the high voltage mode: The red LED will change to a steady glow and the sounder will
beep rapidly. The tester cannot determine the actual voltage. The voltage level where
the tester switches from the low to high voltage mode is effected by insulation type and
thickness, distance from the voltage source, and other factors.
• Low Battery Indication: Replace the batteries if the green LED does not turn on.
When the tester is on and the batteries are too low for reliable operation, the beeper
will beep three times and the green LED will turn off indicating the tester is not
operational. Replace the batteries to restore operation.
• Auto Power Off: To conserve battery life, the tester will automatically turn off after
approximately 5 minutes of inactivity. When powering down, the beeper will beep
twice and the green LED will turn off.
• Flashlight: Momentarily press the Flashlight button (3) to turn the ashlight
on or off. To conserve battery life, the ashlight will automatically turn off after
approximately ve minutes. The beeper will beep twice as the ashlight turns off.
NOTE: If the battery voltage is too low to operate the ashlight, the tester will indicate
this condition by beeping three times and the ashlight will turn off. The voltage detector
has it’s own low battery threshold and may remain operational, verify it’s condition before
using the tester.
4
INFORMATION ON WASTE DISPOSAL FOR CONSUMERS OF ELECTRICAL &
ELECTRONIC EQUIPMENT.
These symbols indicate that separate collection of Waste Electrical and Electronic Equipment
(WEEE) or waste batteries is required. Do not dispose of these items with general household
waste. Separate for the treatment, recovery and recycling of the materials used. Waste batteries
can be returned to any waste battery recycling point which are provided by most battery retailers.
Contact your local authority for details of the battery and WEEE recycling schemes available in
your area. Made in China. LS12 2EN
Man Rev 1.0
SPECIFICATIONS
Detection voltage range 100V AC to 1000V AC, 12V to 1000V AC
Frequency range 50/60Hz
Batteries Two AAA 1.5V batteries
Operating temperature 0°C to 50°C (32°F to 122°F)
Storage temperature -10°C to 60°C (14°F to 140°F)
Humidity 80% max
Altitude 2000 meters
Pollution Degree 2
Safety Compliance CAT IV-1000V
Certied ATEX 2460
Designed and manufactured by CEM
Address: 19th Building, 5th Region, Baiwangxin Industry Park, XiLi,
Nanshan, Shenzen, China 518108
Tabla de contenidos
Otros manuales de Equipo de prueba de multicomp pro
multicomp pro
multicomp pro MP780426 Manual de usuario
multicomp pro
multicomp pro MP700005 Manual de usuario
multicomp pro
multicomp pro MP780052 Manual de usuario
multicomp pro
multicomp pro MP720774 Manual de usuario
multicomp pro
multicomp pro MP720645 Manual de usuario
multicomp pro
multicomp pro MP720012 Manual de usuario
multicomp pro
multicomp pro MP720854 Manual de usuario
multicomp pro
multicomp pro HDS-N Series Manual de usuario
multicomp pro
multicomp pro MP720644 Manual de usuario
multicomp pro
multicomp pro MP720024 Manual de usuario
multicomp pro
multicomp pro MP720105 Manual de usuario
multicomp pro
multicomp pro MP720009 Manual de usuario
multicomp pro
multicomp pro MP700110 Manual de usuario
multicomp pro
multicomp pro MP760855 Manual de usuario
multicomp pro
multicomp pro MP700499 Manual de usuario
multicomp pro
multicomp pro MP720780 Manual de usuario
multicomp pro
multicomp pro MP720025 Manual de usuario
multicomp pro
multicomp pro MP780834 Manual de usuario
multicomp pro
multicomp pro MP720856 Manual de usuario
multicomp pro
multicomp pro MP780051 Manual de usuario
Manuales populares de Equipo de prueba de otras marcas
SMART
SMART KANAAD SBT XTREME 3G Series Manual de usuario
Agilent Technologies
Agilent Technologies BERT Serial Manual de usuario
Agilent Technologies
Agilent Technologies N3280A Manual de usuario
Vernier
Vernier Go Direct Voltage Manual de usuario
Lifeloc
Lifeloc R.A.D.A.R. Manual de usuario
Fluke
Fluke T5-600 Instrucciones de funcionamiento e instalación
