MTX RANGER-10 Manual de usuario

MTX.COM

OWNER’S MANUAL

RANGER-10

POLARIS®RANGER®AMPLIFIED SUBWOOFER ENCLOSURE

MTX.COM

IMPORTANT NOTICE

If you have any questions regarding wire routing in a vehicle, please contact MTX Technical Support

at 1-800-225-5689.

When connecting power and ground wires ensure that the red power wire is fused at the point

where it is connected to the vehicle’s battery. Failure to do so can result in damage to the vehicle if a

short circuit develops between the vehicle connection point and the product.

PRODUCT INFORMATION

Model #

Serial #

Dealer’s Name

Date of Purchase

IN THE BOX

• RANGER-10AmpliedSubwooferEnclosure

• EBC and EBC Extension Wire

• Mounting Hardware

Top Mounting Bracket

90°Bottom Mounting Bracket

M6 14mm Bolt with Washer and Lock Washer

5⁄16 Self-tapping Screws

ST6.3 25mm Self-tapping Screw

ADDITIONAL ACCESSORIES NEEDED AND NOT INCLUDED

MTX recommends using StreetWires PS1K-10 amp kit which includes the following:

• Power and Ground Wire to Run to the Battery

• 20A ATC Fuse Holder

• Accessory Connection Wire

• RCA Cables to Connect to the Source

INSTALLATION TOOLS

The following is a list of suggested tools needed for installation:

• Torx - T40

• 3⁄8" Socket

• Flat Blade Screwdriver

• Pry Tool

• 1⁄8" Drill Bit

INTRODUCTION

ThankyouforpurchasingtheMTXAudioampliedsubwooferenclosuredesignedforthePolaris®

RANGER®.TheeasytoinstallsubwooferistheperfectdirecttbasssolutionforyourPolaris®

RANGER®. Congratulations and enjoy the ultimate audio experience with MTX!

FITS THE FOLLOWING VEHICLES

• RANGER®XP 570 / 900 (2014 and Up)

• RANGER®DIESEL (2014 and Up)

• RANGER®6X6 (2014 and Up)

• RANGER CREW®XP 570-6 (2014 and Up)

• RANGER CREW®XP 900-5 EPS / 900-6 EPS (2014 and Up)

• RANGER CREW®DIESEL (2014 and Up)

MTX.COM 3

FEATURES

• 10"All-WeatherAmpliedSubwooferEnclosure

• Integrated250-WattRMS/500-WattPeakPowerAmplier

• Integrated Power and Ground Connections

• Low Level Input with External Gain Control

• Dash Mount Bass Control Knob (Included)

• Mounts Underneath Driver’s Seat (2 Seat Model) or Underneath Driver’s Side Rear Seat

(4 Seat Model) - Direct Fit, No Cutting Required

SPECIFICATIONS

• RMS Power Handling: 250-Watts

• Peak Power Handling: 500-Watts

• Frequency Response: 31Hz - 130Hz

MTX.COM

INSTALLATION

Step 1 - Lift the driver’s seat up and remove the plastic tub. The tub will not be reused.

Step 2 - Remove the T40 screws from the driver’s side. The single cab RANGER uses four screws on

theoorarea,onescrewonthefrontfenderarea(thelowestscrew),andonescrewonthebackof

the side panel.

MTX.COM 5

The dual cab RANGERusestwoscrewsontheoorarea,onescrewonthefasciabelowtheseat,

and one screw on the back of the side panel.

Step 3 - Remove the front and rear locking pins.

MTX.COM

Step 4 - Loosenthepipeclamponthefuelllerpipewithaatbladescrewdriver.Thefuelllerpipe

should be able to be pulled from the rubber fuel pipe. Take care when doing so.

WARNING: Do not smoke during this step.

Step 5 - Carefullypullawaythesidepanelfromvehicle.Thegascap/fuelllerpipeisattachedto

the plastic side panel and will slide out of the rubber fuel pipe.

MTX.COM 7

Step 6 - Slide the long part of the enclosure into the vehicle frame above the gas tank. The subwoofer

will face the top of the gas tank. Two brass inserts will be visible when looking down from the top and

the MTX logo will be pointing towards the outside of the vehicle.

Step 7 - Remove the two T40 screws as shown above. These screws hold down the vehicle plastic

brace under the seat.

Step 8 - Line up the larger enclosure mounting bracket with the alignment holes for the vehicle

mounting screws. Using the T40 screws from Step 7 screw the bracket to the vehicle, hand tighten.

Attach the bracket to the two brass inserts in the top of the enclosure using the included M6 bolts

and washers, hand tighten.

MTX.COM

Step 9 - Line up the brass insert on the front of the enclosure with the hole in the vehicle frame. Using

the included M6 bolt and washer, attach the enclosure to the vehicle.

Step 10 - Tighten all M6 bolts into the enclosure as well as the T40 bolts holding the top enclosure

bracket to the vehicle.

Step 11 - The small 90°angle bracket attaches to the vehicle using the two pre drilled holes on the

frame. The two larger holes in the bracket are for the 5⁄16" self-tapping bolts. Secure the bracket to the

frame using the included bolts.Thebracketwillsitushwiththeenclosure.

MTX.COM 9

Step 12 - Attach the enclosure to the 90°angle bracket using the included ST6.3 self-tapping screws.

A 1⁄8" drill bit should be used to pre drill holes in the enclosure. Be careful not to strip them when

tightening into the enclosure material. Do not use an impact driver for these screws.

Step 13 -Now that the enclosure is securely tightened in place, the power and signal wires need to

be connected to the battery and signal source.

• The Red wire should be connected directly to the battery’s positive terminal and fused with a

20A fuse.

• The Black wire should be directly connected to the battery’s negative terminal.

• If your vehicle is equipped with the Polaris®busbar kit, the Red and Black wires can be

connected to the busbar under the hood. The Red wire will still need to be fused.

• The Blue wire can be connected to the ACC / Key Turn On located on the busbar of any vehicle.

Step 14 - Connect the RCA inputs to the signal source of your choice

Step 15 - Turn the unit on and check to make sure everything works. Set the gain using the gain pot

that is attached to the orange/grey wires. Set the gain to the bass level desired.

Step 16 - The included EBC can be connected and mounted to a desired location to allow easy trim

adjustment of the bass level after the gain has been set.

Step 17 - Replace all the parts and screws that have been removed to return the RANGER back to its

completely assembled state.

MTX.COM

NOTES:

Tabla de contenidos

Otros manuales de Subwoofer de MTX

MTX

MTX CANAM-10 Manual de usuario

MTX

MTX Thunder T8512-04 Manual de instrucciones

MTX

MTX CT12SW Manual de usuario

MTX

MTX Thunder TR7515-22 Manual de instrucciones

MTX

MTX Thunder TR4512-44 Manual de instrucciones

MTX

MTX TS9924-22 Manual de usuario

MTX

MTX CXP10 Manual de usuario

MTX

MTX Thunder 85 TS8512-22 Manual de usuario

MTX

MTX RTT12P Manual de usuario

MTX

MTX T684 Manual de instrucciones

MTX

MTX Thunder TS5510-22 Manual de instrucciones

MTX

MTX PROXP-20-SW Manual de usuario

MTX

MTX TRP8 Manual de usuario

MTX

MTX Thunder TS5510-44 Manual de instrucciones

MTX

MTX ThunderLink XT110P Manual de usuario

MTX

MTX LOLITA Manual de usuario

MTX

MTX Thunder AXE TXC6-0 Manual de usuario

MTX

MTX JACKHAMMER T9922-22 Manual de usuario

MTX

MTX CT8SW Manual de usuario

MTX

MTX MTX Thunder 6000 T61044A Manual de usuario

MTX

MTX MTX Thunder 4000 T4104A Manual de usuario

MTX

MTX Thunder TR4510-44 Manual de instrucciones

MTX

MTX Thunder T9512-44 Manual de usuario

MTX

MTX JackHammer Manual de usuario

Manuales populares de Subwoofer de otras marcas

Sony

Sony XS-AW8 Manual de usuario

Sony

Sony XS-L836 Manual de usuario

B&C Speakers

B&C Speakers 15 HPL 76W Manual de usuario

Velodyne

Velodyne DD-18+ Manual de usuario

Sonance

Sonance Cinema Series SUB 10-150 Manual de usuario

Hifonics

Hifonics HW-12 Guía de inicio rápido

Magnat Audio

Magnat Audio ADR 130 BP Manual de usuario

Blitz

Blitz BZP106 Manual de usuario

Technics

Technics SB-AS500 Manual de usuario

Lyngdorf

Lyngdorf BW-2 Manual de usuario

Lyngdorf

Lyngdorf BW-3 Manual de usuario

Pyle Pro

Pyle Pro PYLE PRO PDW15125 Manual de usuario

REL Acoustics

REL Acoustics Q Series Manual de usuario

Pioneer

Pioneer Elite S-W1EX Manual de usuario

L-Acoustics

L-Acoustics KIVA SB15M Guía de inicio rápido

B&C Speakers

B&C Speakers Woofer 12 HPL 76 Manual de usuario

KEF

KEF KUBE 200 Manual de usuario

Yamaha

Yamaha SW500 Manual de usuario