Motorline professional VARANDA Manual de usuario
!
2 people
Necessary tools
Nº10
Before Installation, check the levelness of the place
where you are going to apply the awning. Dimensions
must be parallel and level. If the balcony is not level,
it is necessary to apply
shims that allow the awning fixing plates to be
correctly installed.
Important
PRE-INSTALLATION INFORMATION
Installation manual
VARANDA AWNING
Varanda
Inside the package
Ce
Bc
Rt
Eb
Po2 Po1 Eq
Variable number
and format
C I
Sp
1
St
Si
tuning key
included
Note: Screws included, with the exception of screws that will connect St to a structure of the customer's choice.
V2.0 REV20220825
C I
Sp
Preparation of fixing supports
B
AInsert
Bottom
Top
max. 20cm
max. 100cm Assemble
Make the same assembly for the other CI profile.
Preparation of the cassete and front profile
Bc
BA
C
Disassemble Assemble
Slide front profile on fabric
Assemble again
Po1
D
3
2
max. 100cm
Eq
Si
Sp
Screw SI to Sp that is inserted into CI
respecting the measurements shown on
the side.
Place in center
Example for 6 sets of parts (Sp,
Si, St x 6), 3 sets for each
support:
Top
Assemble again
AB
CDE
FG
min. 30cm
Placement of fixing plates
4
C I
AB
CD E
F
Varanda with support tubes
Attention, it is necessary to respect the position shown
above to assemble the cassette together.
Attention, it is necessary to respect the position shown
above to assemble the cassette together.
Support tube example
Adapt the fixing of the awning to the type of balcony you have.
C I
Varanda without support tubes
min. 30cm
Si
St
St's distances will be equal to SI's distances in CI.
Make a mark where you will drill. Drill in the marked areas.
Screw St to the perforated base.
Screw St to SI. Repeat, as many
times as necessary, all processes
for the installation to complete.
Other supports
5
Varanda without support tubes
Simple guide
Dual Guide
Varanda with support tubes
Simple guide
Dual Guide
Cassette installation
6
A
BC
7Placement of the maneuver rope
B
C
Eb
Attention, for the awning to function correctly, pay
close attention to the following instructions.
Operation to be carried out on the 2 reinforcements.
Face
Front profile
Cover
50cm
Disassemble
A
50cm
D
Pull the end of the rope by hand and lock in the grip. The tension must be identical on both sides, to verify that the pulley is well positioned
in the center of the front profile. Make sure the rope is properly guided on all the pulleys in the system. Open the awning all the way down.
Place the awning with 50 cm of opening, to make more tension of the rope. Perform an opening and closing maneuver. The fabric must be
taut.
8Fabric tension
9Limit switch regulation
Course stoppers are factory preset. To manually adjust see next page.
End of assembly
BC
B
D
Eb
C
D
Rt
Po2
Face Cover
Front profile
2 part pre-assembly
Winding direction
to
P1
NOT
OK
Attention, from B to
C, make sure that
the rope does not
wrap itself, as it may
break after a lot of
use.
from
to
Then, slide the rope through the profile, pass
the rope through the pulley and slide it again
along the profile to the load bar.
Attention: the cover will be placed when the
rope is tensioned.
All respecting the winding direction, make 3 courses
of the wire around the winding tube pulley and fix.
Pass the thread under the pulley P1 by sliding it
through the guide and finding the bottom cover at C.
from
to
B
D
10 Finalization
After the adjustments have been made, replace the cassette cover and the front profile cover by tightening the two screws.
P1
Eb
Po1
Ac
Po2
P2
P2
Direction of travel
the rope takes when
it is assembled
(overview)
Note:
1) Pulley Po1 must be placed in
the middle of the front profile.
2) Po1 →Ac =20cm
3) The rope passes first under and
then over Po1.
Pin up
Ac Po2
2
0
cm
1
2
3
D
from
Po1
to
3Limit switch regulation
Course stoppers are factory preset. To adjust, open
the awning. Then open the cassette and on the right
side you will see the mechanism as shown in the
figure to the side.
To adjust the closing:
- Close the awning and then open it up to 30cm;
- On the mechanism, use the tuning key on the
lower protrusion;
- When turning to the right, the awning closes more;
- When turning to the left the awning opens more.
To adjust the opening:
- Awning open to the end;
- On the mechanism, use the tuning key on the
upper protrusion;
- When turning to the right, the awning opens more;
- When turning to the left, the awning closes more.
Note: When regulating several times, the motor may need
to rest.
Limit switch - closing
Consumer information
1Electronic operation
Use the remote control to open and/or close the awning electronically.
Open
2Manual operation
In the event of a breakdown or power failure, use the awning in manual mode with the help of the emergency crank.
To open, turn the emergency crank to the right. To close, turn the emergency crank to the left.
Insert the emergency crank as indicated in the figure above.
Limit switch - opening
closes more
opens more closes more
opens more
A
B
BA
A
A
B
B
B
B
A
A
Close
Awning maintenance tips
An awning is subject to some adverse situations: humidity, sea air, counterweight, wind, among others. We recommend:
- check the tightness of screws and limit switches after installation and regularly at the beginning and end of each season;
- never roll up a wet awning. Dry it if possible;
- clean the fabric and frame at the beginning and end of each season. Attention, never use detergents.
Problems Causes Solutions
Varanda awning disintegrated
from the structure.
The front profile does not work
normally.
The fabric is not stretched.
The awning does not open or close.
The electric awning maneuvers do
not work.
The electric awning maneuvers do
not work.
The fixing supports are not adapted to the
structure's composition.
The rope came off from a pulley. The tension
of one rope is higher than the other (pulley
Po1 off-center).
Incorrect tension in the base.
Fabric deformation (Natural effect).
Rupture of the rope.
Faulty electrical maneuver.
The motor goes into thermal protection after
two successive descents and one ascent.
Connection problem.
Check the correct placement of the supports (as
indicated in the manual).
In case of fixing with a chemical anchor bolt, report
to the manufacturer.
Check the entire rope circuit for possible rope
displacement (paragraph 6).
Check that the tension is identical on both sides
(pulley Po1 centered - paragraph 6).
Tighten the rope (paragraph 7).
Do the complete circuit of the rope again (par. 6).
Test the electrical part to find the problem.
Wait for the end of protection (20 minutes).
Check the motor connection.
Check the operation of the motor by connecting
directly to the electrical input (blue black or blue brown).
Do not install the awning in the event of:
Wind Rain Nothing suspended
Snow
EXPLODED VIEW
TVAR07
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
N.R*
N.R*
* the part is not represented
TVAR19
TVAR04/05
MTTCU14A
MTC678P
TVAR17
MTL001
TVAR14/15
TVAR13
TUB90M8MT
TVAR24
TVAR01
TVAR16
TVAR06
TVAR03
TVAR02
TVAR23
TVAR22
TVAR09
TVAR18
TVAR20/21
Cassette Guide
Cassette lateral covers
Tube Support Ø78mm
Tube Bushing Ø78mm
Cassette pulley
Tube Ø78mm
Cassette Superior Profiles
Cassette Bottom Profile
Tubular motor
Motor support
Guide
Guide cover
Strut cover
Strut profile
Strut Profile Cover
Fabric Tension Pulley
Fabric Tension Spring Pulley
Fabric Tension Spring
Rope
Rope Brakes
Number Reference Designation
7
6
5
4
3
2
1
8
910
11
12
13
14
15
16
17
18
TVAR08 TVAR10
Otros manuales de Accesorios de Motorline professional
Motorline professional
Motorline professional WIWEATHER Manual de uso y cuidado
Motorline professional
Motorline professional COFRE 260 Manual de operación e instalación
Motorline professional
Motorline professional MF101 Manual de usuario
Motorline professional
Motorline professional MF1 Manual de usuario
Motorline professional
Motorline professional COFRE 600 VOLANTE Manual de operación e instalación
Motorline professional
Motorline professional BRISA SOLAR Manual de uso y cuidado
Motorline professional
Motorline professional MONOBLOCO 300 Manual de operación e instalación
Motorline professional
Motorline professional COFRE 260 Manual de operación e instalación
Motorline professional
Motorline professional MF103 Manual del propietario
Motorline professional
Motorline professional MR27 Manual de uso y cuidado
