Moxa Technologies UC-8410A Series Manual de usuario

P/N: 1802084100011

*1802084100011*

UC-8410A

Quick Installation Guide

Edition 2.0, April 2018

Technical Support Contact Information

www.moxa.com/support

Moxa Americas:

Toll

-free: 1-888-669-2872

Tel:

1-714-528-6777

Fax:

1-714-528-6778

Moxa China (Shanghai office):

Toll

-free: 800-820-5036

Tel:

+86-21-5258-9955

Fax:

+86-21-5258-5505

Moxa Europe:

Tel:

+49-89-3 70 03 99-0

Fax:

+49-89-3 70 03 99-99

Moxa Asia-Pacific:

Tel:

+886-2-8919-1230

Fax:

+886-2-8919-1231

Moxa India:

Tel:

+91-80-4172-9088

Fax:

+91-80-4132-1045



- 2 -

Overview

The UC-8410A Series of dual-core embedded computers support a rich

variety of communication interfaces, and come with 8 RS-232/422/485

serial ports, 3 Ethernet ports, 1 PCIe mini slot for a wireless module (not

for the -NW model), 4 digital input channels, 4 digital output channels, 1

SD card slot, 1 mSATA socket, and 2 USB 2.0 hosts. The computer's

built-in 8 GB eMMC and 1 GB DDR3 SDRAM give you sufficient memory to

run your applications, while the SD slot and mSATA socket provide you

the flexibility to expand the data storage capacity.

Package Checklist

•1 UC-8410A embedded computer

•Wall-mounting kit

•Ethernet cable: RJ45 to RJ45 cross-over cable, 100 cm

•CBL-4PINDB9F-100: 4-pin pin header to DB9 female console port

cable, 100 cm

•Quick installation guide (printed)

•Warranty card

Please notify your sales representative if any of the above items are

missing or damaged.

Panel Layout

Refer to the following figures for the panel layouts.

Front View

NOTE

The -NW model is not provided with the antenna connectors and

SIM card socket. However, all models come with a cover.

- 3 -

Rear View

Left-Side View

Installing the UC-8410A

Wall or Cabinet

The two metal brackets included with the UC-8410A can be used to attach

it to a wall or the inside of a cabinet. Using two screws per bracket, first

attach the brackets to the bottom of the UC-8410A. Next, use two screws

per bracket to attach the UC-8410A to a wall or cabinet.

Connector Description

Power Connector

Connect the 12-48 VDC power line to the UC-8410A’s terminal block. The

Ready LED will glow a steady green color when the OS is ready.

Grounding the UC-8410A

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from the

ground screw to the grounding surface prior to connecting the power.

ATTENTION

This product is intended to be

mounted on to a well-grounded

mounting surface, such as a metal panel.

- 4 -

SG: The Shielded Ground (sometimes called

Protected Ground) contact is the

right

most

contact

on the 3-pin power terminal block

connector when viewed from the angle

shown here. Connect the SG wire to an

appropriate grounded metal surface.

additional ground connector is provided just

above the power terminal block, which you

can use for grounding protection.

Ethernet Port

The 3 10/100/1000 Mbps

Ethernet ports (LAN 1, LAN 2,

and LAN3) use RJ45 connectors.

10/100

Mbps

1000

Mbps

ETx+

TRD(0)+

ETx-

TRD(0)-

ERx+

TRD(1)+

---

TRD(2)+

---

TRD(2)-

ERx-

TRD(1)-

---

TRD(3)+

---

TRD(3)-

Serial Port

The 8 serial ports (P1 to P8) use RJ45 connectors. Each port can be

configured by software as RS-232, RS-422, or RS-485. The pin

assignments are shown in the following table:

RS-232

RS-422/RS-485-4W

RS-485

DSR

–

RTS

TXD+

–

GND

TXD

TXD-

–

RXD

RXD+

Data+

DCD

RXD-

Data-

CTS

–

DTR

–

Digital Inputs and Digital Outputs

The UC-8410A has 4 digital output channels and 4 digital input channels.

Refer to the UC-8410A Hardware User's Manual for detailed pinouts and

wiring.

SD/mSATA

The UC-8410A comes with a SD card slot and an mSATA socket for

storage expansion.

- 5 -

To replace or install the SD card, or to install an mSATA card, follow these

steps:

1. Use a screwdriver to remove the screws on the rear and side panels of

the cover over the mSATA socket.

2. Remove the cover to access the SD-card slot and the mSATA socket.

3. Push the SD card in gently to release it and remove the SD card to

insert a new one in the socket. Make sure your SD card has been

securely inserted.

4. Insert the mSATA card into the socket, and then fasten the screws.

Please note that the mSATA card is NOT included in the product

package and must be purchased separately. Standard mSATA card

types have been tested with the UC-8410A computer and have been

found to work normally. For additional details, refer to the UC-8410A

hardware manual.

- 6 -

Console Port

The serial console port is a 4-pin pin-header RS-232 port that is located

below the SD card socket. Use a screwdriver to remove the two screws

holding the cover to the embedded computer’s housing. The port is used

for the serial console terminal, which is useful for viewing boot-up

messages. Use the CBL-4PINDB9F-100 cable included with the

UC-8410A-LX to connect a PC to the UC-8410A’s serial console port. For

details on configuring the UC-8410A-LX, refer to the Connecting the

UC-8410A Computer to a PC section.

Reset Button

Self-Diagnostic: The red LED will start blinking when you press the reset

button. Keep the button pressed until the green LED lights up for the first

time, and then release the button to enter diagnostic mode.

Reset to Factory Default: The red LED will start blinking when you press

the reset button. Keep the button pressed until the green LED lights up for

the second time and then release the button to start the reset to factory

default process.

USB

The UC-8410A supports 2 USB 2.0 hosts for external storage expansion.

Installing the Wireless Modules (Not for the –NW

Model)

Instructions for installing the Wi-Fi and cellular modules on the UC-8410A

computer are available in the Installing the Wireless Modules section of

the UC-8410A Hardware User's Manual.

Installing the SIM Card

Follow these steps to install the SIM card for the cellular module.

1. Unfasten the screw on the SIM card holder cover located on the front

panel of the computer.

- 7 -

2. Insert the SIM card into the slot. Make sure you insert the card in the

direction indicated above the card slot.

3. Close the cover and fasten the screw.

Powering on the UC-8410A Computer

To power on the UC-8410A, connect a terminal block to power jack

converter to the UC-8410A’s DC terminal block (located on the left rear

panel), and then connect the power adapter. Note that the Shielded

Ground wire should be connected to the right most pin of the terminal

block. It takes approximately 30 seconds for the system to boot up. Once

the system is ready, the Ready LED will light up.

Connecting the UC-8410A Computer to a PC

There are two ways to connect the UC-8410A to a PC: (1) through the

serial console port (2) using Telnet over the network. The COM settings

for the serial console port are: Baudrate=115200 bps, Parity=None,

Data bits=8, Stop bits =1, Flow Control=None.

ATTENTION

Remember to choose the “VT100” terminal type. Use the

CBL

-4PINDB9F-

100 cable included with the product to connect a

PC to the UC-8410A’s serial console port.

- 8 -

To use Telnet, you will need to know the UC-8410A’s IP address and

netmask. The default LAN settings are shown below. For initial

configuration, you may find it convenient to use a cross-over Ethernet

cable to connect directly from the PC to the UC-8410A.

Default IP Address

Netmask

LAN 1

192.168.3.127

255.255.255.0

LAN 2

192.168.4.127

255.255.255.0

LAN 3

192.168.5.127

255.255.255.0

Once the UC-8410A is powered on, the Ready LED will light up, and a

to proceed.

Linux:

Password: moxa

Configuring the Ethernet Interface

Linux Models

If you are using the console cable for a first-time configuration of the

network settings, use the following commands to edit the interfaces

file:

#ifdown –a

//Disable LAN1/LAN2/LAN3 interface first, before you

reconfigure the LAN settings. LAN 1 = eth0, LAN 2= eth1, LAN

3= eth2

#vi /etc/network/interfaces

//check the LAN interface first//

After the boot settings of the LAN interface have been modified, use the

following command to activate the LAN settings with immediate effect:

#sync; ifup –a

NOTE

Refer to the UC-8410A Series Linux Software User’s Manual for

additional configuration information.

Otros manuales para UC-8410A Series

Tabla de contenidos

Otros manuales de De oficina de Moxa Technologies

Moxa Technologies

Moxa Technologies DA-682A-DPP Series Manual de usuario

Moxa Technologies

Moxa Technologies UC-8100-LX Instrucciones de montaje

Moxa Technologies

Moxa Technologies V2416 Series Manual de usuario

Moxa Technologies

Moxa Technologies V2101 series Manual de usuario

Moxa Technologies

Moxa Technologies UC-3100 Series Manual de usuario

Moxa Technologies

Moxa Technologies THINKCORE W345 Manual de usuario

Moxa Technologies

Moxa Technologies UC-8100-ME-T Series Instrucciones de uso

Moxa Technologies

Moxa Technologies MC-5150-DC Series Manual de usuario

Moxa Technologies

Moxa Technologies V2101 series Manual de usuario

Moxa Technologies

Moxa Technologies MPC-2121 Series Manual de usuario

Moxa Technologies

Moxa Technologies UC-8112-ME-T Series Manual de usuario

Moxa Technologies

Moxa Technologies UC-8410 Instrucciones de uso

Moxa Technologies

Moxa Technologies MC-5157-AC/DC Manual de usuario

Moxa Technologies

Moxa Technologies MC-7270-MP-T Manual de usuario

Moxa Technologies

Moxa Technologies V2416A-C7 Manual de usuario

Moxa Technologies

Moxa Technologies THINKCORE W311 Manual de usuario

Moxa Technologies

Moxa Technologies DA-681A Series Manual de usuario

Moxa Technologies

Moxa Technologies DA-681C Series Manual de usuario

Moxa Technologies

Moxa Technologies DRP Series Manual de usuario

Moxa Technologies

Moxa Technologies DA-682A Series Manual de usuario

Moxa Technologies

Moxa Technologies MC-4510-C23 Manual de usuario

Moxa Technologies

Moxa Technologies BXP-C100 Series Manual de usuario

Moxa Technologies

Moxa Technologies UC-8410 Manual de usuario

Moxa Technologies

Moxa Technologies DA-681 Series Manual de usuario

Manuales populares de De oficina de otras marcas

HP m9060n - Pavilion - Elite Hoja de especificaciones

Asus

Asus E210 Series Manual de usuario

Dell

Dell Inspiron 600m Manual de usuario

Dell

Dell Inspiron 3662 Manual de usuario

TotalFlow

TotalFlow uFLO Manual de usuario

HP Presario SV7000 - Desktop PC Manual de usuario

HP ProDesk 400 G5 Manual

Logitech

Logitech MK320 Manual de usuario

Dell

Dell XPS 730 H2C Manual de usuario

Sony

Sony Vaio Series Manual de usuario

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Manual de usuario

Alto

Alto MD 250 Manual de usuario

Lenovo

Lenovo ThinkCentre Edge 72 Manual

Lenovo

Lenovo ThinkStation D20 Manual

Arbor Technology

Arbor Technology FPC-7800 Series Manual de usuario

Sony

Sony VAIO VGX-TP1 Series Manual de usuario

Asus

Asus Eee Box B204 Manual de usuario

Dell

Dell Optiplex 9010 All In One Manual de usuario