MSI pc2pc bluetooth Manual de usuario
Version 1.4
Nov. 2003
G52-W6967X3
MICRO-STAR INT’L
FCC-B Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a class B
digital device, pursuant to part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Op-
eration of this equipment in a residential area is likely to cause harmful interference,
in which case the user will be required to correct the interference at his own expense.
Notice 1
The changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Notice 2
Shielded interface cables and A.C. power cord, if any, must be used in order to
comply with the emission limits.
VOIR LA NOTICE D’INSTALLATION AVANT DE RACCORDER AU
RESEAU.
FCC ID: I4L-MS6967/MS6968
This device complies with part 15 of the FCC Rules. Opera-
tion is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) This de-
vice must accept any interference received, including inter-
ference that may cause undesired operation.
FCC Requirement
This equipment complies with Part 68 of the FCC Rules. On the bottom of this
equipment is a label that contains, among other information, the FCC registration
Number, Ringer Equivalence Number (REN) and USOC jack type for this
equipment. You must, upon request, provide this information to your telephone
company.
An FCC compliant telephone cord and modular jack is provided with this equipment.
This equipment is designed to be connected to the telephone network or premise
wiring use a compatible modular jack which is Part 68 compliant. See installation
instructions for details.
The REN is useful to determine the quantity of devices you may connect to your
telephone line and still have all of those devices ring when your telephone number
is called. In most, but not all areas, the sum of the REN of all devices connected
to on line should not exceed five (5.0). To be certain of the number of devices you
may connect to your line, as determined by the REN, you should contact your local
telephone company to determine the maximum REN for your calling area. If your
telephone equipment causes harm to the telephone network, the Telephone Com-
pany may discontinue your service temporarily. If possible, they will notify you
in advance, but if advance notice is not practical, you will be notified as soon as
possible. You will be informed of your right to file a complaint with the FCC.
Your telephone company may make changes in its facilities, equipment, operations
or procedures that could affect the proper functioning of your equipment. If they
do, you will be notified in advance to you an opportunity to maintain uninter-
rupted telephone service.
If you experience trouble with this telephone equipment, please contact MICRO-
STAR INTERNATIONAL for information on obtaining service or repairs. The
telephone company may ask that you disconnect this equipment from the network
until the problem has been corrected or until you are sure that the equipment is not
malfunctioning.
This equipment may not be used on coin service provided by the telephone com-
pany. Connection to party lines is subject to stat tariffs.
Copyright Notice
The material in this document is the intellectual property of MI-
CRO-STAR INTERNATIONAL. We take every care in the prepa-
ration of this document, but no guarantee is given as to the correct-
ness of its contents. Our products are under continual improve-
ment and we reserve the right to make changes without notice.
Trademarks
All trademarks used in this manual are the sole property of their
respective owners.
Pentium is a registered trademark of Intel Corporation.
Windows is a registered trademark of Microsoft Corporation.
Revision History
Revision Revision History Date
V 1.2 Software update Feb. 2003
V 1.3 Adding “Human Interface Nov. 2003
Device”
V1.4 Adding “Security Code” Nov. 2003
Important Safety Precautions
Always read and follow these basic safety precautions carefully when handling
any piece of electronic component.
1. Keep this User’s Manual for future reference.
2. Keep this equipment away from humidity.
3. Lay this equipment on a reliable flat surface before setting it up.
4. The openings on the enclosure are for air convection hence protects
the equipment from overheating.
5. All cautions and warnings on the equipment should be noted.
6. Never pour any liquid into the opening that could damage or cause
electrical shock.
7. If any of the following situations arises, get the equipment checked by
a service personnel:
zz
zz
zThe USB cable is damaged
zz
zz
zLiquid has penetrated into the equipment
zz
zz
zThe equipment has been exposed to moisture
zz
zz
zThe equipment has not work well or you can not get it work
according to User’s Manual
zz
zz
zThe equipment has dropped and damage
zz
zz
zIf the equipment has obvious sign of breakage
8. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT
UNCONDITIONED, STORAGE TEMPERATURE ABOVE 600 C OR
BELOW -200C, IT MAY DAMAGE THE EQUIPMENT.
CONTENTS
1. Introduction ................................................................................ 1
1.1 Bluetooth Technology ........................................................... 1
1.2 MSI™ PC2PC Bluetooth ...................................................... 1
1.3 Hardware Specifications ......................................................... 2
2. Installation.................................................................................. 5
2.1 Package Checkup .................................................................... 5
2.2 Software Installation .............................................................. 6
2.3 Hardware Installation ............................................................. 9
3. Software Operations -- My Bluetooth Places................. 13
3.1 Introduction........................................................................... 13
3.2 Basic Operations ................................................................... 19
3.3 Configure Bluetooth ............................................................. 26
3.4 Security .................................................................................. 74
3.5 Troubleshooting.................................................................... 78
4. Technical Support.................................................................... 83
5. Glossary ..................................................................................... 85
User’s Guide
1
1. Introduction
1.1 Bluetooth Technology
The term “Bluetooth” refers to a worldwide standard for the
wireless exchange of data between two devices. In order to ex-
change data, two Bluetooth devices must establish a connection.
Before a connection is established, one device must request a con-
nection with another. The second device accepts (or rejects) the
connection.
The originator of the request is known as the client. The
device that accepts (or rejects) the request is known as the server.
Many Bluetooth devices can act as both client and server.
A client Bluetooth device runs a software program that re-
quests a connection to another device as part of its normal operation.
For example, the program may request a connection to a remote
computer, a printer, or a modem. Becoming a Bluetooth client
normally requires an action by the device operator, such as an
attempt to browse a remote computer, print a file, or dial out on a
modem.
Every Bluetooth device that provides a service must be pre-
pared to respond to a connection request. Bluetooth software is
always running in the background on the server, ready to respond to
connection requests.
1.2 MSI™ PC2PC Bluetooth
MSI™ PC2PC Bluetooth provides wireless technology that
revolutionizes personal connectivity. It is the solution for the seam-
less integration of Bluetooth technology into personal computers,
2
PC2PC Bluetooth
1.3 Hardware Specifications
enabling short-range wireless connections between desktop/laptop
computers, Bluetooth-enabled peripherals (printers, faxes,...), port-
able handheld devices, and connectivity to the Internet.
Bluetooth Transceiving Key/Module
General
H/W Interface USB
Bluetooth Spec. Ver. 1.1
Compliance
Throughput About 723Kbps (data channels)
Operating Volt. 5Vfrom USB interface
Operating Range Up to 200M for open space (depending on the environment)
Regulatory Approval FCC, CE, BQB (Bluetooth Qualified), BSMI
Temperature Storage temp: -10oC~+70oC
Operating temp: -10oC~+70oC
Radio
Spread Spectrum Frequency Hopping Spread Spectrum (FHSS)
Compliant with FCC part 15
Frequency Range 2.4~2.4835GHz (2.4GHz ISM Band)
RF Channels 79-channel system for USA, Japan, and Europe
(except France, 23-channel system for France)
Modulation GFSK, BT=0.5
Output Power Class Bluetooth Power Class 1
Output Power +18dBm(Max.)
Receiver Sensitivity Better than -90dBm with BER < 0.1%
Max Input Level -20dBm
Power Control Yes
Base Band
Physical Links Support ACL link
User’s Guide
3
Network Capabilities Support piconet point-to-point and point-to-
multipoint connections
Link Manager
3-slot Packets Yes
5-slot Packets Yes
Slot Offset Yes
Timing Accuracy Yes
Switch Yes
Hold Mode Yes
SniffMode Yes
Test Mode Yes
Park Mode Yes
RSSI Yes
Power Control Yes
Authentication Yes
Encryption Yes
Software
System Support Windows®2000/ME/98/XP
Profile Support Generic Access Profile/Service Discovery
Profile/Serial Port Profile/Dial-Up Networking
Profile/Fax Profile/LAN Access Profile/Generic
Object Exchange Profile/File Transfer Profile/
Object Push Profile/Synchronization Profile/
Personal Area Network Profile/Hard Cable
Replacement Profile
4
PC2PC Bluetooth
NOTES
Tabla de contenidos
