MSA Left/RIGHT Manual de usuario

MSAsafety.com

Operating Manual

left/RIGHT

Hearing Protection

Order No.: PM259/00

CE Certificate Holder

MSA Europe GmbH

Schlüsselstrasse 12

8645 Rapperswil-Jona

Switzerland

info.ch@MSAsafety.com

www.MSAsafety.com

Manufacturer

MSA Sordin AB

Rörläggarvägen 8

SE-331 53 Värnamo

Sweden

Fig. 1 Fig. 2 Fig. 3 Fig. 4

Fig. 5 Fig. 6 Fig. 7 Fig. 8

Fig.9 Fig.10 Fig.11 Fig.12

CLIC CLIC

left/RIGHT 3

Product

1Product

The MSA left/RIGHT series consists of a range of ear-muffs with a level-dependent facility designed to

improve safety and working conditions in noisy environments. It consists of the following versions:

This manual is applicable for all versions. If a function is only available for certain versions, it is mentioned.

left/RIGHT Wireless World and left/RIGHT Wireless World Dual provide an entertainment audio facility. For

optimum comfort, fit and function of the product, it is important to read the instructions carefully and save

them for future reference.

WARNING!

To ensure proper hearing protection, the ear-muffs must be fitted, adjusted and maintained in accor-

dance with MSA‘s instructions. If these instructions are not adhered to, the protection afforded by the

ear muffs could be severly impaired.

Do not disassemble the ear-muffs. If any unauthorized repair or modification has been carried out on

the device, warranty is no longer valid.

left/RIGHT Wireless World and left/RIGHT Wireless World Dual have an entertainment audio facility.

The audibility of warning signals at a specific workplace may be impaired while using the entertainment

facility. These versions limit the entertainment audio signal to 82 dB(A) effective at the ear.

Remember that hearing protectors may shut out external ambient sounds, such as warning shouts,

alarms and other important signals. The audibility of warning signals at a specific workplace may be

impaired while using the entertainment facility. The user must be especially attentive of the surround-

ings when wearing hearing protection.

Depending on the model, this ear-muff is provided with level-dependant attenuation and/or electrical

audio output. The wearer should check correct operation before use. If distortion or failure is detected,

the wearer should refer to the manufacturers advice for maintenance and replacement of the battery.

Performance may deteriorate with battery usage. The battery life time varies depending on the mode

of use and volume output. The typical period of continuous use that can be expected from the ear-muff

battery is:

- Surround and Bluetooth active: approximately 30 h

- Surround only and Bluetooth inactive: approximately 350 h

The output of the level-dependent circuit of this hearing protector may exceed the external sound level.

The output of the electrical audio circuit of this hearing protector may exceed the daily limit sound level.

Refer to the attenuation table for further details on noise reduction. Make sure to select the correct product

for the application.

These models of ear-muffs have satisfied the optional requirements of thermal resistance at -20 °C and

+50 °C.

For details on how to operate the product and for a description of all functions of models

left/RIGHT Wireless World and left/RIGHT Wireless World Dual see additional manual PM260.

Product name

All products are available with

headband or as a helmet

mounted version

Bluetooth

wireless

technology

Ambient sound

FM radio

Aux entry

Color

Weight (in g)

excluding

batteries

left/RIGHT Wireless World X X

Black

Headband: 378g

Helmet mounted:

395g

left/RIGHT Wireless World Dual X X X X

Approvals

2 Approvals

2.1 Europe

The product meets the Basic Safety Requirements of the European Community Directive and the require-

ments of the EMC directive. Certificate issue by Emitech, 3, rue des Coudriers - CAP 78 - ZA de l’Obser-

vatoire - 78180 MONTIGNY LE BX - France

Attenuation Data

The attenuation values and noise levels for the headset are tested and approved according to EN 352-1,

EN 352-3, EN 352-4, EN 352-6, EN 352-8. Certificate issue by Finnish Institute of Occupational Health

(FIOH), Topeliuksenkatu 41aA, FIN-00250 Helsinki, Finland

The sound attenuation values of the hearing protectors are measured in accordance with EN 24869-1 (with

electronics off).

Key:

Criterion Levels

The sound pressure level of external sound for which the sound pressure level under the ear-muff first

exceeds 82 dB(A).

EN 300 328

EN 301 489-17

EN 301 489-3

EN 301 489-1

left/RIGHT Wireless World left/RIGHT Wireless World Dual

EN 352-1 X X

EN 352-3 X X

EN 352-4 X

EN 352-6 X X

EN 352-8 X X

f Frequencies at which attenuation is measured (Hz)

Mf Mean value (dB)

sf Standard deviation (dB)

APV (Mf-sf) Assumed Protection Value

HHigh frequency attenuation value (predicted noise level reduction for noise where

LC–LA –2 dB)

MMedium frequency attenuation value (predicted noise level reduction for noise where

LC–LA +2 dB)

LLow frequency attenuation value (predicted noise level reduction for noise where

LC–LA +10 dB)

SNR

Single Number Rating (the value that is subtracted from the measured C-weighted

sound pressure level, LC, in order to estimate the effective A-weighted sound level

inside the ear)

left/RIGHT 5

Materials

Headband version

H = 31 dB, M = 25 dB, L = 17 dB, SNR = 28 dB, NRR = 25 dB

Helmet mounted version

H = 29 dB, M = 23 dB, L = 16 dB, SNR = 26 dB, NRR = 24 dB

2.2 North America

The product meets with requirements of FCC 47 CFR PART 15

Certificate issue by Emitech, 3, rue des Coudriers - CAP 78 - ZA de l’Observatoire - 78180 MONTIGNY LE

BX - France

Attenuation Data

Attenuation measurements have been performed according to the American National Standards Institute

(ANSI) specifications, ANSI S3.19-1974. Certificate issue by Michael & Associates

NRR (Noise Reduction Rating) = Headband: 25dB, Helmet mounted: 24dB

3 Materials

f (Hz) 63 125 250 500 1000 2000 3150 4000 6300 8000

Mf (dB) 13.9 13.7 18.1 27.1 34.0 32.1 38.4 40.1 41.8 38.1

Sf(dB)5.13.22.03.34.14.24.84.43.53.5

APV (dB) 8.8 10.5 16.2 23.8 29.9 27.9 33.6 35.7 38.3 34.6

f (Hz) 63 125 250 500 1000 2000 3150 4000 6300 8000

Mf (dB) 12.7 13.7 16.2 24.3 31.2 32.2 33.0 36.4 35.5 31.6

Sf(dB)3.54.02.93.14.55.22.93.02.94.4

APV (dB) 9.2 9.7 13.4 21.2 26.7 27.0 30.1 33.4 32.6 27.2

left/RIGHT Wireless World left/RIGHT Wireless World Dual

ANSI S3.19-1974 X X

Part Materials Part Materials

Cup ABS Microphone arm Polyamide

Cover ABS Height adjustment bushings TPE

Headband Acetal Spring cover TPE

Headband fork Polyamide Bluetooth button TPE

Helmet fork,

Helmet attachment Polyamide Attenuation foam (inserts) Polyurethane

Spring bracket Polyamide Cushions Polyurethane, PVC

Fitting

4Fitting

The cushions should snugly fit the head with no interference of the seal by any objects e.g. respirator head-

bands or spectacle arms, the cups should completely enclose the ears. Before putting on the device, brush

excess hair aside and remove any jewellery that could affect acoustic seal.

Headband version

(1) Ensure that the headband is positioned correctly before putting it on.

The inside of the headband is marked with a letter L on the left hand side and a letter R on the

right hand side.

(2) With the headband over the head, adjust the height of the cups by sliding them up or down so they

completely enclose the ears (see Fig. 1).

Helmet version

These ear-muffs should be fitted to, and used only with, the following industrial safety helmets:

3 sets of adapters are provided with the device. Before the ear muffs can be attached to the helmet, the

adapters have to be installed.

(1) Attach the correct adapter (see Fig. 11) to the helmet (see table above).

(2) Ensure that the cups are mounted on the correct side of the helmet. The cup marked with L must be

put on the left hand side of the helmet and the cup marked with R must be put on the right hand side

of the helmet.

(3) Pull the ear cup down the fork as far as possible.

(4) Push the attachment clip firmly into the slot on the side of the helmet until it clicks into place

(see Fig. 2).

(5) Detach the head harness at two places at the rear of the helmet (see Fig. 3) and place the cord from

the cups above the harness attachment.

(6) Reattach the harness.

Ensure the cord is not tangled.

(7) For the working position, press the cups toward the ears until they click into place. Adjust the height

of the cups by sliding them up or down so they completely enclose the ears (see Fig. 4).

The grommet of the cable and the antenna is positioned inside the fork (see Fig. 12).

(8) Stand-by position: Pull the cups away from the ears until they lock into the stand-by position

(see Fig. 5).

(9) Parking Position: From the stand-by position, move the cups to the rear of the helmet until they click

into place. In this position, the cushions do not get damaged or dirty and the cups can dry

(see Fig. 6).

Helmet Brand / Model Adaptor Type No Approved sizes

MSA V-Gard 60614 S, M, L

MSA V-Gard 200 60601 S, M, L

MSA V-Gard 200 60614 M, L

MSA V-Gard 500 60614 S, M, L

MSA V-Gard 900t 60614 M, L

Balance AC 60601 S, M, L

Peltor G2000 60601 S, M, L

Peltor G3000 60602 S, M, L

Balance HD 60601 S, M, L

Protector Style 600 60602 S, M, L

Protector Style 300 60601 S, M, L

Auboueix Iris II 60601 and 60602 S, M, L

left/RIGHT 7

Ear Muffs

NOTE: Do not press the cups onto the helmet shell as this will lock the spring in the ear-muff arm, and

damage the attachment slots on the side of the helmet.

(10) Storage Position: When the helmet is not in use, lower the ear-muffs and push them inwards until

they click into place (see Fig. 7).

WARNING!

In noisy environments, the ear-muffs must be worn in the working position at all times.

The fitting of hygiene covers to the cushions may affect the acoustic performance of the ear-muffs.

5 Ear Muffs

Sizes

All ear-muffs of this series are ‘Medium size range’ ear-muffs and will fit the majority of wearers.

6Storage

When the ear-muffs are not in use, store them without stretching the headband and without compressing

the cushions. Keep the ear-muffs dry and clean, store them at normal room temperature and do not place

them in direct sunlight.

If the product is to be stored for a prolonged period, remove the batteries to avoid damage.

7 Maintenance

Inspect the ear-muffs regularly for serviceability. Ear-muffs, and in particular cushions, may deteriorate with

use and should be examined at frequent intervals for cracking and leakage, for example at the start of every

work shift. Clean and disinfect the cups, cushions and inserts with mild soap and water only. The ear-muffs

must not be immersed in water. This product may be adversely affected by certain chemical substances.

Further information should be sought from the manufacturer. Do not subject the product to rough handling,

which can damage the electronics.

Dispose of the product and batteries in accordance with national and local regulations.

7.1 Hygiene Kit

The cushions and inserts are replaceable. Always replace worn or damaged parts. Remove the cushion by

pulling it straight out (see Fig. 8). Replace the old cushion and insert with new ones from the hygiene kit

(see Fig. 9). Use only hygiene kits from MSA.

7.2 Batteries

Only use batteries with 1,5 rated voltage (rechargeable or non-rechargeable). The use of rechargeable

batteries such as NiMH 1.2 V or NiCd 1.2 V will significantly reduce operating time.

Replacing the Batteries

Turn the device off during battery replacement.

The battery compartment is located in the left cup (see Fig. 10). To install new batteries, remove the lid and

insert the batteries, starting with the upper battery. Make sure that the + and – poles are correctly aligned.

Replace the lid.

Microphone characteristics

Electret noise cancelling microphone

Waterproof IP67

Frequency range: 100 Hz-10 kHz

Type Product Number

Hygiene kit consisting of one pair of cushions, distance rings and inserts

Replace at least twice a year to ensure consistent attenuation, hygiene and comfort! 10094605

For local MSA contacts, please visit us at MSAsafety.com

Because every life has a purpose...

Otros manuales para left/RIGHT

Tabla de contenidos

Otros manuales de Equipo de seguridad de MSA

MSA

MSA G1 SCBA Manual de usuario

MSA

MSA AUER 3S-Basis Plus Manual de usuario

MSA

MSA OptimAir Mask-Mounted PAPR Manual de usuario

MSA

MSA PremAire System Manual de usuario

MSA

MSA V-FLEX Harnesses Manual de usuario

MSA

MSA Ultima X Series Guía del usuario

MSA

MSA OptimAir 3000 Manual de usuario

MSA

MSA Workman SRL-R Manual de usuario

MSA

MSA ExtendAire II Manual de usuario

MSA

MSA Dyna-Lock 506208 Manual de usuario

MSA

MSA ULTIMA X5000 Guía del usuario

MSA

MSA alphaBELT Pro Manual de usuario

MSA

MSA Gallet F2XR Manual de usuario

MSA

MSA SURETYMAN SRS15 Instrucciones de instalación

MSA

MSA V-FLEX Instrucciones de operación

MSA

MSA Cairns XR2 Manual de usuario

MSA

MSA Sure-Climb SFPLS350 Series Manual de usuario

MSA

MSA PremAire System Manual de usuario

MSA

MSA Grid RESTful API Guía del usuario

MSA

MSA G1 SCBA Manual de usuario

MSA

MSA ProtoAir FPA-W44 Manual de usuario

MSA

MSA AirMaXX SL Series Manual de usuario

MSA

MSA 10207284 Manual de usuario

MSA

MSA Rail Slider SFPRS6000 Manual de usuario

Manuales populares de Equipo de seguridad de otras marcas

Innova

Innova Xtirpa Manual de instrucciones

bolle SAFETY

bolle SAFETY B810 Manual de usuario

SHENZHEN FANHAI SANJIANG ELECTRONICS

SHENZHEN FANHAI SANJIANG ELECTRONICS A9060T Manual de usuario

Hiltron security

Hiltron security POWER8E Guía

Hatco

Hatco B-950P Manual de usuario

Sitec

Sitec TX MATIC Manual de usuario

TEUFELBERGER

TEUFELBERGER GRIP 12 Manual de usuario

AMC

AMC 1022M Series Manual de usuario

Trinity

Trinity CASS S3 Manual de usuario

CMC

CMC Helitack HotSeat Manual de usuario

Force

Force P-35 Manual de usuario

ACM

ACM SAFETY D200 Manual del producto

Honeywell

Honeywell Miller H-Design DuraFlex Manual del operador

ROCK

ROCK P-451 AS Manual de usuario

Power first

Power first 2XYR7A Manual de servicio

SCHUBERTH

SCHUBERTH SHP 28-C Manual de usuario

Trango

Trango CINCH Manual de usuario

Escape

Escape Escape Chair VOLT Manual de usuario

MSA left/RIGHT Manual de usuario

Manuales populares de Equipo de seguridad de otras marcas