Motorola C4201H Manual de usuario
Warning: Charge the handset for 24 hours before use.
Model: C4201H
Digital Cordless Telephone
Additional Handset
Works with Motorola Models
(C4201, C4202, C4203 and
C4204)
2
1. Getting started .....................................................................3
1.1 Got everything.................................................................................................3
1.2 Location ...........................................................................................................3
1.3 Connecting the handset and charger the cordless handset ..........................4
1.4 Battery and Charging ......................................................................................5
1.5 Registration ......................................................................................................5
1.5.1 Registering an additional handset ........................................................5
1.5.2 De-register a handset............................................................................6
2. Getting to know your phone ................................................7
2.1 Overview of your handset ...............................................................................7
2.2 Handset LCD Display ......................................................................................9
2.3 Entering names and writing tips ...................................................................10
2.4 Navigating the menus....................................................................................10
3. General information ...........................................................11
3Getting started
1. Getting started
IMPORTANT
Do not place your C42H in the bathroom or other humid areas.
1.1 Got everything
• C42H handset
• C42H charger
• Power adaptor for the charger
• 2 x rechargeable Ni-MH battery cells
• User guide
1.2 Location
You need to place your C42H charger within 2 metres of the mains power wall socket so
that the cable will reach. The socket-outlet should be installed near the equipment and
should be easily accessible.
Make sure that it is at least 1 metre away from other electrical appliances to avoid
interference. Your C42H works by sending radio signals between the handset and main
base. The strength of the signal depends on where you place the main base. Placing it as
high as possible ensures the best signal.
CORDLESS HANDSET RANGE
The unit has a range of up to 300 metres outdoors when there is a clear line of sight
between the main base and handset. Any obstruction between the base and handset will
reduce the range signicantly. With the base indoors and the handset either indoors or
outdoors, the range will normally be up to 50 metres. Thick concrete and stone walls can
severely aect the range.
SIGNAL STRENGTH
The icon on your handset indicates that you are within range of the base. When out of
range of the base, the icon flashes. If you are on a call, you will hear a warning beep.
The line will hang up if the handset moves out of range of the base. Move closer to the
base. The handset will automatically reconnect to the base.
Setting up
IMPORTANT
The base station must be plugged into the mains power at all times. Do not connect the
telephone line cord into the wall socket until the handset is fully charged. Use only the
power adaptor and telephone line cord supplied with the product.
4 Getting started
1.3 Connecting the handset and charger the cordless handset
1. Plug the power adaptor into the socket marked on the underside of the charger
and plug the other end into the mains power wall socket.
2. Remove the battery cover from the back of the handset and insert the 2 x AAA NiMH
rechargeable batteries supplied. Please note the ‘+’ and ‘-’ markings inside the battery
compartment and insert in the correct direction.
3. Slide the battery cover back into place.
4. If you are charging the batteries for the rst time, place the handset on the charger to
charge for at least 24 hours continuously.
5. The display will show the handset name and number to indicate that it is registered to
the base.
IMPORTANT
Warning! Use only the approved rechargeable Ni-MH battery cells (2 x AAA Ni-MH
550mA rechargeable batteries) supplied with your C42. Please do not use alkaline or
nonrechargeable batteries. It may cause permanent damage to the product and void the
warranty.
Press down
1
Slide
2
5Getting started
1.4 Battery and Charging
BATTERY LOW WARNING
If you hear a warning beep every 2 minutes during a call, you will need to recharge the
handset before you can use it again.
BATTERY PERFORMANCE
In ideal conditions, fully charged batteries should give up to 16 hours talk time or up to 200
hours standby time on a single charge.1
Note that new batteries do not reach their full capacity until they have been put to normal
use for several days.
To keep your batteries in the best condition, leave the handset o the charger for a few
hours at a time.
Running the batteries right down at least once a week will help them last as long as
possible.
The charge capacity of rechargeable batteries will reduce with time as they wear out,
giving the handset less talk / standby time. Eventually they will need to be replaced.
After charging your handset for the rst time, subsequent charging time is about 6–8 hours
a day. Batteries and handset may become warm during charging. This is normal.
1All talk and standby times are approximate and depend on features selected and usage
pattern.
1.5 Registration
1.5.1 Registering an additional handset
You can register up to 4 handsets to your C42 main base to extend your phone system
without having to install extension sockets for each new phone.
You must register C42H to your C42 base before it can be used.
NOTE
Handset batteries must be fully charged before you start to register. Hold your handset
close to the base during the registration process.
On the C42 base:
1. Press and hold P for 5 seconds until you hear a beep. The base will remain in
registration mode for 90 seconds.
On the C42H handset:
1. If the handset is not register to a base press m and then enter the 4 digit PIN code
(default = 0000) and press m.
2. If the handset is already register to a base press m, scroll d to
Services
and press m.
3. Scroll d to
Register
and press m.
4. The display will ask for the PIN to be entered. Enter the 4 digit PIN code (default =
6 Getting started
0000) and press m. You will hear a beep if the registration is successful. The handset
is automatically assigned an available handset number. Use this number when making
internal calls.
1.5.2 De-register a handset
Use your base to de-register a handset.
1. Press m, scroll d to
Services
and press m.
2. Scroll d to
Unregister
and press m.
3. The display shows PIN, using the keypad enter the PIN and press m.
4. Scroll to the handset you want to de-register and press m to conrm.
5. Press n to return to standby.
7Getting started
2. Getting to know your phone
2.1 Overview of your handset
A Earpiece
B Display
See page 9 for an overview of the display icons.
C Menu / OK
Press to open the Menu.
Press to select menu options and to conrm a displayed option.
A
B
G
F
E
D
CI
H
M
J
N
L
K
8 Getting to know your phone
D Talk / Recall
Press to make a call.
When on an external call, press to access a Call Waiting Line when you hear the call
waiting prompt signal. Press again to toggle between the two calls. Also used with
switchboard/PABX and some network services.
Use with switchboard / PABX services and some network services.
E Hands-free
Press to switch hands-free on or o during a call.
F * / Keypad lock / Pulse to Tone dialling
Dial a *.
Press and hold to lock / unlock the keypad.
During a call, press to switch from pulse dialling to tone dialling.
G Mute
Press to switch mute on / o during a call.
H Volume up / Scroll up / Calls list
During a call, press to increase earpiece volume.
Press to scroll through the menu options, redial list, calls list and phonebook entries.
In standby mode, press to open the calls list.
I Phonebook / Back / Delete
In standby mode, press to open the phonebook menu.
Go back to previous menu level.
In editing mode, press to delete characters and digits.
J Volume down / Scroll down / Redial list
During a call, press to decrease earpiece volume.
Press to scroll through the menu options, redial list, calls list and phonebook entries.
In standby mode, press to open the redial list.
K End Call / Switch Handset on/o
Press to end a call.
Press and hold for 3 seconds to switch the handset on / o.
Press to return to standby when in the call list, redial list and phonebook.
L # / Pause / Change case
Dial a #.
When dialling or storing a number press to enter a pause (P).
Press to switch between upper and lower case during text editing.
M Intercom
Used to make internal calls and transfer calls to the corded base or other C42 handsets
registered to the base.
N Microphone
9Getting to know your phone
2.2 Handset LCD Display
Indicates an incoming call is connected or held.
Flashes to indicate an incoming call.
Indicates signal strength.
Eco plus is activated.
Indicates a missed call.
Indicates the incoming calls list is open.1
Indicates the redial list is open.
Hands-free mode is ON.
Ringer is switched o.
Flashes to indicate new voicemail messages received.2
O when you have no voicemail messages.
Indicates when you can scroll up and down through the menu or list.
Indicates that there is more information that can be viewed on the display.
1For this feature to work, you must subscribe to Caller ID Service from your network
operator. A subscription fee may be payable.
2This feature is dependent on your Network Service provider supporting the service.
Battery is fully charged
Battery is partially charged
Battery is running low
Flashes when battery is almost fully discharged
10 Getting to know your phone
2.3 Entering names and writing tips
Use the keypad letters to enter names, e.g. to store TOM:
Press 8 once to enter T.
Press 6 three times to enter O.
Press 6 once to enter M.
Press p to delete the last character or digit.
Press 1 on the handset to insert a space.
2.4 Navigating the menus
Your C42 has an easy to use system on the cordless handset and corded base.
When the handset is switched on and in standby:
1. Press m to open the main menu.
2. Then use u or d buttons to scroll through the available options.
3. Press m to validate an option.
4. Press p to go back to the previous option.
Note
If no buttons are pressed for 30 seconds, the handset returns to standby automatically.
Tabla de contenidos
Otros manuales de Teléfono de Motorola
Motorola
Motorola ELITE Manual de usuario
Motorola
Motorola FXC-851 Manual de usuario
Motorola
Motorola I670 - Nextel - IDEN Phone Manual de usuario
Motorola
Motorola FW500 Manual de funcionamiento
Motorola
Motorola V260/V262 Manual de usuario
Motorola
Motorola C42 Manual de usuario
Motorola
Motorola V120C Manual de usuario
Motorola
Motorola CT50 Manual de usuario
Motorola
Motorola STU 111/SECTEL 1000 Manual de usuario
Motorola
Motorola C139 - Cell Phone - GSM Manual de usuario
Motorola
Motorola motorolaone MACRO Manual de usuario
Motorola
Motorola Roadster 2 Manual de usuario
Motorola
Motorola Q GSM Manual de usuario
Motorola
Motorola D4A Manual de usuario
Motorola
Motorola fx1900xg Manual de usuario
Motorola
Motorola ME4056-1 Manual de usuario
Motorola
Motorola FX2000 Manual de usuario
Motorola
Motorola V150 Manual de usuario
Motorola
Motorola FX-852C Manual de usuario
Motorola
Motorola E365 Manual de usuario
