MSA NightFighter Manual de usuario

ManualNightFighterInstallation.doc Prnt Spec. 10000005389(B) Mat. 10035581

07/23/02 Page 1of15

NightFighter™

INSTALLATION INSTRUCTIONS

BRACKET AND TRANSMITTER KIT

WARNING!

Read this manual carefully if you have or will have the responsibility for using or servicing

the product. The ClearCommand™ Communications System from MSA will perform as

designed only if used and serviced according to the instructions. Otherwise, the product

could fail to perform as designed, and persons who rely on this product could sustain

serious personal injury or death.

The warranties made by MSA with respect to the product are voided if the product is not used

according to the instructions in this manual. We encourage our customers to write or call for a

demonstration of this equipment prior to use, or for any additional information relative to use or

repairs. Call 1-800-MSA-2222 during regular working hours.

NIOSH and NFPA certified as an accessory for the Ultra Elite facepiece for use with the MSA

MMR, MMR with Slide Connection and BMR breathing apparatus only.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

conditions: (1) this device may not cause harmful interference, and (2) this device must accept

any interference that may cause undesired operation.

Changes or modifications not expressly approved by the manufacturer could void the user’s

authority to operate the equipment.

ManualNightFighterInstallation.doc Prnt Spec. 10000005389(B) Mat. 10035581

07/23/02 Page 2of15

DESCRIPTION / INSTALLATION

TABLE OF CONTENTS

DESCRIPTION....................................................................................................................2

PREPARING FOR USE......................................................................................................2

DESCRIPTION

1. The NightFighter Bracket and Transmitter Kit is designed to attach to an MSA Ultra Elite

facepiece to allow the easy attachment and removal of the NightFighter.

ULTRA-ELITE FACEPIECE

Removing the Component Housing Cover for MMR

1. Remove the two component housing cover screws and spacers. Remove the neckstrap.

2. Remove the locking ring.

3. Lift up on the cover release hook, located forward of the adapter assembly opening. Once the

release is lifted, you can remove the cover by pulling it away from the housing. You must tilt

the cover and work it over one adapter bayonet at a time.

Removing the Component Housing Cover for MMR with Slide Connection

1. Remove the two component housing cover screws. Remove the neckstrap.

2. Lift up on the cover. You can remove the cover by pulling it away from the housing. You

can tilt the cover and work it over adapter.

3. Unthread and remove the adapter assembly.

Removing the Component Housing cover for BMR

1. Unthread and remove the adapter assembly.

2. Remove the two component housing cover screws and the neckstrap.

3. Lift up on the cover release hook, located forward of the adapter assembly opening. Once

the release is lifted, you can remove the cover by pulling it away from the housing.

ManualNightFighterInstallation.doc Prnt Spec. 10000005389(B) Mat. 10035581

07/23/02 Page 3of15

CAUTION!

Be careful that you do not damage internal parts of the component housing assembly

(exhalation valve, spring, retainer, or speaking diaphragm) once the cover is removed.

Note: The following procedures are for MMR, MMR with Slide Connection and BMR

facepieces:

ManualNightFighterInstallation.doc Prnt Spec. 10000005389(B) Mat. 10035581

07/23/02 Page 4of15

INSTALLATION OF BRACKET

Install the Mounting Bracket to the Facepiece

1. Using a Phillips screwdriver, loosen and remove the screw from right side of the facepiece

lens retaining ring. (Be sure not to lose the nut if applicable).

2. Position the metal tab of the mounting bracket on top of the lens rings, and reinstall the

screw. Tighten firmly.

3. Using a small Phillips screwdriver, remove the component housing ring screw.

4. Position mounting bracket over component housing. Ensure the alignment of metal tab over

component housing insert and the alignment of mounting bracket screw hole over component

housing ring hole.

5. Insert longer screw (supplied with kit) through mounting bracket into component housing

ring hole. Tighten firmly.

Replace the Component Housing Cover for MMR, MMR with Slide Connection and BMR

Ultra Elite Facepiece.

CAUTION!

Be careful that you do not damage internal parts of the component housing assembly

(exhalation valve, spring, retainer, or speaking diaphragm) once the cover is removed.

Installing the Adapter Assembly for MMR

1. Holding the adapter assembly in your hand, rotate the slip nut so that the octagon flange on

the slip nut lines up with the octagon flange on the adapter.

2. Thread the adapter assembly into the facepiece. Using the spanner wrench, torque the

adapter to 12-27 in-lbs. If necessary, continue to torque until the top flat on the octagon is

horizontal.

3. The bayonets must be in a horizontal orientation.

4. If the bayonets are not horizontal, remove the adapter assembly and turn the slip nut.

Reinstall the adapter assembly so that the bayonets are horizontal when the adapter assembly

is torqued 12-27 in-lbs.

ManualNightFighterInstallation.doc Prnt Spec. 10000005389(B) Mat. 10035581

07/23/02 Page 5of15

Installing the Adapter Assembly for MMR with Slide Connection

1. Thread the adapter assembly into the facepiece. If necessary, use component housing cover

to continue to tighten until the top flat on the octagon is horizontal.

Installing the Component Housing Cover for MMR

1. Place the component housing cover over the adapter assembly. Tilt and rotate the cover to

work it over one bayonet at a time.

2. Insert the tab on the cover into the slot in the lens ring.

3. Press in on the front of the cover until the cover hook snaps into place.

4. Install the locking ring by sliding it into the groove on the adapter. (Do not slide it into the

space between the slip nut flange and the adapter flange.)

5. Place the spacers and the neckstrap brackets in the cover sockets under the locking ring.

Install the Phillips screws through the bracket, spacer, cover and metal top of bracket and

tighten.

6. Verify each of the following features:

a. The adapter bayonets are locked into a horizontal position and can NOT be rotated.

b. The slip nut is threaded completely into the facepiece and locked securely. It can NOT

be rotated.

c. The metal locking ring is locked into position and can NOT be rotated.

d. There is no loose play in the assembly of parts.

7. Don the facepiece and check the face-to-facepiece seal. Follow the Facepiece Fit Check

procedures in the MMR Operations and Instructions Manual.

Installing the Component Housing Cover for MMR with Slide Connection

1. Place the component housing cover over the adapter assembly.

2. Insert the tab on the cover into the slot in the lens ring. Press in on the front of the cover until

the cover hook snaps into place.

3. Line up the screw holes in the cover with the metal tab of mounting bracket and threaded

inserts in the housing.

4. Place the neckstrap brackets into the cover sockets. Install the new Phillips screws and

tighten.

ManualNightFighterInstallation.doc Prnt Spec. 10000005389(B) Mat. 10035581

07/23/02 Page 6of15

5. Verify that there is no loose play in the assembly of parts.

6. Don the facepiece and check the face-to-facepiece seal. Follow the Facepiece Fit Check

procedures in the MMR with Slide Connection Operation and Instructions Manual.

Installing the Component Housing Cover Adapter Assembly for BMR

1. Place the component housing cover over the housing.

2. Insert the tab on the top of the cover into the slot in the bottom of the lens ring.

3. Press in on the front of the cover until the cover hook snaps into place.

4. Line up the screw holes in the cover with the metal tab of mounting bracket and threaded

inserts in the housing.

5. Place the neckstrap retaining brackets in the component housing cover sockets. Install the

Phillips screws and tighten to secure the housing and neckstrap.

6. Insert the adapter assembly in the facepiece and hand-tighten.

7. Don the facepiece and check the face-to-facepiece seal. Follow the Facepiece Fit Check

procedures in the BMR Operations and Instructions Manual.

ManualNightFighterInstallation.doc Prnt Spec. 10000005389(B) Mat. 10035581

07/23/02 Page 7of15

INSTALLATION FOR MMR TRANSMITTER

INTRODUCTION

This kit supplies the parts necessary to add the NightFighter Transmitter to the following SCBA:

•MMR without a Quick-Fill Option

•MMR with an old-style (pipe thread) Quick-Fill Option installed

•MMR with a Redundant Alarm installed

•MMR with an ICM 2000/2000 Plus installed

You must be a Certified Repairperson to perform the installation procedures which follow.

COMMON PARTS

•638166 O-ring

•635277 Backup ring (3)

•10003605 Spool

REQUIRED TOOLS

The tools contained in the Tool Kit supplied to Certified Repairpersons will be sufficient to

install this kit.

WARNING!

Before starting the procedures below, be sure that the cylinder valve is completely closed.

Be sure that nothing blocks the regulator outlet. Open the bypass valve to relieve any

pressure in the system. Failure to follow this precaution can cause serious personal injury

or death.

ManualNightFighterInstallation.doc Prnt Spec. 10000005389(B) Mat. 10035581

07/23/02 Page 8of15

PREPARING AN MMR WITH NO QUICK-FILL OPTION INSTALLED

Note: If your SCBA does not have the Quick-Fill Option installed on the over-the-shoulder

gauge line hose, you must remove the gauge from the MMR harness gauge hose.

1. Close the bypass valve fully.

WARNING!

Do not disconnect the alarm coupling nut when pressure is shown on the harness gauge.

Always be sure that you have released all pressure from the regulator. Removing the

coupling nut with the regulator pressurized may result in serious personal injury or death.

2. Unscrew the alarm coupling nut from the cylinder valve.

ManualNightFighterInstallation.doc Prnt Spec. 10000005389(B) Mat. 10035581

07/23/02 Page 9of15

INSTALLATION FOR MMR

Removing the Gauge Adapter and Pressure Gauge

1. Using wrenches, unthread and remove the gauge adapter and the pressure gauge from the

hose fitting.

2. Using the O-ring removal tool, remove the O-ring and backup ring from the end of the hose

fitting. Discard the old O-ring and backup ring.

3. Go to Installing the Transmitter in the Adapter Block (below).

PREPARING AN MMR WITH AN OLD-STYLE (PIPE THREAD) QUICK-FILL

OPTION INSTALLED

1. Using wrenches, unthread and remove the existing Quick-Fill block and pressure gauge from

the gauge hose fitting.

2. Using the O-ring removal tool, remove the O-ring and backup ring from the end of the gauge

hose fitting.

Note: You can salvage the Quick-Fill Coupling from the exiting block.

3. Place the Adapter block in a vise. Use protective sleeves to keep from damaging the block.

Unthread the coupling from the block using a 1" deep-well socket. Set the adapter block

aside.

4. Remove and discard the existing O-ring (P/N 635068) from the Quick-Fill coupling (P/N

485070). Use a plastic pick, a tooth pick or a bull nose dental pick.

PREPARING AN MMR WITH A REDUNDANT ALARM OR ICM INSTALLED

1. Using the 5/8" wrenches, loosen and remove the pressure gauge and redundant alarm from

the pressure gauge hose. Set the gauge and alarm aside.

2. Using the O-ring removal tool, remove the O-ring and backup ring from the end of the hose.

3. Continue below.

ManualNightFighterInstallation.doc Prnt Spec. 10000005389(B) Mat. 10035581

07/23/02 Page 10 of 15

INSTALLING THE COUPLING IN THE TRANSMITTER ADAPTER BLOCK

1. Place the Adapter block in a vise. Use protective sleeves to keep from damaging the block.

2. Insert the filter into the base of the block.

3. Wrap the coupling threads with transparent tape to prevent damage to the O-ring. Apply a

thin film of Christo-Lube to the P/N 635068 coupling O-ring. Slide the new O-ring over the

coupling threads. Remove the tape.

4. Thread the coupling into the block and tighten to 70-75 ft.-lbs. using a 1" deep-well socket.

INSTALLING THE TRANSMITTER ON THE GAUGE LINE

1. Apply a thin film of Christo-Lube to a newbackup ring. Place the backup ring in the groove

on the end of the hose fitting.

2. Apply a thin film of Christo-Lube lubricant to a newO-ring. Place the O-ring in the groove

on the end of the hose fitting.

3. Insert the hose fitting into the Transmitter Adapter Block. Torque the adapter to 50-60 in.-

lbs.

Note: If your apparatus is equipped with the Redundant Alarm or ICM, its pressure gauge will

have the Spool included. Make sure that the spool stays with the gauge.

•Check that the spool is present in the gauge (Redundant Alarm or ICM) outlet.

Note: If the spool is not installed, you must first install an O-ring and backup ring on each end,

•Apply a thin film of Christo-Lube lubricant to two P/N 635277 backup rings. Place one

backup ring in the groove on each end of the spool.

•Apply a thin film of Christo-Lube lubricant to two P/N 638167 O-rings. Place one O-ring in

the groove on each end of the spool.

Tabla de contenidos

Otros manuales de Equipo de seguridad de MSA

MSA

MSA Gallet F2XR Manual de usuario

MSA

MSA OptimAir 3000 Manual de usuario

MSA

MSA PremAire System Manual de usuario

MSA

MSA 10110162 Instrucciones de operación

MSA

MSA V-FLEX Harnesses Manual de usuario

MSA

MSA 415865 Manual de usuario

MSA

MSA FieldServer FS-QS-1 Series Guía del usuario

MSA

MSA fieldserver FS-8700-144 Nota de publicación

MSA

MSA Grid RESTful API Guía del usuario

MSA

MSA Cairns XR2 Manual de usuario

MSA

MSA left/RIGHT Manual de usuario

MSA

MSA HUB Manual de usuario

MSA

MSA PremAire Cadet Escape Respirator Guía de configuración

MSA

MSA BD mini Manual de usuario

MSA

MSA AirMaXX classic Manual de usuario

MSA

MSA AUER 3S-PS Manual de usuario

MSA

MSA OptimAir Mask-Mounted PAPR Manual de usuario

MSA

MSA SCBA Basic Apparatus AirGo Manual de usuario

MSA

MSA left/RIGHT Manual de usuario

MSA

MSA PremAire Cadet Escape Manual de usuario

MSA

MSA AirFrame 10046846 Guía de configuración

MSA

MSA ULTIMA X5000 Guía del usuario

MSA

MSA HUB Manual de usuario

MSA

MSA Sure-Climb SFPLS350 Series Manual de usuario

Manuales populares de Equipo de seguridad de otras marcas

Innova

Innova Xtirpa Manual de instrucciones

bolle SAFETY

bolle SAFETY B810 Manual de usuario

SHENZHEN FANHAI SANJIANG ELECTRONICS

SHENZHEN FANHAI SANJIANG ELECTRONICS A9060T Manual de usuario

Hiltron security

Hiltron security POWER8E Guía

Hatco

Hatco B-950P Manual de usuario

Sitec

Sitec TX MATIC Manual de usuario

TEUFELBERGER

TEUFELBERGER GRIP 12 Manual de usuario

AMC

AMC 1022M Series Manual de usuario

Trinity

Trinity CASS S3 Manual de usuario

CMC

CMC Helitack HotSeat Manual de usuario

Force

Force P-35 Manual de usuario

ACM

ACM SAFETY D200 Manual del producto

Honeywell

Honeywell Miller H-Design DuraFlex Manual del operador

ROCK

ROCK P-451 AS Manual de usuario

Power first

Power first 2XYR7A Manual de servicio

SCHUBERTH

SCHUBERTH SHP 28-C Manual de usuario

Trango

Trango CINCH Manual de usuario

Escape

Escape Escape Chair VOLT Manual de usuario