Morphy Richards IB40622 Manual de usuario

Profile iron

steam/spray/shot

Please read and keep these instructions

www.morphyrichards.com

getting the best from your

new iron...

•Safety first

Caution must be used when handling this appliance as it does get

very hot. Always switch off the unit and allow to cool before

cleaning or storing.

40622 Rev 1 31/5/05 9:01 AM Page 1

Important safety

instructions

The use of any electrical appliance

requires the following common sense safety

rules.

Primarily there is danger of injury or

death and secondly the danger of damage

to the appliance. These are indicated in the

text by the following two conventions:

WARNING: Danger to the person!

IMPORTANT: Damage to the appliance! In

addition we offer the following safety

advice.

Location

•Do not use outdoors.

Children

•Close supervision is necessary when any

appliance is used near children.

Personal safety

•WARNING: Burns can occur from

touching hot metal parts, hot water

or steam. Use caution when you

turn a steam iron upside down,

there may be hot water in the water

tank.

•WARNING: To protect against the

risk of electric shock do not put the

appliance in water or in any other

liquid.

•Do not use the vertical steam feature on

clothes that are being worn.

•Do not leave the iron unattended whilst

plugged in or on an ironing board. Never

allow the mains lead to over hang the

work surface.

•The socket should always be off before

plugging or unplugging from the socket.

Never yank the cord to disconnect from

the socket, instead, grasp plug and pull

to disconnect.

•Do not allow the cord to touch hot

surfaces. Let the iron cool completely

before putting away. Loop cord loosely

around the iron before storing.

Other safety considerations

•Use the iron only for its intended use.

•Always disconnect the iron from the

electrical socket when filling with water

or emptying, and when not in use.

•Do not operate the iron with a damaged

cord or if the iron has been dropped or

damaged. To avoid the risk of electric

shock, do not disassemble the iron, but

telephone Morphy Richards for advice.

Incorrect reassembly can cause a risk of

electric shock when the iron is used.

Special instructions

•If your iron does not work, check the

following points:

Has the temperature control been set to

the required temperature? Is the plug in

its socket? Is the plug itself or the

socket faulty? (Check by plugging in

another appliance).

•WARNING: When not in use, your

iron should never be placed flat and

left on an ironing board.

•To prevent damage to the textile being

ironed, follow the temperature guide

carefully. (Test the inside of the hem of

the garment).

•When ironing is complete, remove the

plug from the socket, empty any

remaining water from the tank, and allow

to cool before storage.

•If you drop or severely knock your iron

this could cause internal damage even if

the outside appears alright. Have it

checked by a qualified electrician.

•It is recommended that you use up one

beaker of water by operating your iron’s

steam and shot of steam functions

before ironing any clothes as some

dripping may occur while your irons

steam system is activated.

40622 Rev 1 31/5/05 9:01 AM Page 2

Electrical requirements

Check that the voltage on the rating

plate of your appliance corresponds with

your house electricity supply which must be

A.C. (Alternating current).

If the socket outlets in your home are

not suitable for the plug supplied with this

appliance the plug should be removed and

the appropriate one fitted.

WARNING : The plug removed from

the mains lead, if severed, must be

destroyed as a plug with a bared

flexible cord is hazardous if engaged

into a live socket outlet.

Should the fuse in the 13 amp plug

require changing a 13 amp BS1362 fuse

must be fitted.

WARNING: This appliance must be

earthed.

Instructions for use

Temperature guide

Heat setting markings on the adjustable control dial of all Morphy Richards irons match

those of the International Textile Care Labelling Code.

Symbol

(120˚C Max) Cool (160˚C Max) Warm (210˚C Max) Hot

Control knob

positions

Do not

iron at all

Fabric Nylon, Acetates

e.g. Acrilan

Courtelle, Orlon

Triacetates, e.g.

Tricel/Polyester

Wool, Polyester

mixtures e.g.

Polyester/Cotton

Cotton, Linen

Rayon, Rayon

mixtures,

e.g. Rayon/Linen

Ironing Iron on wrong side

if moisture required

use damp cloth

(Not Acetate)

Fabrics requiring this

setting usually require

steam pressing for heavy

cotton, denim etc.

With water in tank Dry and spray Steam/spray/shot of steam

Without water in tank Dry ironing

40622 Rev 1 31/5/05 9:01 AM Page 3

Components of your iron

⁄Variable steam

¤Shot of steam button

‹Spray button

›Filling hole with cap

ﬁSpray nozzle

ﬂSoleplate

‡Temperature control dial with indicator

·Water tank

‚Temperature indicator light (red)

„400ml filler cup

Before use

Note: The steam facility should only be

used on garments which are suitable for

ironing at the 2 and 3 dot settings.

When ironing with the steam facility at the

2 dot setting, the steam output should be set

at the lower end of the steam range (see

variable steam section).

Textiles and clothes are supposed to

carry ironing instructions. If they don’t you

should follow the fabric guide on page 3, but

be sure to test the temperature by ironing the

hem of the garment or similar area first.

If you turn the control dial down from a

hot setting to a cooler setting, wait until the

iron temperature has stabilised before you

continue ironing.

Filling

1Make sure that the iron is not plugged in

and then set the variable steam control ⁄

to the ‘0’ position before filling the iron

with water.

2Lift up the fill cap and fill the water

through the filling hole ›into the water

tank ·, using the beaker provided. A

After filling replace the fill cap. In hard

water areas the use of distilled or

demineralised water is recommended.

WARNING: Never use battery topping

up fluid or water containing any

substances like starch, or sugar, or

defrosted water from a refridgerator.

3Always pour out the remaining water after

use. WARNING: When filling your iron

with tap water always use the beaker

provided. Never fill directly under the

tap.

Temperature control

Plug in the iron and switch on. Set the

temperature control dial Bto the

temperature required, but don’t start ironing

immediately. If you wait a few minutes, the

iron will stabilise at the required setting. Your

Morphy Richards iron is fitted with an

indicator light ‚which will go on and off

while you are ironing.

⁄

‹

›

ﬁ

ﬂ

‡

‚

„

40622 Rev 1 31/5/05 9:01 AM Page 4

This is perfectly normal as it shows that

the iron is maintaining the heat setting you

have chosen.

It is always a good idea to begin with

cool fabrics and work up to higher settings.

An iron heats up quicker than it cools

down so you’ll save time and electricity.

Features of your iron

Temperature indicator light

The indicator light shows that the iron is

warming up. When the required temperature

is reached the light will go out and will cycle

on-off during operation.

Dry ironing

You can use your iron as a dry iron only.

Make sure the variable steam control ⁄is

set to the ‘0’ symbol.

Any temperature setting may be used

depending on the garment. The spray

feature may be used provided there is water

in the tank (see filling section). You do not

need to put any water in the tank when dry

ironing only.

Spray

Press the spray button ‹and aim the

spray of water at stubborn creases. You can

do this whilst dry ironing providing there is

water in the tank. When using the water

spray it may be necessary to push the

button a few times to get the spray pump

primed.

Variable steam

Fill the iron with water as described in

‘Filling’, page 4 and insert the plug into the

electrical socket.

The steam output can be varied from

low to high by sliding the variable steam

control C. When using the iron at the

bottom of the steam range, the steam

output should be adjusted to the lowest

setting.

The steam facility should only be used

on garments which are suitable for ironing

at 2 and 3 dot setting.

Shot of steam

Press the shot of steam

button ¤to obtain a burst of

extra steam for ironing out

creases in heavy material such

as denim etc.

The shot of steam can be

used whilst dry ironing,

providing there is water in the tank, and the

temperature control is set within the steam

range.

Do not use shot of steam at

temperatures below the steam range shown

on the control.

Note: For optimum steam quality, do not

operate the shot more than three times in

succession.

higher steam

lower steam

40622 Rev 1 31/5/05 9:01 AM Page 5

Vertical steam

Hold the iron in a vertical position

between 1cm and 2cm away from the item

D. Press the shot of steam button ¤, this

will create vertical steam. This feature is

especially useful for removing creases from

hanging clothes, curtains, wall hangings,

etc.

Note; For optimum steam quality, do not

operate the shot more than three times in

succession.

No drip system

Your iron is fitted with a no drip system

which is designed to prevent water

escaping from the soleplate when the iron is

too cold.

During use, the no drip system may emit

a loud click, particularly during heat-up or

whilst cooling down. This is perfectly

normal and indicates that the system is

functioning correctly.

Emptying and storing

When you have

finished ironing,

unplug your iron.

Ensure that the

variable steam

control is set at the

‘0’ position, lift up

the fill cap and

empty any remaining

water out of the filling hole.

Do not store in the box, but in an upright

position, so that any drops of water

remaining cannot leak out and discolour the

soleplate.

Important: The flex can

be damaged if wound too

tightly around the iron after

use. Make a loose loop with

the flex and wrap it around

the iron. The iron must be

cool before winding the flex

and storing on its heel.

Maintenance

To clean a stainless steel

or anodised soleplate

(certain models only)

To keep the soleplate of your iron clean

and free of limescale, we recommend that

you use one of the gentle chrome, silver or

stainless steel cleaners that are generally

available. Always follow the manufacturers

instructions. To clean off melted man-made

fibres set the iron at 3 dot position and

pass it over a clean piece of cotton which

will draw the deposit off the surface.

To clean the exterior

Allow the iron to cool and wipe over with

a damp cloth and mild detergent, then wipe

with a dry cloth.

Helpline

If you have any difficulty with your

appliance, do not hesitate to call us.

We are more likely able to help than the

store from where you bought it.

Please have the following information

ready to enable our staff to deal with your

query quickly.

•Name of the product

•Model number as shown on the

underside of the appliance.

40622 Rev 1 31/5/05 9:01 AM Page 6

Your two year

guarantee

It is important to retain the retailers

receipt as proof of purchase. Staple your

receipt to this back cover for future

reference.

Please quote the following information if

the product develops a fault. These

numbers can be found on the base of the

product.

Model no. Serial no.

All Morphy Richards products are

individually tested before leaving the

factory. In the unlikely event of any

appliance proving to be faulty within 28

days of purchase it should be returned to

the place of purchase for it to be replaced.

If the fault develops after 28 days and

within 24 months of original purchase, you

should contact the Helpline number quoting

Model number and Serial number on the

product, or write to Morphy Richards at the

address shown. You will be asked to return

the product (in secure, adequate packaging)

to the address below along with a copy of

proof of purchase.

Subject to the exclusions set out below

(see Exclusions) the faulty appliance will

then be repaired or replaced and

dispatched usually within 7 working days of

receipt.

If for any reason this item is replaced

during the 2 year guarantee period, the

guarantee on the new item will be

calculated from original purchase date.

Therefore it is vital to retain your original till

receipt or invoice to indicate the date of

initial purchase.

To qualify for the 2 year guarantee the

appliance must have been used according

to the manufacturers instructions. For

example appliances should have been

regularly maintained.

EXCLUSIONS

Morphy Richards shall not be liable to

replace or repair the goods under the terms

of the guarantee where:

1The fault has been caused or is

attributable to accidental use, misuse,

negligent use or used contrary to the

manufacturers recommendations or

where the fault has been caused by

power surges or damage caused in

transit.

2The appliance has been used on a

voltage supply other than that stamped

on the products.

3Repairs have been attempted by

persons other than our service staff (or

authorised dealer).

4Where the appliance has been used for

hire purposes or non domestic use.

5Morphy Richards are not liable to carry

out any type of servicing work, under

the guarantee.

6Plastic filters for all Morphy Richards

kettles and coffee makers are not

covered by the guarantee.

This guarantee does not confer any

rights other than those expressly set out

above and does not cover any claims for

consequential loss or damage. This

guarantee is offered as an additional benefit

and does not affect your statutory rights as

a consumer.

•This guarantee is valid in the UK and

Ireland only.

40622 Rev 1 31/5/05 9:01 AM Page 7

Morphy Richards products are intended for

household use only.

Morphy Richards has a policy of continuous

improvement in product quality and design.

The company, therefore reserves the right

to change the specification of its models at

any time.

The After Sales Division

Morphy Richards Ltd, Mexborough

South Yorkshire, England, S64 8AJ

Helpline (office hours)

UK 0870 060 2615

Republic of Ireland 1800 409119

RN40622 MUK Rev 1 02/05

40622 Rev 1 31/5/05 9:01 AM Page 8

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Hierro de Morphy Richards

Morphy Richards

Morphy Richards breeze Manual de usuario

Morphy Richards

Morphy Richards VAPOCARE Manual de usuario

Morphy Richards

Morphy Richards IB40460 Manual de usuario

Morphy Richards

Morphy Richards breeze Manual de usuario

Morphy Richards

Morphy Richards RN40655 Manual de usuario

Morphy Richards

Morphy Richards Comfigrip Advanced 40715 Manual de usuario

Morphy Richards

Morphy Richards JET STREAM Manual de usuario

Morphy Richards

Morphy Richards Orbit Manual de usuario

Morphy Richards

Morphy Richards 40725 Manual de usuario

Morphy Richards

Morphy Richards Turbosteam iron Manual de usuario

Morphy Richards

Morphy Richards TURBOSTEAM IRON - MANUAL 2 Manual de usuario

Morphy Richards

Morphy Richards IB42270 Manual de usuario

Morphy Richards

Morphy Richards ELITE 42288 Manual de usuario

Morphy Richards

Morphy Richards SEMI-ELECTRONIC IRON RN40692 Manual de usuario

Morphy Richards

Morphy Richards Saturn Steam Manual de usuario

Morphy Richards

Morphy Richards RN40310MUK - REV 3 Manual de usuario

Morphy Richards

Morphy Richards SEMI-ELECTRONIC 40715 Manual de usuario

Morphy Richards

Morphy Richards Comfigrip Advanced 40741 Manual de usuario

Morphy Richards

Morphy Richards ORBIT TRAVEL 41540 Manual de usuario

Morphy Richards

Morphy Richards RN40635 Manual de usuario

Morphy Richards

Morphy Richards VAPOCARE Manual de usuario

Morphy Richards

Morphy Richards Power Steam Manual de usuario

Morphy Richards

Morphy Richards SEMI-ELECTRONIC 40715 Manual de usuario

Morphy Richards

Morphy Richards Turbosteam Manual de usuario

Manuales populares de Hierro de otras marcas

Clatronic

Clatronic DB 3703 Manual de usuario

TEFAL

TEFAL FV4093Z0 Manual de usuario

Gorenje

Gorenje SIH 2200 BS Manual de usuario

Philips

Philips GC6012 Manual de usuario

Bosch

Bosch 2 Series Manual de usuario

Riffel

Riffel Catena KB-819 Manual de usuario

Texi

Texi Hestia Manual de usuario

Maxwell

Maxwell MW-3010 Manual de usuario

TREVIDEA

TREVIDEA Girmi ST60 Manual de usuario

Philips

Philips HI5914/30 Manual de usuario

Primula

Primula Vapormat Manual de usuario

Magio

Magio MG-541 Manual de usuario

Scarlett

Scarlett SC-1334S Manual de usuario

Bosch

Bosch Sensixx B22L Manual de usuario

Philips

Philips GC651 Manual de usuario

Vitek

Vitek VT-1247 VT Manual de usuario

Cleanmaxx

Cleanmaxx 3397 Manual de usuario

Philips

Philips GC800 Manual de usuario