MSI MS-6301 Manual de usuario
CHAPTER 1 INTRODUCTION
1-1
The MS-6301 ATX CA8 mainboard is a high-performance computer
mainboard based on Intel®820 chipset. The MS-6301 is designed for the
Intel®PentiumTM II/III processor for high-end business/personal desktop
markets.
The Intel®820 chipset is the first generation chipset for the Intel®Pentium®
II/III processor. An integrated centralized memory arbiter allocates memory
bandwidth to multiple system agents to optimize system memory utilization.
A new chipset component interconnect, the hub interface, is designed into
the Intel 820 chipset to provide an efficient communication channel between
the memory controller hub and I/O controller hub.
The Intel 820 chipset contains four core components: the Memory Control-
ler Hub (MCH), Memory Translator Hub (MTH), the I/O Controller Hub
(ICH) and the Firmware Hub (FWH). The MCH integrates a 100MHz/
133MHzCPUFSB,andafix100MHzSDRAMcontrollerandhigh-speedhub
interface for communication with the ICH. The ICH integrates an Ultra ATA/
66(ICH)controller, USBhostcontroller, LPC interface controller,FWH
inteface conroller, PCI interface controller, AC’97 digital controller and a hub
interface for communication with the MCH.
The Intel®82802 Firmware Hub (FWH) component is part of the Intel®820
chipset. The FWH is key to enabling future security and manageability
infrastructure for the PC platform.
Chapter 1
INTRODUCTION
CHAPTER 1 INTRODUCTION
1-2
1.1 Mainboard Features
CPU
lSupport Intel®Pentium®II/III&Coppermine100/133MHzFSBprocessor.
lSupport350/400/450/500/533/600MHzorhigherprocessor
Chipset
lIntel®820Caminochipset.(324BGA)
-Optimized for Pentium III processor
-AGP4x/2x universal slot
-Support 100/133MHz FSB
lIntel®ICHchipset. (241 BGA)
- AC’97 Controller Integrated
- 2 full IDE channels, up to ATA66
- Low pin count interface for SIO
lIntel®MTHchipset. (241 BGA)
FrontSideBus (FSB)
l100/133MHz clocks are supported.
MainMemory
lSupports three 168-pin DIMM sockets.
lSupportsa maximumSDRAM memorysizeof 512MBor 1GB(32Mx4)
registered DIMM only.
lSupport only SDRAM without ECC Function.
Slots
lOne AMR (Audio Modem Riser)
lOne AGP (Accelerated Graphics Port) slot.
- AGP specification compliant
- AGP66/133/266MHzdevicesupport
lFive 32-bit Master PCI Bus slots and one 16-bit ISA slot(optional).
lSupports 3.3v/5v PCI bus Interface.
Note: If there’s onboard Hardware Audio or LAN. The PCI slot 1 and PCI
slot 5 will be shared.
CHAPTER 1 INTRODUCTION
1-3
On-BoardIDE
lAn IDE controller on the ICH chipset provides IDE HDD/CD-ROM with
PIO, Bus Master and Ultra DMA/66 operation modes.
lCan connect up to four IDE devices.
On-BoardPeripherals
lOn-BoardPeripherals include:
- 1 floppy port supports 2 FDD with 360K, 720K, 1.2M, 1.44M and
2.88Mbytes.
-2serialport (COMA + 1 COMB)
- 1 parallel port supports SPP/EPP/ECP mode
- 2 USB ports
- 1 IrDA connector for SIR.
- 1 LAN port
Audio
lICH chip integrated
lCreativeCT5880.(Optional)
- 64 Voice WaveTable Synthesizer
- Sound Library of over 4000 different sounds
-SupportSPDIF (AC3)
- Support Microsoft Direct Sound, Direct Sound 3D, Direct Music,
and A3DAPI.
Network (Reserved)
lIntel8255910/100M Ethernet (optional)
- WFW baseline & NET PC specs compliant
- Advanced Power Management (ACPI support)
- ARP& Flexible framefiltering
- Software drivers are backwards compatible
- IP checksumming in hardware
- Alert on LAN II(optional)
CHAPTER 1 INTRODUCTION
1-4
BIOS
lThe mainboard BIOS provides “Plug & Play” BIOS which detects the
peripheral devices and expansion cards of the board automatically.
lThe mainboard provides a Desktop Management Interface(DMI) function
which records your mainboard specifications.
lCPU Voltage setting through BIOS
lFWH Flash BIOS Protect
Dimension
lATXFormFactor: 30.5cmx21cm
Mounting
l6 mounting holes.
Otherfeatures
lCPU core/bus ratio & FSB frequencies setting through BIOS.
lDiagnostic LED system status display
lReset button protect
lKeyboard/Mouse Power on function
lSupport suspend to RAM (STR)
CHAPTER 1 INTRODUCTION
1-5
1.2 Mainboard Layout
PCI SLOT 3
PCI SLOT 2
PCI SLOT 1
ATX
Power Supply
Intel
820
chipset
DIMM 2(shared)
Top: mouse
Bottom:
keyboard
Top: LAN
(optional)
DIMM 1
IDE2
Bottom:
USBPorts
IDE1 FDD
ICH
J11
JFP1
JP1
JGS1
CD_IN
AUX_IN
PSFAN
BATT
+
Top: LPT
Bottom:
COMA
COMB
Top: Midi/
GamePort
Bottom:
Line-Out
Line-In
Mic
MS-6301 ATX CA8 Mainboard
MODEM_IN
CPUFAN
JVSB1
AMR
AGP Slot 1
JBAT1
SW2
JMDM1
DIMM 2(shared)
PCI SLOT 4
PCI SLOT 5
ISA SLOT 1
SYSFAN
JP4 FWH
JRMS1
J7
JGL1
JP2
J6
SW1
J5
J13
Intel
82559
(optional)
Creative
CT5880 JP3
WOL
JSTR
MTH
JP6
Slot 1
CHAPTER 2 HARDWARE INSTALLATION
2-1
Chapter 2
HARDWARE INSTALLATION
2.1 Central Processing Unit: CPU
Step 1: Install the Retention Mechanism.
Attach the Retention Mechanism to the Mainboard. Push the Plastic
lock to secure the Retention Mechanism into the mainboard.
Secure the processor by
pulling up the Retention
Mechanism Processor
Lock
Insert the processor
like inserting a PCI or
an ISA card
To release the
processor, push the
Retention Mechanism
Processor lock down
Step 2: Install the Processor.
Insert the Processor like inserting a PCI or an ISA card.
Step 3: Lock the Processor.
Lock the processor by pulling up the Retention Mechanism
processor lock shown above.
Note: The Retention Mechanism processor lock can only be used
with S.E.C.C.2 and S.E.P.P.processor.
2.1-1 Processor Installation Procedure
CHAPTER 2 HARDWARE INSTALLATION
2-2
2.1-2 CPU Core Speed Derivation Procedure
The mainboard CPU Core/Bus ratio and CPU Bus Frequency can
both be set through BIOS setup
If CPUClock = 100MHz
Core/Bus ratio = 4
then CPU core speed = Host Clock x Core/Busratio
= 100MHz x 4
= 400MHz
CHAPTER 2 HARDWARE INSTALLATION
2-3
2.1-3 Overclocking Jumper: SW1
Overclocking is operating a CPU/Processor beyond its specified
frequency. SW1 jumper is used for overclocking.
SW1
SW1 Function
Short
Open
Automatically detect CPU
Bus Frequency
Allows CPU overclocking.
Set 100MHz to 133Mhz
CHAPTER 2 HARDWARE INSTALLATION
2-4
2.1-4 Clocking Jumper for 66MHz (FSB) processor: SW2
This jumper is used to enabled 66MHz (FSB) processor. To be able to
used 66MHz(FSB) processor, you need to set this jumper.
SW2
SW2 Function
Short
Open
Default (if 66MHz FSB processor
is installed, the system will be
unabled to boot)
Allows 66MHz (FSB)
processor to run at
100MHz
CHAPTER 2 HARDWARE INSTALLATION
2-5
2.1-5 CPU Core/Bus Ratio strap to Safe Mode: JP3
This jumper is used to adjust the CPU core/ratio to safe mode.
JP3
JP3 Function
Short
Open
Safe Mode
(Core/Bus Ratio by 2)
Core/Bus Ratio in ICH
Register (Default)
Warning: If CPU Core/Bus ratio is set too high that the system hang.
Short pin JP3, then restart the system until boot up, the
CPU core/bus ratio will be set to the default setting by 2.
Properly shutdown the system, and remove the short on
JP3.
Tabla de contenidos
Otros manuales de Placa madre de MSI
MSI
MSI BIG BANG MARSHAL (B3) Manual de usuario
MSI
MSI MS-6334 Manual de usuario
MSI
MSI Z87 MPOWER MAX Manual de usuario
MSI
MSI EFINITY Series Manual de usuario
MSI
MSI B85M GAMING Manual de usuario
MSI
MSI Z77A Manual de usuario
MSI
MSI MEG X670E GODLIKE Manual de usuario
MSI
MSI 915P Neo2 Manual de usuario
MSI
MSI 865G Neo2 Manual de usuario
MSI
MSI MS-6799 Manual de usuario
MSI
MSI Z68A-G45 Series Manual de usuario
MSI
MSI PH61A-P35 (B3) Manual de usuario
MSI
MSI KA780GM Series Manual de usuario
MSI
MSI B450M MORTAR MAX Manual de usuario
MSI
MSI MS-6198 Manual de usuario
MSI
MSI H55-GD65 Series Manual de usuario
MSI
MSI B75MA-P33 series Manual de usuario
MSI
MSI B450M BAZOOKA Manual de usuario
MSI
MSI X299M GAMING PRO CARBON AC Manual de usuario
MSI
MSI PRO Z790-P WIFI DDR4 Manual de usuario
Manuales populares de Placa madre de otras marcas
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manual de usuario
Gigabyte
Gigabyte GA-9IVDT Manual de usuario
Texas Instruments
Texas Instruments ADS8372EVM Manual de usuario
Commell
Commell MS-C73 Manual de usuario
IBT Technologies
IBT Technologies MB860 Manual de usuario
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manual de usuario
