MSI 694D Pro2 Manual de usuario
Introduction
1-1
Chapter 1.
Introduction
The 694D Pro2 (MS-6321 v2.X) ATX mainboard is a high- erformance
com uter mainboard based on VIA® Apollo Pro133A chi set. The 694D
Pro2 is designed for Intel® Pentium® III (FC-PGA) rocessor for cost-
effective business/ ersonal deskto and entry-level server markets.
The Apollo Pro133A consists of the VT82C694XDP North Bridge
and VT82C686B South Bridge. VT82C694XDP is a system controller su -
orting AGP 4X, 133MHz Front Side Bus and eight banks of PC100/PC133
SDRAMs. With 133MHz Front Side Bus, the north bridge o timizes the
erformance of Intel® Pentium III. The chi sets asynchronous bus design
is also ideal for CPU to run at FSB s eeds of 66 and 100MHz.
The VIA® VT82C686B Su er I/O PCI integrated Peri heral Controller
(PSIPC) includes PCI-to-ISA bridge controller, keyboard controller and USB
controller. In addition, it su orts dual bus-master IDE with Ultra DMA 33/
66/100, four USB orts, system hardware monitoring and enhanced ower
management ca abilities.
This cha ter includes the following to ics:
Mainboard S ecifications 1-2
Mainboard Layout 1-4
Quick Com onents Guide 1-5
Key Features 1-6
MSI S ecial Features 1-7
Chapter 1
1-2
CPU
!Su orts dual Intel® Pentium III (FC-PGA/FC-PGA2) rocessor
!Su orts 233MHz, 266MHz, 300MHz, 333MHz, 350MHz, 400MHz,
450MHz, 500MHZ, 533MHz, 667MHz, 700MHz, 733MHz, u to 1.13GHz
Chipset
!VIA® 694X chi set (510 BGA)
- P-III FSB @133MHz
- AGP 4X and PCI lus Advanced ECC Memory Controller
- Su orts PC100/133 SDRAM & VCM technology
!VIA® VT82C686B chi set (352 BGA)
- Advanced Power Management Features
- Dual bus Master IDE Ultra DMA 33/66/100
!1394 PHY Controller (o tional)
- TI® TSB41LV02 PHY Digital-to-Analog Transceiver
- Su ort u to Two 1394/1394A v 2.0 Com atible Data Channels
!1394 Link Layer Controller (o tional)
- TI® TSB12LV26 1394 Link Layer Host Controller
- IEEE 1394, 1394 OHCI v1.0 & 1394A v2.0 com atible
- Su orts 100/200/400 Mb s High Through ut
- 3.3V & 5V O eration for PCI-to-1394 Interface
Clock Generator
!66.6MHz, 100MHz and 133MHz clocks are su orted.
Main Memory
!Su orts eight memory banks using four 168- in unbuffered DIMM
!Su orts a maximum memory size of 2GB
- Pin outs su ort 8 banks u to 2GB DRAM (256MB DRAM
Technology) at 100MHz. However, it is recommended to install a limit of
3 DIMMS or 6 banks at 133MHz for 1.5GB maximum memory.
!Su orts ECC (1-bit Error Code Correct) function
!Su orts 3.3V SDRAM DIMM
Slots
!One AGP 4X (Accelerated Gra hics Port) slot
Mainboard Specification
Introduction
1-3
- AGP s ecification com liant
- AGP 66/133MHz 3.3V device su ort
!One CNR (Communication Network Riser) slot
!Five 32-bit Master PCI Bus slots
!Su orts 3.3V/5V PCI bus Interface
On-Board IDE
!An IDE controller on the VIA® VT82C686B chi set rovides IDE HDD/
CD-ROM with PIO, Bus Master and Ultra DMA 66/100 o eration modes.
!Can connect u to four IDE devices
Promise RAID Optional)
!Su orts RAID 0 or 1
!Can connect u to four IDE HDDs (ATA33/66/100)
On-Board Peripherals
!On-Board Peri herals include:
- 1 flo y ort su orts 2 FDDs with 360K, 720K, 1.2M, 1.44M and
2.88Mbytes.
- 2 serial orts (COM A + COM B)
- 1 arallel ort su orts SPP/EPP/ECP mode
- 4 USB orts (2 Rear Connectors/ 2 from USB Front Pin Header -- one of
the orts su orts USB PC to PC Networking function)
- 1 IrDA/HP connector for HPSIR
BIOS
!The mainboard BIOS rovides Plug & Play BIOS which detects the
eri heral devices and ex ansion cards of the board automatically.
!The mainboard rovides a Deskto Management Interface(DMI) function
which records your mainboard s ecifications.
Dimension
!ATX Form Factor: 25.4cm (W) x 30.4cm (L)
Mounting
!9 mounting holes
Chapter 1
1-4
Mainboard Layout
694D Pro2 MS-6321 v2.X) ATX Mainboard
AGP Slot
ATX
Power Supply
JFP1
JWOL1
BIOS
IDE 4 (ATA100-2)
IDE 3 (ATA100-1)
DIMM 4
DIMM 3
DIMM 2
CNR BATT
SYSFAN
USB
Ports
Top :
Parallel Port
Bottom:
COM A
COM B
Top : mouse
Bottom:
keyboard
IDE 1
IDE 2
FDD1
D LED
1394 Link
Layer
Controller
(Optional)
1394 PHY
Controller
(Optional)
CPU 1
CPU 2
USB2
JP1
J11
(Optional)
J12 (Optional)
JRMS1
JGS1
J6
J3
JMDM1
JBAT1
JGL1
VT82C
686B
81)
$'":,2
DIMM 1
CPUFAN1
CPUFAN2
Promise
20265R
(Option l)
SOCKET 370
SOCKET 370
PCI Slot 1
PCI Slot 3
PCI Slot 4
PCI Slot 2
PCI Slot 5
Introduction
1-5
Quick Components Guide
Component Function Reference
DIMM1~4 Installing SDRAM modules See p. 2-5~2-6
Socket 3 0 Installing CPU(s) See p. 2-2~2-3
CPUFAN1/2 Connecting to CPUFAN See p. 2-21
SYSFAN Connecting to SYSTEM FAN See p. 2-21
ATX Power Supply Installing power supply See p. 2-
IDE1& IDE2 Connecting to IDE hard disk drive See p.2-13
IDE3& IDE4 Connecting to IDE RAID HDD See p.2-14
FDD1 Connecting to floppy disk drive See p.2-12
USB2 Connecting to USB interface See p. 2-22~2-24
PCI Slot 1~5 Installing expansion cards See p. 2-29
AGP Slot Installing AGP cards See p. 2-29
CNR Slot Installing expansion cards See p. 2-29
JMDM1 Connecting to modem module See p. 2-19
JWOL1 Connecting to LAN card See p. 2-19
JBAT1 Clearing CMOS data See p. 2-28
JFP1 Connecting to case See p. 2-15
JGS1 Connecting to power saving switch See p. 2-18
JGL1 Connecting to power saving LED See p. 2-1
J3 Connecting to IR module See p. 2-20
JRMS1 Connecting to power switch See p. 2-18
J6 Connecting to HDD LED See p. 2-20
J11 & J12 Connecting to IEEE 1394 interface See p. 2-26~2-2
JP1 Connecting to D-Bracket See p. 2-25
Chapter 1
1-6
!ATX Form Factor
!CPU: Socket 370 for Single/Dual Intel® Pentium III
!Memory: 4 PC100/PC133 SDRAMs
!Slot: 1 AGP slot, 1 CNR slot, 5 PCI slots
!I/O: 2 serial orts, 1 arallel ort, 4 USB orts, 1 flo y ort, 1 IrDA
connector
!USB Interface: USB 1.1 PC to PC Networking
!Jum erless
!1394 Interface (o tional)
!2 IDE RAID connectors su orting RAID 0 or 1 (o tional)
!T.O.P Tech - Thermal Overheat Protection Technology
!PC Alert III system hardware monitor
!D-LED - 4 LEDs embedded in the mainboard
Key Features
Introduction
1-7
MSI Special Features
T.O.P Tech
The T.O.P TechTM is a extended sensing device that can 100% accu-
rately detect the CPUs teme rature. You can find out the tem erature on BIOS
setu menu. The PC AlertTM also rovides the information.
CPU temperaure on Setup menu
↑ ↓ → ←:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F :Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
Current CPU1 Temp. 40°C/104°F
Current CPU2 Temp. 30°C/86°F
Current CPUFAN1 Speed 4200Rpm
Current CPUFAN2 Speed 6124Rpm
CPU1 Vcore 1.64V
CPU2 Vcore 1.98V
3.3V 3.31V
V 4.9 V
12V 11.64V
CMOS Setup Utility - Copyright(C) 1984-2000 Award So tware
PC Health Status
Item Help
Menu Level !
Chapter 1
1-8
PC Alert III
The PC AlertTM III is an utility you can find in the CD-ROM disk. The
utility is just like your PC doctor that can detect the following PC hardware
status during real time o eration:
* monitor CPU & system tem eratures
* monitor fan s eed(s)
* monitor system voltage
* monitor chassis intrusion
If one of the items above is abnormal, the rogram main screen will be immedi-
ately shown on the screen, with the abnormal item highlighted in red. This will
continue to be shown,until user disables the warning.
Note: Items shown on PC Alert III vary depending on your systems status.
Introduction
1-9
Features:
!Network Management
- Monitoring & remote control
!Basic System Utilities
- Scandisk & Defragment to maintain your HDD
!3D Gra hics Design
- Enables a more friendly user interface
!Sofware Utilities
- SoftCooler O timized Cooling
Chapter 1
1-10
D-LED & D-Bracket
D-LED D-Bracket Description
System Power ON
- The D-LED will hang here i the processor is damaged or
not installed properly.
Early Chipset Initialization
Memory Detection Test
- Testing onboard memory size. The D-LED will hang i
the memory module is damaged or not installed properly.
Decompressing BIOS image to RAM or ast booting.
Initializing Keyboard Controller.
Testing VGA BIOS
- This will start writing VGA sign-on message to the screen.
Red Green
The D-LED uses gra hic signal dis lay to hel
users understand their system. Four LEDs embedded in
the mainboard rovide u to 16 combinations of signals to
debug the system. The 4 LEDs can debug all roblems that
fail the system, such as VGA, RAM or other failures. This
s ecial feature is very useful for the overclocking users.
These users can use the feature to detect if there are any
roblems or failures.
If your motherboard su orts and installs D-Bracket which also
integrates four Diagnostic LEDs, definitions of the LED signals are the same
as D-LED as shown below.
"
!
Diagnostic LED
!"
!"
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Placa madre de MSI
MSI
MSI MS-7250 Manual de usuario
MSI
MSI H67MA-E35 B3 series Manual de usuario
MSI
MSI H510TI-S09 Manual de usuario
MSI
MSI H170M ECO Manual de usuario
MSI
MSI 7D96-003R Manual de usuario
MSI
MSI Z170-A PRO Manual de usuario
MSI
MSI Eclipse Plus Series Manual de usuario
MSI
MSI MEG Z590 UNIFY-X Manual de usuario
MSI
MSI H310M GAMING ARCTIC Manual de usuario
MSI
MSI Midas 915GM Manual de usuario
MSI
MSI MEG Z490 GODLIKE Manual de usuario
MSI
MSI MS-7211 Manual de usuario
MSI
MSI Z270M MORTAR Manual de usuario
MSI
MSI H110M-A PRO M2 Manual de usuario
MSI
MSI MEG X570S UNIFY-X MAX Manual de usuario
MSI
MSI H61I-E35 (B3) Manual de usuario
MSI
MSI A88X-G45 GAMING Manual de usuario
MSI
MSI P67A-GD65 Series Manual de usuario
MSI
MSI H6M-P20 (G3) Manual de usuario
MSI
MSI Z97U GAMING 9 ACK Manual de usuario
Manuales populares de Placa madre de otras marcas
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manual de usuario
Gigabyte
Gigabyte GA-9IVDT Manual de usuario
Texas Instruments
Texas Instruments ADS8372EVM Manual de usuario
Commell
Commell MS-C73 Manual de usuario
IBT Technologies
IBT Technologies MB860 Manual de usuario
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manual de usuario
