MSI MS-7072 Manual de usuario
i
MS-7072 Mainboard
ii
Copyright Notice
The material in this document is the intellectual property of MICRO-STAR
INTERNATIONAL. We take every care in the preparation of this document, but no
guarantee is given as to the correctness of its contents. Our products are under
continual improvement and we reserve the right to make changes without notice.
Trademarks
All trademarks are the properties of their respective owners.
AMD, Athlon™, Athlon™ XP, Thoroughbred™, and Duron™ are registered trade-
marks of AMD Corporation.
Intel®and Pentium®are registered trademarks of Intel Corporation.
PS/2 and OS®/2 are registered trademarks of International Business Machines
Corporation.
Microsoft is a registered trademark of Microsoft Corporation. Windows®98/2000/NT/
XP are registered trademarks of Microsoft Corporation.
NVIDIA, the NVIDIA logo, DualNet, and nForce are registered trademarks or trade-
marks of NVIDIA Corporation in the United States and/or other countries.
Netware®is a registered trademark of Novell, Inc.
Award®is a registered trademark of Phoenix Technologies Ltd.
AMI®is a registered trademark of American Megatrends Inc.
Kensington and MicroSaver are registered trademarks of the Kensington Technology
Group.
PCMCIA and CardBus are registered trademarks of the Personal Computer Memory
Card International Association.
iii
1. Always read the safety instructions carefully.
2. Keep this User’s Manual for future reference.
3. Keep this equipment away from humidity.
4. Lay this equipment on a reliable flat surface before setting it up.
5. The openings on the enclosure are for air convection hence protects the equip-
ment from overheating. Do not cover the openings.
6. Make sure the voltage of the power source and adjust properly 110/220V be-
fore connecting the equipment to the power inlet.
7. Place the power cord such a way that people can not step on it. Do not place
anything over the power cord.
8. Always Unplug the Power Cord before inserting any add-on card or module.
9. All cautions and warnings on the equipment should be noted.
10. Never pour any liquid into the opening that could damage or cause electrical
shock.
11. If any of the following situations arises, get the equipment checked by a service
personnel:
hThe power cord or plug is damaged.
hLiquid has penetrated into the equipment.
hThe equipment has been exposed to moisture.
hThe equipment has not work well or you can not get it work according to
User’s Manual.
hThe equipment has dropped and damaged.
hThe equipment has obvious sign of breakage.
12. Do not leave this equipment in an environment unconditioned, storage
temperature above 600 C (1400F), it may damage the equipment.
Safety Instructions
CAUTION: Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the
manufacturer.
Mainboard HardwareMainboard Hardware
Mainboard HardwareMainboard Hardware
Mainboard Hardware
1.1 Mainboard Layout1.1 Mainboard Layout
1.1 Mainboard Layout1.1 Mainboard Layout
1.1 Mainboard Layout
1.2 CPU1.2 CPU
1.2 CPU1.2 CPU
1.2 CPU
1.3 Memory1.3 Memory
1.3 Memory1.3 Memory
1.3 Memory
1.4 Power Supply1.4 Power Supply
1.4 Power Supply1.4 Power Supply
1.4 Power Supply
1.5 Front Panel1.5 Front Panel
1.5 Front Panel1.5 Front Panel
1.5 Front Panel
1.6 Back Panel1.6 Back Panel
1.6 Back Panel1.6 Back Panel
1.6 Back Panel
1.7 Connectors1.7 Connectors
1.7 Connectors1.7 Connectors
1.7 Connectors
1.8 Jumper1.8 Jumper
1.8 Jumper1.8 Jumper
1.8 Jumper
1.9 Slots1.9 Slots
1.9 Slots1.9 Slots
1.9 Slots
1-2
Chapter 1
1.1Mainboardlayout
MS-7072 Mainboard
BATT
+
DIMM1 DIMM2
JCMOS
J1
JFP1
CN16
ATX
Power Supply
PCISlot1
MDCT2000
MHT2007
MHT2008
CNT2011
VIA
VT6307
RTL8100C
smsc
LPC47M997-NR
Codec
MINIPCI1
IDE2
IDE1 SATA1
JPW1
SYSFAN1
CPUFAN1
Top:COMPort
Bottom:VGAPort
Top:LANJack
Bottom:USBports
USBports
TV-out(S)connector
SPDIFIN1
AUDIO1
AUDIO2
USBT2003USBT2000
J1394-1 J1394-2
AGPSlot
T:
M:
B:
Line-In
Line-Out
Mic
T:RS-Out
M:CS-Out
B:SPDIFOut
ATI
Radeon
RS350
ATI
IXP300
SB300
BIOS CRT2000
JUSBT20001
1-3
Mainboard Hardware
1.2CPU
This mainboard supports Intel® P4 Northwood up to 3.2GHz and Prescott up to
3.4GHz. The mainboard uses a CPU socket called PGA478 for easy CPU installation.
When you are installing the CPU, make sure the CPU has a heat sink and a cooling fan
attached on the top to prevent overheating. Remember to peel off the sticker before
you install the CPU cooler. For information on how to install the CPU and cooler, refer
to Quick Installation Guide.
The mainboard provides 2 slots for 184-pin DDR SDRAM
DIMM (Double In-Line Memory Module) modules and supports the
memory size up to 2GB. You can install DDR400/DDR333/DDR266
modules into the DDR DIMM slots.
1.3 Memory
DIMM1 DIMM2
Note:
1. Read the instructions on the cooler before you start the installation.
2. Overheating will seriously damage the CPU and system, always make
sure the cooling fan can work properly to protect the CPU from overheating.
DIMM Module Combination
Install at least one DIMM module on the slots. You can install either single- or
double-sided modules in any order to meet your own needs. Memory modules can be
installed in any combination as follows:
S: Single Side
D: Double Side
Slot MemoryModule Total Memory
DIMM1 DDR S/D 64MB~1GB
(Bank 0 & 1)
DIMM2 DDR S/D 64MB~1GB
(Bank 2 & 3)
Maximum System Memory Supported 64MB~2GB
1-4
Chapter 1
1.4 Power Supply
The system is equipped with a 220W (PFC) ATX power supply. The power
cord of power supply has been connected to the connector ATX1 on the mainboard
when shipped out. Except the 20-pin connector ATX1, you can find another 4-pin
power connector JPW1 on the mainboard.
PIN SIGNAL
11 3.3V
12 -12V
13 GND
14 PS_ON
15 GND
16 GND
17 GND
18
19 5V
20 5V
PIN SINGAL
1 3.3V
2 3.3V
3 GND
45V
5 GND
65V
7 GND
8 PW_OK
9 5V_SB
10 12V
ATX1 Pin Definition
ATX1
20
10 1
11 1
3
4
2
JPW1
PIN SINGAL
1 GND
2 GND
3 12V
4 12V
JPW1 Pin Definition
1-5
Mainboard Hardware
1.5 Front panel
The Front Panel is independent and extended from the mainboard. It’s con-
nected to the Front I/O Connector on the mainboard. You can find the following ports
on the Front Panel.
IEEE 1394 Port: J1394-2
The mainboard provides two IEEE 1394 ports. This smaller one is designed
for you to connect the IEEE 1394 device with external power. The IEEE 1394 high-
speed serial bus complements USB by providing enhanced PC connectivity for a
wide range of devices, including consumer electronics audio/video (A/V) appliances,
storage peripherals, other PCs, and portable devices.
Software Support
IEEE 1394 Driver is provided by Windows®98 SE, Windows®XP, Win-
dows®ME and Windows®2000. Just plug in the IEEE 1394 connector into
the port. These Operating Systems will install the driver for IEEE 1394.
IEEE 1394 Port: J1394-1
The bigger 6-pin IEEE 1394 Port on the front panel is designed for you to
connect to IEEE 1394 devices without external power. That means the mainboard can
provide the power for the devices connected to this port.
Optical SPDIF-In Mic-InHead-Phone
USB x 2
J1394-1 J1394-2
1-6
Chapter 1
USB Ports
The mainboard provides a UHCI (Universal Host Controller Interface) Univer-
sal Serial Bus root for attaching USB devices such as keyboard, mouse or other
USB-compatible devices. You can plug the USB device directly into the connector.
PIN SIGNAL DESCRIPTION
1 VCC +5V
2 -Data 0 Negative Data Channel 0
3 +Data 0 Positive Data Channel 0
4 GND Ground
5 VCC +5V
6 -Data 1 Negative Data Channel 1
7 +Data 1 Positive Data Channel 1
8 GND Ground
USB Port Description
Mic-in/Head-Phone
Mic-in is a connector for stereo microphone. Head-Phone is a connector for
Speakers or Headphones.
OPTICAL SPDIF-in
The OPTICAL connector allows you to receive the audio file of SPDIF inter-
face for recording and playing.
The SPDIF (Sony & Philips Digital Interface) is developed jointly by the Sony
and Philips corporations. A standard audio file transfer format, SPDIF allows the
transfer of digital audio signals from one device to another without having to be
converted first to an analog format.
1-7
Mainboard Hardware
1.6 Back panel
The Back Panel provides the following ports:
Serial Port
The mainboard offers a 9-pin male DIN serial port. The port is 16550A high
speed communication ports that sends/receives 16 bytes FIFOs. You can attach a
serial mouse or other serial devices directly to the connector.
9-Pin Male DIN Connector
1 2 3 4 5
6 7 8 9
PIN SIGNAL DESCRIPTION
1 DCD DataCarryDetect
2 SIN SerialInorReceiveData
3 SOUT SerialOutorTransmitData
4 DTR DataTerminal Ready
5 GND Ground
6 DSR DataSetReady
7 RTS RequestToSend
8 CTS ClearToSend
9 RI RingIndicate
Pin Definition
VGA Port USB
CS-Out
SPDIF-Out
(optical)
RS-Out
Line-In
Mic-in
LAN Port
Serial Port
Line-Out
Tabla de contenidos
Otros manuales de Placa madre de MSI
MSI
MSI Z170-A PRO Manual de usuario
MSI
MSI 880GMA-E53 Series Manual de usuario
MSI
MSI 661FM2-V ILSR Manual de usuario
MSI
MSI X58A-GD45 series Manual de usuario
MSI
MSI P7N SLI-FI - Motherboard - ATX Manual de usuario
MSI
MSI B450 TOMAHAWK MAX Manual de usuario
MSI
MSI MEG Z490 ACE Manual de usuario
MSI
MSI MPG X570S EDGE MAX WIFI Manual de usuario
MSI
MSI K9A2GM V2 Series Manual de usuario
MSI
MSI B75MA-E2 Manual de usuario
MSI
MSI 7B84-017R Manual de usuario
MSI
MSI H6M-P32/W8 series Manual de usuario
MSI
MSI MPG Z490 GAMING EDGE WIFI Manual de usuario
MSI
MSI 865PE Neo2-P Platinum Edition Manual de usuario
MSI
MSI MS-6309 Manual de usuario
MSI
MSI K9N6PGM2-V2 - Motherboard - Micro ATX Manual de usuario
MSI
MSI MS-7181 Manual de usuario
MSI
MSI MS-7329 Manual de usuario
MSI
MSI MPG B550 GAMING PLUS Manual de usuario
MSI
MSI PRO B760M-E DDR4 Manual de usuario
Manuales populares de Placa madre de otras marcas
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manual de usuario
Gigabyte
Gigabyte GA-9IVDT Manual de usuario
Texas Instruments
Texas Instruments ADS8372EVM Manual de usuario
Commell
Commell MS-C73 Manual de usuario
IBT Technologies
IBT Technologies MB860 Manual de usuario
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manual de usuario
