MSI MS-6178 Manual de usuario

CHAPTER 1 INTRODUCTION

1-1

The MS-6178 Micro ATX WH5 mainboard is a high-performance computer

mainboardbasedonIntel®810(810/810DC100/810e)chipset. TheMS-6178

is designed for the Intel®Pentium II/III or CeleronTM processor for inexpen-

sive business/personal desktop markets.

The Intel®810 chipset is the first generation Integrated Graphics chipset for

the Intel®CeleronTM processor. The graphics accelerator architecture

consists of dedicated multi-media engines executing in parallel to deliver

high performance 3D, 2D, and motion compensation video capabilities. An

integrated centralized memory arbiter allocates memory bandwidth to

multiple system agents to optimize system memory utilization. A new

chipset component interconnect, the hub interface, is designed into the Intel

810 chipset to provide an efficient communication channel between the

memory controller hub and I/O hub controller.

The series of Intel®810 chipset contains three core components: the

GraphicsandMemoryController Hub (GMCH), the I/O Controller Hub (ICH)

andthe Firmware Hub (FWH). The GMCH integrates a 66/100MHz for 810

and810DC100and66/100/133MHzfor810e,P6familysystembuscontrol-

ler, 2D/3D graphics accelerator, 100MHz SDRAM controller and high-speed

hub interface for communication with the ICH. The ICH integrates an Ultra

ATA 33(ICHO)/66(ICH) controller, USBhostcontroller,LPCinterface

controller,FWHinterfaceconroller, PCI interface controller,AC’97digital

controller and a hub interface for communication.

The Intel®82802 Firmware Hub (FWH) component is part of the seried of

Intel®810 chipset. The FWH is key to enabling future security and manage-

ability infrastructure for the PC platform.

Chapter 1

INTRODUCTION

CHAPTER 2 HARDWARE INSTALLATION

2-1

CPU

Chapter 2

HARDWARE INSTALLATION

2.1 Central Processing Unit: CPU

The mainboard operates with Intel®CeleronTM processor. The mainboard

uses a CPU socket called Socket 370 for easy CPU installation. The CPU

should always have a Heat Sink and a cooling fan attached to prevent

overheating.

3. Press the lever down to

complete the installation.

2. Locate Pin 1 in the socket

and look for the white dot or

cut edge in the CPU. Match

Pin 1 with the white dot/cut

edge. Then, insert the CPU.

It should insert easily.

OpenLever

Pin1

Sliding

Plate

White dot/

Cut edge

Lever

1. Pull the lever sideways away

from the socket. Then, raise

the lever up to a 90-degree

angle.

Pin1

2.1-1 CPU Installation Procedures

CHAPTER 3 AWARD®BIOS SETUP

3-1

Chapter 3

AWARD®BIOS SETUP

Award®BIOS ROM has a built-in Setup program that allows users to modify

the basic system configuration. This type of information is stored in

battery-backed RAM (CMOS RAM), so that it retains the Setup information

when the power is turned off.

CHAPTER 4 AMI

BIOS USERS GUIDE

4-1

Chapter 4

AMI®BIOS USER’S GUIDE

The system configuration information and chipset register information is

stored in the CMOS RAM. This information is retained by a battery when

the power is off. Enter the BIOS setup (if needed) to modify this information.

The following pages will describe how to enter BIOS setup, and all about

options.

CHAPTER 4 AMI

BIOS USERS GUIDE

4-2

2. When the “Hit <DEL>” message appears, press <DEL> key to

enter the BIOS setup screen.

3. After pressing <DEL> key, the BIOS setup screen will appear.

AGIOMS VXXX XXXXXX

Hit <DEL> if you want to run setup

61-XXXX-001169-00111111-071592-i82440FX-H

4.1 Enter BIOS Setup

EntertheAMI®setupProgram’sMainMenuasfollows:

1. Turn on or reboot the system. The following screen appears with

a series of diagnostic check.

Note: If you don’t want to modify CMOS original setting, then don’t press any

key during the system boot.

CHAPTER 4 AMI

BIOS USERS GUIDE

4-3

Standard CMOS Setup

Advanced CMOS Setup

Advanced Chipset Setup

Power Management Setup

PCI/Plug and Play Setup

Peripheral Setup

Hardware Monitor Setup

Auto-Detect Hard Disks

Change User Password

Change Supervisor Password

Change Language Setting

Auto Configuration with Optimal Settings

Auto Configuration with Fail Safe Settings

Save Settings and Exit

Exit without Saving

4. Use the <Up> and <Down> key to move the highlight scroll up or

down.

5. Use the <ENTER> key to select the option.

6. To exit, press <ESC>. To save and exit, press <F10>.

7. Section 3.2 to 3.7 will explain the option in more details.

AMIBIOS HIFLEX SETUP UTILITIES - VERSION 1.22

Reserved

Standard CMOS setup for changing time, hard disk type, etc.

CHAPTER 4 AMI

BIOS USERS GUIDE

4-4

2. Use <Up> and <Down> to choose the item and <PgUp> and

<PgDn> keys to modify the highlighted item.

3. After you have finished with the Standard CMOS Setup, press

<ESC> to go back to the main menu.

4.2 Standard CMOS Setup

1. Press <ENTER> on “Standard CMOS Setup” of the main menu

screen .

AMIBIOS SETUP - STANDARD CMOS SETUP

Date (mm/dd/yyyy): Fri March 20, 1999

Time (hh/mm/ss): 17:09:25

Floppy Drive A: 1.44 MB 3 1/2

Floppy Drive B: Not Installed

LBA Blk PIO 32Bit

Type Size Cyln Head WPcom Sec Mode Mode Mode Mode

Pri Master :Auto ON ON AUTO ON

Pri Slave :Auto ON ON AUTO ON

Sec Master :Auto ON ON AUTO ON

Sec Slave :Auto ON ON AUTO ON

Boot Sector Virus Protection Disabled

ESC:Exit :Sel

PgUp/PgDn:Modify

F2/F3:Color

Month : Jan-Dec

Day : 01-31

Year : 1901-2099

CHAPTER 4 AMI

BIOS USERS GUIDE

4-5

2. Use <Up> and <Down> to choose the item and <PgUp> and

<PgDn> keys to modify the highlighted item.

3. After you have finished with the Advanced CMOS Setup, press

<ESC> to go back to the main menu.

Quick Boot Enabled

Ist Boot Device Floppy

2nd Boot Device IDE 0

3rd Boot Device CD-ROM

Try Other Boot Devices Yes

Initial Display Mode BIOS

Display Mode at Add-On ROM Init Force-BIOS

Floppy Access Control Read-Write

S.M.A.R.T. For Hard Disk Disabled

BootUp Num-Lock On

Floppy Drive Swap Disabled

Floppy Drive Seek Disabled

PS/2 Mouse Support Enabled

Primary Display VGA/EGA

Password Check Setup

Boot to OS/2 > 64M No

CPU Serial Number Disabled

Cache Bus ECC Enabled

System BIOS Cacheable Disabled

C000, 64k Shadow Enabled

ESC:Exit :Sel

PgUp/PgDn:Modify

F2/F3:Color

4.3 Advanced CMOS Setup

1. Press <ENTER> on “Advanced CMOS Setup” of the main menu

AMIBIOS SETUP - ADVANCED CMOS SETUP

Available Options:

Disabled

Enabled

CHAPTER 4 AMI

BIOS USERS GUIDE

4-6

Descriptionoftheitemonscreenfollows:

Quick Boot

Set this option to Enabled to permit AMI®BIOS to boot within 5

seconds. This option replaces the old ABOVE 1 MB Memory Test option.

The Optimal default setting is Enabled. The Fail-Safe default setting is

Disabled.

1st Boot Device/2nd Boot Device/3rd Boot Device

This option sets the sequence of boot drives.

The settings are:

IDE0 The system will boot from the first HDD.

IDE1 The system will boot from the Second HDD.

IDE2 The system will boot from the Third HDD.

IDE3 The system will boot from the Fourth HDD.

F(optical) Thesystemwill boot from LS-120(120M Floppy).

SCSI The system will boot from the SCSI.

Network The system will boot from the Network drive.

CD-ROM Thesystem will boot from the CD-ROM.

Disable Disable this sequence.

Try other Boot Devices

This option sets the device boot, if all the Four Boot Devices failed.

Initial Display Mode

This option sets the device boot, if all the Four Boot Devices failed.

Display Mode at Add-On ROM Init

This option sets the device boot, if all the Four Boot Devices failed.

Floppy Access Control

This option sets the Floppy to Read-only or Read-Write.

S.M.A.R.T. for Hard Disks

This option sets the SMART Function for the hard disk. The hard

disk need to have SMART function for this feature to work.

CHAPTER 4 AMI

BIOS USERS GUIDE

4-7

Boot up Num Lock

When this option is set to Off, AMI®BIOS turns off the Num Lock

key when the system is powered on. The end user can then use the arrow

keys on both the numeric keypad and the keyboard. The settings are On or

Off. The optimal default and Fail-Safe default settings are On.

Floppy Drive Swap

Set this option to Enabled to specify that floppy drives A: and B: are

swapped. The setting are Enabled and Disabled. The Optimal and Fail-Safe

default settings are Disabled.

Floppy Drive Seek

When this option is set to Enabled, AMI®BIOS performs a Seek

command on floppy drive A: before booting the system. The settings are

Enabled and Disabled. The Optimal and Fail-Safe default settings are

Disabled.

PS/2®Mouse Support

When this option is set to Enabled, AMI®BIOS supports a PS/2®

mouse. The settings are Enabled and Disabled. The Optimal and Fail-Safe

default settings are Enabled.

PrimaryDisplay

This option configures the primary display subsytem in the computer.

ThesettingsareMono(monochrome),40CGA,80CGAorVGA/EGA. The

optimaland Fail-Safe default settings are VGA/EGA.

Password Check

This option specifies the type of AMI®BIOS password protection

that is implemented. The Optimal and Fail-Safe default settings are Setup.

Boot To OS/2® > 64MB

Set this option to Enabled to permit the BIOS to run properly, if OS/

2®is to be used with > 64MB of DRAM. The settings are Enabled or

Disabled. The Optimal and Fail-safe default settings are Disabled.

Tabla de contenidos

Otros manuales de Placa madre de MSI

MSI

MSI B360M BAZOOKA PLUS Manual de usuario

MSI

MSI IM-QM77 Manual de usuario

MSI

MSI MS-6382 Manual de usuario

MSI

MSI Pro266 Master Manual de usuario

MSI

MSI MPG B760I EDGE WIFI DDR4 Manual de usuario

MSI

MSI Z77MA-G43 Series Manual de usuario

MSI

MSI 990XA-GD55 series Manual de usuario

MSI

MSI 7C67-001R Manual de usuario

MSI

MSI Z75MA-G43 Series Manual de usuario

MSI

MSI Z87I Manual de usuario

MSI

MSI MS-7269 Manual de usuario

MSI

MSI MAG B660M BAZOOKA Manual de usuario

MSI

MSI PRO B660M-A WIFI DDR4 Manual de usuario

MSI

MSI MPG Z490M GAMING EDGE WIFI Manual de usuario

MSI

MSI Z97-G55 SLI Manual de usuario

MSI

MSI K9A2 Platinum series Manual de usuario

MSI

MSI MAG Z490 TOMAHAWK Manual de usuario

MSI

MSI Q57M-E40 Series Manual de usuario

MSI

MSI A320MPRO-VDH Manual de usuario

MSI

MSI G31TM-P21 - Motherboard - Micro ATX Manual de usuario

MSI

MSI K7N420 Pro Manual de usuario

MSI

MSI 890GXM Manual de usuario

MSI

MSI Z370I GAMING PRO CARBON AC Manual de usuario

MSI

MSI 865PE NEO2-LS - Motherboard - ATX Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario