MS Schippers MS Pigsleeper Flexy Manual de usuario

Assembly instructions MS Pigsleeper

Flexy

Introduction

This document describes how to correctly assemble the Pigsleeper Flexy. Everything

is explained with pictures.

Content

Introduction............................................................................................................................................. 2

Mounting the crossbar............................................................................................................................ 4

Mounting the upper section.................................................................................................................. 10

Mounting the Cup holder and bucket holder (OPTIONAL) ................................................................... 12

Mounting the cup holder on top........................................................................................................... 15

Installing the anaesthesia unit .............................................................................................................. 16

Isoflurane filter holder .......................................................................................................................... 17

Installing the compressor...................................................................................................................... 18

USB flash drive....................................................................................................................................... 19

Purple bottle top ................................................................................................................................... 19

Required tools

Ring/socket wrench 10 + 13

Allen key for M5, M6 and M8

Mounting the crossbar

1. Take the crossbar (traverse) and remove the foil.

2. The crossbar is delivered with all necessary nuts and bolts.

Now remove the side plate, which is attached with nuts and bolts (see drawing

and picture).

You will need a size 13 wrench and a M8 Allen key.

3. Loosen the two Allen screws on the other side of the crossbar slightly so that

they are flush with the plate.

4. Now remove the support mounted on top of the crossbar. This can be done

manually, as it is equipped with a rotary knob.

5. Place the crossbar on the middle beam of the trolley frame.

6. Then slide the side plate that you removed in step 2 back onto the frame.

Push it between the bar of the frame and the side of the crossbar.

Tip: First place the lock nut on the inside of the metal plate. Then screw the

M8 bolt in from the outside and fasten it.

7. Now that the crossbar is in place, it can be tightened on both sides at the

bottom with all 4 Allen screws.

Tighten the screws until the crossbar is firmly clamped to the frame.

See image at point 8 for a complete set-up.

8. Now take the 2 green boxes and the 2 toolboxes. Place them into the frame as

shown below.

9. Now insert the support back into the holder and tighten it to the desired

working height. The rotary knob is located on the rear.

Mounting the cable drum

10.The cable drum is mounted with the provided holder as follows.

Take the bracket and remove the bolts and nuts with a size 10 wrench and a

M5 Allen key.

11.The support can be mounted in 2 ways. Mount it according to the working

height. The 2 ways are shown below.

Caution! Do not tighten the screws yet. On the next page you’ll see the

complete set-up.

Option 1: High Option 2: Low

12.Make sure that the screw heads protrude, not the nuts. Then hook the black

bracket of the cable drum onto the two support bolts.

13.Then tighten the support bolts and nuts so that the cable drum is firmly

attached. The assembled frame now looks like this:

a. There are 2 variants of the power strip. The image shows a black one,

but it may also be that a red variant is supplied. Quality remains the

same

Mounting the upper section

14.Now remove the 4 bolts and the 2 black buttons from the crossbar. You will

need a M8 Allen key.

15.Then place the upper part on the crossbar as follows.

Tabla de contenidos

Otros manuales de Maquinaria agrícola de MS Schippers

MS Schippers

MS Schippers Greenline Move Guía de referencia

MS Schippers

MS Schippers MS Pulse 50 Manual de usuario

MS Schippers

MS Schippers MS AutoHoofClean Manual de usuario

MS Schippers

MS Schippers MS Tornades Series Manual de usuario

MS Schippers

MS Schippers Blitz-Kerner 3409900 Manual de usuario

MS Schippers

MS Schippers Automix 2.0 Guía rápida

MS Schippers

MS Schippers MS Automix 40 Manual de usuario

Manuales populares de Maquinaria agrícola de otras marcas

GSi

GSi PNEG-2314 Manual de usuario

Checchi & Magli

Checchi & Magli TEXDRIVE Manual de usuario

Amazone

Amazone Cenius 4003-2TX Manual de usuario

MASSEY FERGUSON

MASSEY FERGUSON MF 9313S Manual de usuario

Cima

Cima BLITZ Instrucciones de funcionamiento y mantenimiento

Amazone

Amazone CombiDisc 3000 Instrucciones de instalación

HE-VA

HE-VA Disc-Roller XL Contour Manual de usuario

AGT

AGT AGT-SSFM Manual de usuario

Milestone

Milestone 72-84 Manual de usuario

KUHN

KUHN Hector 3000 Manual de usuario

Krone

Krone X-Disc 6200 Manual de usuario

Eliet

Eliet DZC450 Manual de usuario

Taarup

Taarup BIO+ B4000 Manual de usuario

Garland

Garland SHAKER 310 DPG Manual de usuario

stable comfort

stable comfort StableWall System Manual de usuario

Raven

Raven AccuBoom Manual de usuario

International

International 710 Manual de usuario

Ashland

Ashland HDW-3217-14 Manual de usuario