Morse Hydra-Lift 400A-60 Manual de usuario

morsedrum.com

The Specialist In Drum Handling Equipment

Model 400A-60

Hydra-Lift, 60”, Manual Lift & Tilt

CONTENTS

Page

Receiving Procedures. . . . . . . . . . . . . . . . . 1

Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Safety Information. . . . . . . . . . . . . . . . . . . . . 1 - 2

Machine Description. . . . . . . . . . . . . . . . . . . 3 - 4

Accessories. . . . . . . . . . . . . . . . . . . . 3

Assembly Instructions. . . . . . . . . . . . . . . . 4 - 5

Start-Up Procedure. . . . . . . . . . . . . . . . 6

Operating Instructions. . . . . . . . . . . . . . . . . . 6 - 7

Maintenance. . . . . . . . . . . . . . . . . . . . . . . 7

Safety Information

While Morse Manufacturing Co. drum handling equipment is

engineered for safety and e󰀩ciency, a high degree of responsibility

must be placed upon the machine operator to follow safe practices,

based primarily on common sense, upon which true safety

depends.

Failure to follow the safety precautions in this manual can result in

personal injury or property damage. Observe the same precautions

as with similar machinery where carelessness in operating or

maintenance is hazardous to personnel. Carefully read the safety

precautions below and throughout this manual.

Receiving Procedures

Every Morse drum handler is inspected prior to shipping. However,

damage may be incurred during transit.

• Check for visible damage. If you choose to accept damaged

freight, always sign noting the damage on the BILL OF LADING.

• Document the damage and have the truck driver sign. We

recommend keeping a digital camera at your receiving dock for

this purpose.

• Open packages expeditiously to check the condition of the

goods. There is only a 24 hour window to notify the carrier of any

concealed damage.

• IMMEDIATELY REPORT ALL DAMAGE TO THE SHIPPING

COMPANY! Then you may contact Morse for assistance with

your freight claim.

• Morse Manufacturing will not be held responsible for any

damaged freight that is not signed for as damaged.

Delivery to non-business addresses without a loading dock result

in additional freight charges. Residential delivery fees, inside

delivery fees, re-delivery charges, and lift gate services will be

added by the truck line, and are non-negotiable.

Limited 2 Year Warranty

Morse drum handling equipment is guaranteed against defects in

workmanship or materials for TWO YEARS when used properly

within its rated capacity. Warranty does not cover wear from

normal use or damage from accident or abuse. Motors and

other purchased parts carry the warranties of their manufacturers.

For warranty claims, contact your Morse Dealer to obtain a

return authorization number, and for return freight advice. Return

freight must be prepaid.

In all instances, liability is limited to the purchase price paid or to

repairing or replacing the product. Customer assumes liability for

any modications, unauthorized repairs or parts substitution.

Operator’s Manual

for Morse Hydra-Lift Drum Karrier

with Manual Lift and Tilt

Model 400A-60

Serial Number 0414 to ____ (MMYY)

The Specialist In Drum Handling Equipment

Model 400A-60

Hydra-Lift, 60”, Manual Lift & Tilt

Operator’s Manual for Morse Hydra-Lift Karrier with Manual Lift and Tilt

Model 400A-60 Serial Number 0414 to ____ (MMYY)

morsedrum.com

Safety Information (continued)

DANGER - Indicates a situation which, if not avoided, will result in serious

injury or death. This signal word is limited to the most extreme situations.

WARNING - Indicates a situation which, if not avoided, could result in serious

injury or death.

CAUTION - Indicates a situation which, if not avoided, can result in damage to

the machine.

CAUTION – Do Not Transport with Drum Raised

ALWAYS LOWER THE DRUM HOLDER TO LOWEST POSITION BEFORE TRANSPORTING. The

unit can become unstable when transporting with a raised load.

DANGER - Stay Clear of Power Lines

KEEP WELL CLEAR OF POWER LINES. Never approach a power line. Current in a high voltage line

may arc some distance from the wire to the steel framed, grounded machine.

WARNING

The Hydra-Lift Karrier is designed to handle one drum of the types listed at the top of page 3, under 2.

Machine Description. DO NOT attempt to handle any other type of drum or object. DO NOT exceed

the weight capacity.

WARNING - Level Floors Only

For operation only on clean, level oors of suitable bearing capacity. Do not use on sloped surfaces,

ramps, irregular or debris strewn oors.

WARNING - Do Not Modify the Unit

Under no circumstances should any modications be made to the Morse machinery without factory

authorization. Any modications may void the warranty. This machine was designed to perform a

specic job and alterations may result in injury to operator or machine.

WARNING - No Loose Fitting Clothing

Wear close-tting clothing and safety equipment appropriate to the job. Loose tting clothing may

become caught on the machinery and cause severe personal injury.

WARNING - Hydraulic Fluid Under Pressure Can Be Hazardous

Escaping hydraulic uid under pressure can penetrate the skin, causing serious injury. Avoid the

hazard by relieving pressure before disconnecting hydraulic lines. Keep hands and body away from

pinholes and nozzles, which eject uid under high pressure. Use a piece of cardboard to search for

leaks. If an accident occurs, see a doctor immediately and inform them of the nature of the accident.

CAUTION - Wear Safety Shoes

Wear safety shoes with non-slip soles and hard toe protection.

WARNING: This product can expose you to chemicals including barium sulfate, cobalt, titanium

dioxide, and 2-methylimidazole, which are known to the State of California to cause cancer, and

bisphenol-A, which is known to the State of California to cause birth defects or other reproductive harm.

For more information go to www.P65Warnings.ca.gov

Operator’s Manual for Morse Hydra-Lift Karrier with Manual Lift and Tilt

Model 400A-60 Serial Number 0414 to ____ (MMYY)

morsedrum.com

The Specialist In Drum Handling Equipment

Model 400A-60

Hydra-Lift, 60”, Manual Lift & Tilt

Machine Description

Model 400A-60 Hydra-Lift Karrier will pour a drum up to 72” (183 cm) high,

measured from the oor to the lowest point of a horizontal drum. It is

designed to lift, transport, and dispense a 55-gallon (210 liter) steel drum

22” to 23.5” (56 to 59.7 cm) in diameter.

Maximum full-drum capacity is 800 Lb. (363 kg). Capacity is derated to

500 Lb. (227 kg) for a half-full drum. Half-full rating is based on the tilt

mechanism’s capacity for handling an unbalanced bottom-heavy drum.

Kit # 2690-P

Hand Wheel

16” (40.6 cm) diameter

Hand Wheel with

speed knob. Replaces

standard pull chain to

turn drum.

Kit # 3900-P

MORStopTM Tilt-Brake

Automatically holds

drum tilt angle until you

move it.

ACCESSORIES

to Install on EXISTING Manual Tilt Drum Handler

55/30 Series Diameter Adapters for drum with diameter smaller than 22” (56

cm). To handle a smaller drum, insert the correct size Diameter Adapter into

the standard drum holder. See Diameter Adapter info at:

https://morsedrum.com/products/diameter-adapters

ONLY Diameter Adapters for drum with 17.5” (44.5 cm) diameter or smaller

have integrated brackets to prevent drum slipping length-ways.

NOTE: For 30-gallon (114 Liter) PLASTIC drum, insert Diameter Adapter;

AND install Bracket or Top Rim Clamp to prevent drum slipping.

IMPORTANT: To prevent 30 to 55 gallon (114 to 210 L) size plastic drum from

slipping, you MUST install either Top Rim Clamp Kit or Bracket Assembly Kit.

1. Bracket Assembly Kit # 4556-P is required to handle a RIMLESS

plastic drum (gure 2.1), and is also recommended for a ber drum.

The Bracket adjusts for a 31” to 39” (79 to 99 cm) tall drum.

You can also handle a rimmed drum with the Bracket installed.

2. Top Rim Clamp Kit # 4560B-P to handle a RIMMED plastic drum

(gure 2.2). Install the Top Rim Clamp Kit to handle a RIMMED

plastic, steel or ber drum with suitable top rim.

Figure 2.2

Kit # 4560B-P

Top Rim Clamp

to handle RIMMED plastic

drum

Figure 2.1

Kit # 4556-P

Bracket Assembly

to handle RIMLESS or

RIMMED plastic drum

The Specialist In Drum Handling Equipment

Model 400A-60

Hydra-Lift, 60”, Manual Lift & Tilt

Operator’s Manual for Morse Hydra-Lift Karrier with Manual Lift and Tilt

Model 400A-60 Serial Number 0414 to ____ (MMYY)

morsedrum.com

Controls

The Morse Hydra-Lift Karrier is manually propelled and steered. There are two functions

for the operator to control (Figure 2.3):

1. “LIFT” and lower function for vertical positioning of the drum

2. “TILT” function to control the degree of rotation of the drum

LIFT and Lower Function

To raise the drum, insert pump lever handle into pump socket. With the release valve

closed, begin to pump the lever handle. The drum will lift.

To lower the drum, open the release valve slowly, a part of a turn. Allow the drum to

descend at a controlled rate. The valve may be reclosed to hold the drum at any height.

TILT Function

To tilt the drum, turn the hand crank (item 90) to turn the drum. Before releasing your

grip on the hand crank, pull out the crank stop pin (item 89) to block the hand crank from

spinning freely.

If the drum handler is equipped with the MORStop Tilt-Brake, there is no need to use the

stop pin. Braking is immediate and self-actuating, without additional steps by the operator.

Note: To add the MORStop Tilt-Brake to an existing drum handler, order Kit # 3900-P for a

eld installation kit.

Assembly Instructions

Unpack and identify the following parts:

1 Each Tower with hydraulic pump and cylinder, etc.

2 Each Legs with wheels

1 Each Overhead assembly with drum holder, etc.

1 Each Hardware Package containing:

Part # Description Quantity

1166-P WASHER, 3/8 USS 1” OD, ZINC 4

1521-P HHCS, 3/8-16 X 3 GR5 4

1169-P NUT, 3/8-16 REV HEX LOCK 4

17-P WASHER, 5/8 SAE FL 1-5/16 OD 4

6061-P PIN, CLEVIS, 400, GREASE FIT 2

NOTE: The clevis pins and mating surfaces at their joints should be

coated with grease during assembly.

Floor Lock

The screw-down oor lock is located on the base of the tower (gure 3.1). Turning the oor lock clockwise until it locks in the down

position activates the oor lock. When the oor lock is activated it prevents unwanted free wheeling of the unit. Floor conditions

determine the e󰀨ectiveness of the oor lock. The operator should verify its holding action before depending on it to hold.

Drum Holder Assembly

The MORCINCHTM Drum Holder (Saddle) assembly is the component

on intended to hold the drum. It is designed to secure a standard

ribbed 55-gallon (210 liter) steel drum around it’s middle using a cinch

chain and ratchet tightening system. It automatically adjusts for 22” to

23.5” (56 to 59.7 cm) diameter drum.

The MORCINCHTM Drum Holder also accepts accessories to handle a

plastic drum, ber drum, or a smaller diameter drum.

WARNING - Watch Out for Pinch Points - Stay clear of moving

parts. Operator should remain behind the push handle during the

lift operation.

Figure 3.1

Figure 2.3

Operator’s Manual for Morse Hydra-Lift Karrier with Manual Lift and Tilt

Model 400A-60 Serial Number 0414 to ____ (MMYY)

morsedrum.com

The Specialist In Drum Handling Equipment

Model 400A-60

Hydra-Lift, 60”, Manual Lift & Tilt

Figure 1 Figure 2

Step #3: Tip the tower up so it stands on the casters and wheels.

Step #4: Lift overhead assembly into position. A drift pin can help align the holes. Insert a greased clevis pin (item 12) through mast cap

and boom. Tighten collar set screw onto pin. See gure 3.

Step #5: Next, connect the cylinder (item 16) to the overhead assembly: Align ram eye with holes in boom clevis plates and insert a

greased clevis pin (item 12) with four 5/8” washers (item 13). Tighten collar set screw onto pin. See gure 4.

Step #1: Place tower on oor, push-handle down. See gure 1.

Step #2: Attach each leg (item 4) using two 3/8-16x3” grade 5 bolts (item 2), at washers (item 3), and lock nuts (item 13) as shown. Wheels

should be parallel when assembled properly. See gures 1 & 2.

Figure 3 Figure 4

The Specialist In Drum Handling Equipment

Model 400A-60

Hydra-Lift, 60”, Manual Lift & Tilt

Operator’s Manual for Morse Hydra-Lift Karrier with Manual Lift and Tilt

Model 400A-60 Serial Number 0414 to ____ (MMYY)

morsedrum.com

Operating Instructions

1. Push the Hydra-Lift Karrier to the drum.

2. Using the “LIFT” control as described in “Machine Description -

Controls” (page 3) , position the drum holder assembly with the back

band at the middle of the drum. (Figure 3.1). With the ratchet plate

swung open and the cinch chain hanging from the chain hook, push

the unit until the back band rests rmly against the drum. Some

adjustment to the tilt angle of the saddle may be necessary to ensure

band ts ush on the drum.

3. Attaching the drum: Drape the chain across the front of the drum and

engage a link into the notch in the ratchet (Figure 3.2). Turn the ratchet

clockwise to tighten chain. If ratchet turns until the pawl is beyond the

last ratchet tooth, turn the ratchet back and slide the next link into the

ratchet notch and try tightening again. The chain must be held tightly

against the drum with the pawl engaged securely in the ratchet teeth.

4. Operate the lift function to lift drum clear of oor. Roll to dispensing

location. NOTE: Do noto allow the drum to impact on oor, pouring

station, etc. or a spill or damage could occur.

CAUTION – Do Not Transport with Drum Raised

ALWAYS LOWER THE DRUM HOLDER TO LOWEST POSITION BEFORE TRANSPORTING.

The unit can become unstable when transporting with a raised load.

5. Lift drum to desired pouring height. Operate the tilt control as described in “Machine Description - Controls” (page 3) to adjust the

drum attitude. This is especially important when lifting an open drum. The oor lock should be engaged while dispensing / draining.

6. When dispensing is complete, tilt drum back to upright position. Disengage the oor lock and lower the drum to transporting height;

about 6” o󰀨 the oor.

- - IMPORTANT - -

START-UP Procedure

Machine is shipped with hydraulic uid.

BEFORE operation, REMOVE the RED shipping

plug from the hydraulic reservoir. REPLACE with

supplied BLACK breather.

Insert pump handle into pump socket.

Figure 3.2

Operator’s Manual for Morse Hydra-Lift Karrier with Manual Lift and Tilt

Model 400A-60 Serial Number 0414 to ____ (MMYY)

morsedrum.com

The Specialist In Drum Handling Equipment

Model 400A-60

Hydra-Lift, 60”, Manual Lift & Tilt

WARNING - Stay Clear of Raised Drum

NEVER allow anyone to be below any part of a raised drum handler or drum. Remain behind the

push handle while handling a drum.

WARNING – Do NOT Disengage the Cinch Chain When Drum is o󰀨 the Ground

When the drum is in the upright position, lower the drum to the oor before releasing the cinch chain.

7. Push the unit to the drum storage area and lower to the oor in an upright position. Release the cinch chain from the ratchet by

applying pressure to the ratchet handle in a clockwise direction with one hand and opening the pawl to free the ratchet with the other

hand. Remove the cinch chain link from the ratchet.

Maintenance

• Periodic inspection for the general condition of structural and mechanical components is imperative for safe and e󰀩cient operation.

• Periodically inspect all moving parts, framework, and contact areas for signs of wear, fatigue, or loosening. Tighten, adjust, or

replace parts as necessary to prevent failure and maintain proper function.

• Inspect the hydraulic system for oil drips, hose damage, or other signs of wear. Inspect the level and condition of the hydraulic uid.

Replace any parts that show signs of wear.

• Grease wheel bearings periodically. Oil or grease all moving parts including: the three clevis pins and the surfaces of the boom which

contact the inside of the mast cap, the hinge pin, the gears and sprockets in the tilt drive, and the ratchet and pawl.

• Worn or damaged parts must be properly replaced with the correct, genuine Morse parts.

• Hydraulic pump should be lled with the provided quart of Mobil ATF D/M (Morse part # 3983-P). Material safety data sheet (MSDS)

is available online. Change oil yearly, sooner depending on dirty conditions or outdoor use.

Otros manuales para Hydra-Lift 400A-60

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de elevación de morse

morse

morse 185A-HD Manual de usuario

morse

morse PILOT 900 Manual de usuario

morse

morse 510M-114 Manual de usuario

morse

morse 905 Manual de usuario

morse

morse 185A-GR Manual de usuario

morse

morse 195A-A Manual de usuario

morse

morse 400AM-60 Manual de usuario

morse

morse 515-N-115 Manual de usuario

morse

morse 86 Manual de usuario

morse

morse 525-T-115 Manual de usuario

morse

morse 82A-GT Series Manual del operador

morse

morse 85AM Manual de usuario

morse

morse 400A-96-127 Manual de usuario

morse

morse Hydra-Lift 400A-60 Manual de usuario

morse

morse 91 Manual de usuario

morse

morse 400A-72-120 Manual de usuario

morse

morse 400A-96-117 Manual de usuario

morse

morse Kontrol-Karrier 185A Manual de usuario

morse

morse 400A-72SS-110 Manual de usuario

morse

morse 510M Manual de usuario

morse

morse 152 Manual de usuario

morse

morse 400A-60-114 Manual de usuario

morse

morse 525-N-115 Manual de usuario

morse

morse 82H-SS-125 Manual de usuario

Manuales populares de Sistema de elevación de otras marcas

Braun

Braun NL955 Series Manual de usuario

haacon

haacon 1889.10 Manual de usuario

Protekt

Protekt AT 252 Manual de usuario

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Manual de usuario

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Manual de usuario

Genie

Genie Z-60/34 Manual de usuario

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Manual de usuario

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Manual de usuario

Custom Equipment

Custom Equipment Hy-Brid 3 Series Manual de programación

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Manual de programación

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Manual de programación

BERG

BERG BeNomic EasyLeaf Manual de usuario

Powermate

Powermate LiftGate LG-3 Manual de usuario

Snorkel

Snorkel TM12 Series Manual de usuario

Terberg

Terberg OMNIDEKA Manual de usuario

Harmar Mobility

Harmar Mobility AL625 Instrucciones de funcionamiento

Rotary

Rotary SPO16 Manual de usuario

Ricon

Ricon Mirage F9T Manual de usuario