morse 400A-72SS-117 Manual de usuario
The Specialist In Drum Handling Equipment
Model 400A-72SS-117
Stainless Steel Hydra-Lift, 72”,
AC Power Lift & Tilt
morsedrum.com
Copyright 2022 - Morse Mfg. Co., Inc. Form OM400A-72SS-117 (400000-______) (Updated 26 Sep., 2022) 1
Operator’s Manual
for Morse
Stainless Steel Hydra-Lift Drum Karrier
Model 400A-72SS-117
Serial Number 400000 to ______
Safety Information
While Morse Manufacturing Co. drum handling equipment is
engineered for safety and eciency, a high degree of responsibility
must be placed upon the machine operator to follow safe practices,
based primarily on common sense, upon which true safety
depends.
Failure to follow the safety precautions in this manual can result in
personal injury or property damage. Observe the same precautions
as with similar machinery where carelessness in operating or
maintenance is hazardous to personnel. Carefully read the safety
precautions below and throughout this manual.
Receiving Procedures
Every Morse drum handler is inspected prior to shipping. However,
damage may be incurred during transit.
• Check for visible damage. If you choose to accept damaged
freight, always sign noting the damage on the BILL OF LADING.
• Document the damage and have the truck driver sign. We
recommend keeping a digital camera at your receiving dock for
this purpose.
• Open packages expeditiously to check the condition of the
goods. There is only a 24 hour window to notify the carrier of any
concealed damage.
• IMMEDIATELY REPORT ALL DAMAGE TO THE SHIPPING
COMPANY! Then you may contact Morse for assistance with
your freight claim.
• Morse Manufacturing will not be held responsible for any
damaged freight that is not signed for as damaged.
Delivery to non-business addresses without a loading dock result
in additional freight charges. Residential delivery fees, inside
delivery fees, re-delivery charges, and lift gate services will be
added by the truck line, and are non-negotiable.
Limited 2 Year Warranty
Morse drum handling equipment is guaranteed against defects in
workmanship or materials for TWO YEARS when used properly
within its rated capacity. Warranty does not cover wear from
normal use or damage from accident or abuse. Motors and
other purchased parts carry the warranties of their manufacturers.
For warranty claims, contact your Morse Dealer to obtain a
return authorization number, and for return freight advice. Return
freight must be prepaid.
In all instances, liability is limited to the purchase price paid or to
repairing or replacing the product. Customer assumes liability for
any modications, unauthorized repairs or parts substitution.
CONTENTS
Page
Receiving Procedures. . . . . . . . . . . . . . . . . 1
Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Safety Information. . . . . . . . . . . . . . . . . . . . . 1 - 2
Machine Description. . . . . . . . . . . . . . . . . . . 3 - 4
Accessories. . . . . . . . . . . . . . . . . . . . 3
Start-Up Procedure. . . . . . . . . . . . . . . . 5
Operating Instructions. . . . . . . . . . . . . . . 5 - 6
Maintenance. . . . . . . . . . . . . . . . . . . . . . . 6
The Specialist In Drum Handling Equipment
Model 400A-72SS-117
Stainless Steel Hydra-Lift, 72”,
AC Power Lift & Tilt
Operator’s Manual for Morse Hydra-Lift Karrier Model 400A-72SS-117
Serial Number 400000 to ______
morsedrum.com
Copyright 2022 - Morse Mfg. Co., Inc. Form OM400A-72SS-117 (400000-______) (Updated 26 Sep., 2022) 2
Safety Information (continued)
DANGER - Indicates a situation which, if not avoided, will result in serious injury or
death. This signal word is limited to the most extreme situations.
WARNING - Indicates a situation which, if not avoided, could result in serious
injury or death.
CAUTION - Indicates a situation which, if not avoided, can result in damage to the
machine.
CAUTION – Do Not Transport with Drum Raised
ALWAYS LOWER THE DRUM HOLDER TO LOWEST POSITION BEFORE TRANSPORTING. The
unit can become unstable when transporting with a raised load.
DANGER - Stay Clear of Power Lines
KEEP WELL CLEAR OF POWER LINES. Never approach a power line. Current in a high voltage line
may arc some distance from the wire to the steel framed, grounded machine.
WARNING
The Hydra-Lift Karrier is designed to handle one drum of the types listed at the top of page 3, under 2.
Machine Description. DO NOT attempt to handle any other type of drum or object. DO NOT exceed
the weight capacity of 800 Lb. (363 kg).
WARNING - Level Floors Only
For operation only on clean, level oors of suitable bearing capacity. Do not use on sloped surfaces,
ramps, irregular or debris strewn oors.
WARNING - Do Not Modify the Unit
Under no circumstances should any modications be made to the Morse machinery without factory
authorization. Any modications may void the warranty. This machine was designed to perform a
specic job and alterations may result in injury to operator or machine.
WARNING - No Loose Fitting Clothing
Wear close-tting clothing and safety equipment appropriate to the job. Loose tting clothing may
become caught on the machinery and cause severe personal injury.
WARNING - Hydraulic Fluid Under Pressure Can Be Hazardous
Escaping hydraulic uid under pressure can penetrate the skin, causing serious injury. Avoid the
hazard by relieving pressure before disconnecting hydraulic lines. Keep hands and body away from
pinholes and nozzles, which eject uid under high pressure. Use a piece of cardboard to search for
leaks. If an accident occurs, see a doctor immediately and inform them of the nature of the accident.
CAUTION - Wear Safety Shoes
Wear safety shoes with non-slip soles and hard toe protection.
WARNING: This product can expose you to chemicals including barium sulfate, cobalt, titanium
dioxide, and 2-methylimidazole, which are known to the State of California to cause cancer, and
bisphenol-A, which is known to the State of California to cause birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov
The Specialist In Drum Handling Equipment
Model 400A-72SS-117
Stainless Steel Hydra-Lift, 72”,
AC Power Lift & Tilt
Operator’s Manual for Morse Hydra-Lift Karrier Model 400A-72SS-117
Serial Number 400000 to ______
morsedrum.com
Copyright 2022 - Morse Mfg. Co., Inc. Form OM400A-72SS-117 (400000-______) (Updated 26 Sep., 2022) 3
Machine Description
The Model 400A-72SS-117 Hydra-Lift Karrier will pour a drum up to 72” (183
cm) high, measured from the oor to the lowest point of a horizontal drum. It is
designed to lift, transport, and dispense a 55-gallon (210 liter) steel drum 22” to
23.5” (56 to 59.7 cm) in diameter.
The maximum full-drum capacity is 800 Lb. (363 kg). The capacity is derated
to 500 Lb. (227 kg) for a half-full drum. The half-full rating is based on the tilt
mechanism’s capacity for handling an unbalanced bottom-heavy drum.
55/30SS Series Stainless Steel Diameter Adapters for drum with diameter
smaller than 22” (56 cm). To handle a smaller drum, insert the correct size
Diameter Adapter into the standard drum holder. See Diameter Adapter info at:
https://morsedrum.com/products/diameter-adapters
ONLY Diameter Adapters for drum with 17.5” (44.5 cm) diameter or smaller
have integrated brackets to prevent drum slipping length-ways.
NOTE: For 30-gallon (114 Liter) PLASTIC drum, insert Diameter Adapter;
AND install Bracket or Top Rim Clamp to prevent drum slipping.
IMPORTANT: To prevent 30 to 55 gallon (114 to 210 L) size plastic drum from
slipping, you MUST install either Top Rim Clamp Kit or Bracket Assembly Kit.
1. Stainless Steel Bracket Assembly Kit # 4556SS-P
is required to handle a RIMLESS plastic drum (gure 2.1),
and is also recommended for a ber drum. The Bracket
adjusts for a 31” to 39” (79 to 99 cm) tall drum.
You can also handle a rimmed drum with the Bracket installed.
2. Stainless Steel Top Rim Clamp Kit # 4560BSS-P to handle a
RIMMED plastic drum (gure 2.2). Install the Top Rim Clamp Kit to
handle a RIMMED plastic, steel or ber drum with suitable top rim.
ACCESSORIES
Figure 2.2
Stainless Steel
Kit # 4560BSS-P
Install Top Rim Clamp Kit
to handle RIMMED plastic
drum
Figure 2.1
Stainless Steel
Kit # 4556SS-P
Install Bracket Assembly Kit
to handle RIMLESS or
RIMMED plastic drum
The Specialist In Drum Handling Equipment
Model 400A-72SS-117
Stainless Steel Hydra-Lift, 72”,
AC Power Lift & Tilt
Operator’s Manual for Morse Hydra-Lift Karrier Model 400A-72SS-117
Serial Number 400000 to ______
morsedrum.com
Copyright 2022 - Morse Mfg. Co., Inc. Form OM400A-72SS-117 (400000-______) (Updated 26 Sep., 2022) 4
Figure 3.1
WARNING - Watch Out for Pinch Points
Stay clear of moving parts. Operator
should remain behind the push handle
during the lift operation.
Floor Lock
The step-down oor lock is located behind the base (gure
3.1). To activate, step down on the oor lock until it locks
in down position. When oor lock is activated it prevents
unwanted free wheeling of unit. Floor conditions determine
eectiveness of oor lock. Operator should verify its holding
action before depending on it to hold.
Drum Holder Assembly
The MORCINCHTM Drum Holder (Saddle) assembly is the component
on intended to hold the drum. It is designed to secure a standard
ribbed 55-gallon (210 liter) steel drum around it’s middle using a cinch
chain and ratchet tightening system. It automatically adjusts for 22” to
23.5” (56 to 59.7 cm) diameter drum.
The MORCINCHTM Drum Holder also accepts accessories to handle a
plastic drum, ber drum, or a smaller diameter drum.
Figure 2.3
Motor Information
Motor is dual voltage and can be wired for 1-phase 110V 50Hz or 1-phase 220V
50Hz. Motor does NOT come with switch, cord or plug. Consult an electrician
to install and wire according to local codes.
Controls
There are two functions for the operator to control (Figure 2.3):
1. “LIFT” and lower function for vertical positioning of the drum
2. “TILT” function to control the degree of rotation of the drum
1. LIFT and Lower Function
To raise the drum
a. Plug the motor into power supply.
b. Turn the motor on by holding the momentary switch in the on position.
c. With the motor on, raise the LIFT handle.
To lower the drum
a. With the motor o, push in the LOWER handle.
2. TILT Function
To tilt the drum forward for pouring
a. Turn on the motor by holding momentary switch in the on position.
b. With the motor on, raise the tilt handle.
To return the drum to vertical position
a. Turn on the motor by holding momentary switch in the on position.
b. Push the tilt handle down.
The Specialist In Drum Handling Equipment
Model 400A-72SS-117
Stainless Steel Hydra-Lift, 72”,
AC Power Lift & Tilt
Operator’s Manual for Morse Hydra-Lift Karrier Model 400A-72SS-117
Serial Number 400000 to ______
morsedrum.com
Copyright 2022 - Morse Mfg. Co., Inc. Form OM400A-72SS-117 (400000-______) (Updated 26 Sep., 2022) 5
Operating Instructions
1.) Push Hydra-Lift Karrier to drum.
2.) Using “LIFT” control as described in “Machine
Description - Controls”, position drum holder
assembly with back band at middle of drum. (Figure
3.1). With ratchet plate swung open and cinch chain
hanging from chain hook, push unit until back band
rests rmly against drum. Some adjustment to tilt angle
of saddle may be necessary to ensure band ts ush on
drum.
3.) Attaching the drum:
Drape chain across front of drum and engage a link into
notch in ratchet (Figure 3.2). Turn ratchet clockwise to
tighten chain. If ratchet turns until pawl is beyond last
ratchet tooth, turn ratchet back and slide next link into
ratchet notch and try tightening again. Chain must be
held tightly against drum with pawl engaged securely in
ratchet teeth.
4.) Operate lift function to lift drum clear of oor. Roll to
dispensing location. NOTE: Do not allow drum to impact
on oor, pouring station, etc. or spill or damage could
occur.
START-UP Procedure
Machine is shipped with hydraulic uid.
1. Install provided hydraulic control levers (threaded
rods with black ball handles).
2. IMPORTANT: BEFORE operation, remove the
RED shipping plug from the hydraulic reservoir, and
replace with the provided BLACK breather.
CAUTION – Do Not Transport with Drum Raised
ALWAYS LOWER THE DRUM HOLDER TO LOWEST POSITION BEFORE TRANSPORTING. The
unit can become unstable when transporting with a raised load.
5.) Lift drum to desired pouring height. Operate the tilt control as described in “Machine Description - Controls” to
adjust the drum attitude. This is especially important when lifting an open drum. The oor lock should be engaged while
dispensing / draining.
Figure 3.2
The Specialist In Drum Handling Equipment
Model 400A-72SS-117
Stainless Steel Hydra-Lift, 72”,
AC Power Lift & Tilt
Operator’s Manual for Morse Hydra-Lift Karrier Model 400A-72SS-117
Serial Number 400000 to ______
morsedrum.com
Copyright 2022 - Morse Mfg. Co., Inc. Form OM400A-72SS-117 (400000-______) (Updated 26 Sep., 2022) 6
Maintenance
Periodic inspection for the general condition of structural and mechanical components is imperative for safe and ecient
operation.
Periodically inspect all moving parts, framework, and contact areas for signs of wear, fatigue, or loosening. Tighten, adjust,
or replace parts as necessary to prevent failure and maintain proper function.
Inspect the hydraulic system for oil drips, hose damage, or other signs of wear. Inspect the level and condition of the
hydraulic uid. Replace any parts that show signs of wear.
Grease wheel bearings periodically. Oil or grease all moving parts including: the three clevis pins and the surfaces of the
boom which contact the inside of the mast cap, the hinge pin, the gears and sprockets in the tilt drive, and the ratchet and
pawl.
Worn or damaged parts must be properly replaced with the correct, genuine Morse parts.
Hydraulic pump is shipped lled with Noco Premium plus automatic transmission uid d/m. Material safety data sheet
(msds) is available online. Change oil yearly, sooner depending on dirty conditions or outdoor use. Replace oil with Mobil
dte 24 or equivalent for indoor use (Mobil dte 13 for outdoor use).
6.) When dispensing is complete, tilt drum back to upright position. Disengage the oor lock and lower the drum to
transporting height; about 6” (15 cm) o the oor.
WARNING - Stay Clear of Raised Drum
NEVER allow anyone to be below any part of a raised drum handler or drum. Remain behind
the push handle while handling a drum.
WARNING – Do NOT Disengage the Cinch Chain When Drum is o the Ground
When the drum is in the upright position, lower the drum to the oor before releasing the cinch
chain.
7.) Push the unit to the drum storage area and lower to the oor in an upright position. Release the cinch chain from the
ratchet by applying pressure to the ratchet handle in a clockwise direction with one hand and opening the pawl to free
the ratchet with the other hand. Remove the cinch chain link from the ratchet.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Sistema de elevación de morse
morse
morse 82H-125 Manual de usuario
morse
morse 400A-60-114 Manual de usuario
morse
morse 400A-72-115 Manual de usuario
morse
morse 525-N-120 Manual de usuario
morse
morse 400A-60-127 Manual de usuario
morse
morse 400AM-96-114 Manual de usuario
morse
morse MORSPEED 288-1 Manual de usuario
morse
morse 86 Manual de usuario
morse
morse 515-N-115 Manual de usuario
morse
morse Hydra-Lift Drum Karrier Manual de usuario
morse
morse Hydra-Lift 400A-96 Manual de usuario
morse
morse 185i/E Manual de usuario
morse
morse 400A-60-110 Manual de usuario
morse
morse 510M Manual de usuario
morse
morse 400A-72SS-125 Manual de usuario
morse
morse 400A-96SS-114 Manual de usuario
morse
morse 400A-72-114 Manual de usuario
morse
morse 520-115 Manual de usuario
morse
morse 515-N-125 Manual de usuario
morse
morse 905 Manual de usuario
Manuales populares de Sistema de elevación de otras marcas
Braun
Braun NL955 Series Manual de usuario
haacon
haacon 1889.10 Manual de usuario
Protekt
Protekt AT 252 Manual de usuario
R. Beck Maschinenbau
R. Beck Maschinenbau HS 600 Manual de usuario
Nova Technology International, LLC
Nova Technology International, LLC NAS Series Manual de usuario
Genie
Genie Z-60/34 Manual de usuario
Screen Technics
Screen Technics INTERFIT Vertical Up Lift Manual de usuario
Mortuary Lift
Mortuary Lift ULTIMATE 1000 Manual de usuario
Custom Equipment
Custom Equipment Hy-Brid 3 Series Manual de programación
Custom Equipment
Custom Equipment Hy-Brid Lifts 2 Series Manual de programación
Hy-Brid Lifts
Hy-Brid Lifts HB-P3.6 Manual de programación
BERG
BERG BeNomic EasyLeaf Manual de usuario
