Moxa Technologies NPort IA5150 series Manual de usuario

P/N: 1802051500217

*1802051500217*

NPort IA5150/5250 Series

Quick Installation Guide

Version 7.0, September 2021

Technical Support Contact Information

www.moxa.com/support

- 2 -

Overview

NPort IA device servers deliver easy and reliable serial-to-Ethernet

connectivity for the industrial automation market. The servers support

several operation modes—TCP Server, TCP Client, UDP, Real COM, Pair

Connection, and Ethernet Modem—ensuring the compatibility of

network software, and they are an ideal choice for connecting RS-

232/422/485 serial devices, such as PLCs, sensors, meters, motors,

drives, barcode readers, and operator displays. NPort IA device servers

come with a compact and rugged DIN-rail mountable casing.

NOTE

This equipment is intended for use in a restricted area location.

Package Checklist

Before installing NPort IA device servers, verify that the package

contains the following items:

•1 NPort IA Series device server

•Quick installation guide (printed)

•Warranty card

Optional Accessories

•DK-35A: DIN-rail mounting kit (35 mm)

•Mini DB9F-to-TB Adaptor: DB9 female to terminal block adapter

•DR-4524: 5W/2A DIN-rail 24 VDC power supply with universal 85

to 264 VAC input

•DR-75-24: 75W/3.2A DIN-rail 24 VDC power supply with universal

85 to 264 VAC input

•DR-120-24: 120W/5A DIN-rail 24 VDC power supply with 88 to

132 VAC/176 to 264 VAC input by switch

Note: Notify your sales representative if any of the above items are

missing or damaged.

NPort IA5150 Series Appearance

- 3 -

NPort IA5250 Appearance

Reset Button—Pr ess the Reset button for 5 seconds to load factory

defaults. Use a pointed object, such as a straightened paper clip or

toothpick, to press the reset button. This will cause the Ready LED to

blink on and off. The factory defaults will be loaded once the Ready LED

stops blinking (after about 5 seconds). At this point, you should release

the reset button.

NPort IA LED Indicators (front panel)

Name

Color

Function

PWR1, PWR2 Red

Power is being supplied to power input PWR1,

PWR2.

RDY

Red

Steady on: Power is on and the NPort IA is

booting up.

Blinking: Indicates an IP conflict, the DHCP or

BOOTP server did not respond properly, or a

relay output occurred.

Green

Steady on: Power is on, and the NPort IA is

functioning normally.

Blinking: The device server has been located

by the Administrator’s Location function.

Off

Power is off, or a power-error condition

exists.

Ethernet

Amber

10 Mbps Ethernet connection.

Green

100 Mbps Ethernet connection.

Off

Ethernet cable is disconnected or has a short.

P1, P2

Amber

Serial port is receiving data.

Green

Serial port is transmitting data.

Off No data is being transmitted or received

through the serial po rt .

FX Amber

Steady on: Ethernet fiber connection, but

port is idle.

Blinking: Fiber port is transmitting or

receiving data.

- 4 -

Hardware Installation Procedure

STEP 1: Connect the NPort IA to a network. Use a standard straight-

through Ethernet cable to connect to a hub or switch. When setting up

or testing the NPort IA, you might find it convenient to connect directly

to your computer’s Ethernet port. In this case, use a crossover Ethernet

cable.

STEP 2: Connect the NPort IA’s serial port to a serial device.

STEP 3: The NPort IA is designed to be attached to a DIN rail or

mounted on a wall. The two sliders on the NPort IA’s rear panel serve a

dual purpose. For wall mounting, both sliders should be extended. For

DIN-rail mounting, start with one slider pushed in, and the other slider

extended. After attaching the NPort IA on the DIN rail, push the

extended slider in to lock the device server to the rail. The two

placement options are illustrated in the accompanying figures.

STEP 4: Connect the 12 to 48 VDC power line with the NPort IA’s

terminal block or connect the DIN-rail power supply with the NPort IA’s

terminal block.

Power Input and Relay Output Pinouts

V2+ V2-

V1+ V1-

Shielded

Ground

DC Power

Input 1

Power

Input 1

Relay

Output

Relay

Output

Power

Input 2

Power

Input 2

Wallmount

DIN Rail

Wall or Cabinet Mounting

Mounting the NPort IA5000 Series on to a wall

requires two screws. The heads of the screws

should be 5 to 7 mm in diameter, the shafts should

be 3 to 4 mm in diameter, and the length of the

screws should be more than 10.5 mm.

- 5 -

NOTE

Wall mounting is certified for use in maritime applications.

Software Installation Information

For the NPort’s configuration, the default IP address of the NPort is:

LAN: Static; IP = 192.168.127.254; netmask = 255.255.255.0.

NOTE

If you have forgotten the NPort's IP address, use the Device

Search Utility (DSU) from your PC to locate the NPort. After

searching the LAN for NPort units, the DSU will display the IP

address of each unit.

You may log in with the password moxa to change any setting to meet

your network topology (e.g., IP address) or serial device (e.g., serial

parameters). For first-time use, click the Wizard in the left navigation

panel. The wizard will prompt you to configure the IP address, SSID,

and security mode. For other settings, use the factory defaults or

modify the settings for your application.

For software installation, download the relative utilities from Moxa's

website:

https://www.moxa.com/support/support_home.aspx?isSearchShow=1

•Download the NPort Windows Driver Manager and install it as the

driver to run with Real COM mode of the NPort Series.

•Execute NPort Windows Driver Manager; then map the virtual COM

ports on your Windows platform.

•You may refer to the DB9 Male Ports pin assignment section to loop

back pin 2 and pin 3 for the RS-232 interface to carry out a self test

on the device.

•Use HyperTerminal or a similar program (you may download Moxa's

program, called PComm Lite) to test whether the device is working.

Pin Assignments and Cable Wiring

RS-232/422/485 (Male DB9) Pinouts

RS-232

RS-422/RS-485 (4W)

RS-485 (2W)

DCD

TxD-(A)

–

RXD

TxD+(B)

–

TXD

RxD+(B)

Data+(B)

DTR

RxD-(A)

Data-(A)

GND

DSR

–

RTS

–

CTS

–

- 6 -

4W/2W RS-485/RS-422 (Terminal Block) Pinouts

PIN RS-485 (2W)

RS-422/

RS-485 (4W)

–

TxD+(B)

–

TxD-(A)

Data+(B)

RxD+(B)

Data-(A)

RxD-(A)

–

GND

Four cables are available as optional accessories that can be used to

connect the NPort IA to RS-232 serial devices. For your convenience,

we show precise cable wiring diagrams for each of the two cables.

Optical Fiber Interface

100BaseFX

Multi-mode

Single-mode

Fiber Cable Type OM1

50/125 μm

G.652

800 MHz*km

Typical Distance

4 km

5 km

40 km

Wave-

length

Typical (nm)

1300

1310

TX Range (nm)

1260 to 1360

1280 to 1340

RX Range (nm)

1100 to 1600

Optical

Power

TX Range (dBm)

-10 to -20

0 to -5

RX Range (dBm)

-3 to -32

-3 to -34

Link Budget (dB)

Dispersion Penalty (dB)

Note: When connecting a single-

mode fiber transceiver, we recommend

using an attenuator to prevent damage caused by excessive optical

power.

Note: Compute the “typical distance” of a specific fiber transceiver as

follows: Link budget (dB) > dispersion penalty (dB) + total link loss

(dB).

Female DB9 to Male DB9

- 7 -

Female DB9 to Male DB25

Specifications

Power Requirements

Power Input

12 to 48 VDC

Power Consumption

(Input Rating)

•NPo rt IA-5150, NPort IA-5150-T, NPo rt IA -

5250, NPort IA-5250-T:

12 to 48 VDC, 435 mA (max.)

•NPo rt IA-5250I, NPort IA-5250I -T, N Po rt

IA-5150-M-ST, NPort IA -5150-M-ST-T,

MGate NPort IA-5150-M-SC, NPort IA -5150-

M-SC-T:

12 to 48 VDC, 510 mA (max.)

•NPo rt IA-5150I, NPort IA-5150I-T, N Po rt IA -

5150-S-SC, N Po rt IA -5150-S-SC-T, N Po rt

IA-5150I-S-SC, NPort IA-5150I-S-SC-T,

NPo rt IA-5150I-M-SC, N Port IA-5150I-M-

SC-T:

12 to 48 VDC, 555 mA (max.)

Operating

Temperature

0 to 60°C (32 to 140°F),

-40 to 75°C (-40 to 167°F) for –T model

Storage Temperature

-40 to 85°C (-40 to 185°F)

Operating Humidity

5 to 95% RH

Magnetic Isolation

Protection (serial)

2 kV (for “I” models)

Dimensions

Without ears:

With ears extended:

29 x 89.2 x 118.5 mm (1.14 x 3.51 x 4.67 in)

29 x 89.2 x 124.5 mm (1.14 x 3.51 x 4.9 in)

Relay Output 1 digital relay output to alarm (normal close):

current carrying capacity 1 A @ 30 VDC

Hazardous Location

UL/cUL Class 1 Division 2 Group A/B/C/D, ATEX

Zone 2, IECEx

This device complies with Part 15 of the FCC rules.

Operation is subject to the following conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including

interference that may cause undesired operation.

- 8 -

ATEX and IECEx Information

NPort IA-5150/IA-5250 Series

1. Certificate number: DEMKO 18 ATEX 2168X

2. IECEx number: IECEx UL 18.0149X

3. Certification string: Ex nA IIC T4 Gc

Ambient Range : 0°C ≤Tamb ≤60°C (For suffix without -T)

Ambient Range : -40°C ≤Tamb ≤75°C (For suffix with -T)

4. Standards covered:

ATEX: EN 60079-0:2012+A11:2013, EN 60079-15:2010

IECEx: IEC 60079-0 Ed.6; IEC 60079-15 Ed.4

5. The conditions of safe usage:

•The equipment shall only be used in an area of at least

pollution degree 2, as defined in IEC/EN 60664-1.

•The equipment shall be installed in an enclosure that provides

a minimum ingress protection of IP4 in accordance with

IEC/EN 60079-0.

•Conductors suitable for Rated Cable Temperature ≥ 100°C

•Input conductor with 28-12 AWG (max. 3.3 mm2) to be used

with the devices

NPort IA-5150I/IA-5250I Series

1. ATEX Certificate number: DEMKO 19 ATEX 2232X

2. IECEx number: IECEx UL 19.0058X

3. Certification string: Ex nA IIC T4 Gc

Ambient Range : 0°C ≤ Tamb ≤60°C (For suffix without -T)

Ambient Range : -40°C ≤ Tamb ≤75°C (For suffix with -T)

4. Standards covered:

ATEX: EN 60079-0:2012+A11:2013, EN 60079-15:2010

IECEx: IEC 60079-0 Ed.6; IEC 60079-15 Ed.4

5. The conditions of safe usage:

•The equipment shall only be used in an area of at least

pollution degree 2, as defined in IEC/EN 60664-1.

•The equipment shall be installed in an enclosure that provides

a minimum ingress protection of IP 54 in accordance with

IEC/EN 60079-0.

•Conductors suitable for Rated Cable Temperature ≥ 100°C

•Input conductor with 28-12 AWG (max. 3.3 mm2) to be used

with the devices

Address of manufacturer: No. 1111, Heping Rd., Bade Dist.,

Taoyuan City 334004, Taiwan

Otros manuales para NPort IA5150 series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Servidor de Moxa Technologies

Moxa Technologies

Moxa Technologies NPort 6250 Series Manual de usuario

Moxa Technologies

Moxa Technologies CN2600 Series Manual de usuario

Moxa Technologies

Moxa Technologies NPort 6150 Series Manual de usuario

Moxa Technologies

Moxa Technologies ioLogik E1210 Manual de usuario

Moxa Technologies

Moxa Technologies NPort 5100 Series Manual de usuario

Moxa Technologies

Moxa Technologies NPort Express DE-211 Manual de usuario

Moxa Technologies

Moxa Technologies NPort IA5450A Manual de usuario

Moxa Technologies

Moxa Technologies NPort 6250 Series Manual de usuario

Moxa Technologies

Moxa Technologies NPort 6450 Series Manual de usuario

Moxa Technologies

Moxa Technologies ioLogik E1510-T Manual de usuario

Moxa Technologies

Moxa Technologies NPort 5000AI-M12 Manual de usuario

Moxa Technologies

Moxa Technologies NPort 5210 Manual de usuario

Moxa Technologies

Moxa Technologies NPort 5210-T Manual de usuario

Moxa Technologies

Moxa Technologies MiiNePort E1-SDK Manual de usuario

Moxa Technologies

Moxa Technologies NPort 6450 Series Manual de usuario

Moxa Technologies

Moxa Technologies NPort 5200 Series Manual de usuario

Moxa Technologies

Moxa Technologies NPort 5610-16 Manual de usuario

Moxa Technologies

Moxa Technologies NPort 5130 Manual de usuario

Moxa Technologies

Moxa Technologies ioLogik R2140 Manual de usuario

Moxa Technologies

Moxa Technologies NPort 6650 Manual de usuario

Moxa Technologies

Moxa Technologies NPort 5200 Series Manual de usuario

Moxa Technologies

Moxa Technologies NPort IA5000A Series Manual de usuario

Moxa Technologies

Moxa Technologies NPort IAW5000A-I/O Series Manual de usuario

Moxa Technologies

Moxa Technologies NPort Express DE-211 Manual

Manuales populares de Servidor de otras marcas

HP AlphaServer ES47 Manual de usuario

Dell

Dell PowerEdge R410 Manual de usuario

PowerNAS

PowerNAS CMA Manual de usuario

Supero

Supero FatTwin F617R3-FT Manual de usuario

MSI

MSI P1-109N-L70 Manual de usuario

Dell

Dell PowerEdge XE9640 Manual

Dell

Dell PS4100 Instrucciones de montaje

EtroVISION

EtroVISION EV3151 Manual de usuario

NEC

NEC Express5800/T110j Manual de usuario

HP ProLiant Gen9 Manual de usuario

Compaq

Compaq ProLiant 3000 Manual

Dell

Dell PowerEdge 3YPMN Manual de usuario

iRobo

iRobo IPC2U Manual de usuario

Nortel

Nortel 1000 Con?guration guide Manual de usuario

Asus

Asus AP7500 Manual de operación y mantenimiento

Avid Technology

Avid Technology AirSpeed 5000 Manual de usuario

HP Integrity rx2600 Guía de instalación

Milestone

Milestone Husky IVO 350T Manual de usuario