MOOSE V80FL-S Manual de usuario

user’s

guide

V80FL-S

MOBILITY SCOOTER

hello

CONGRADULATIONS ON THE PURCHASE OF YOUR NEW SCOOTER.

WE ARE QUITE CONFIDENT THAT YOU ARE GOING TO GET ALONG.

We designed this scooter with one main objective - to provide mobility,

independance and freedom, all coupled with ease of use and a touch of

style.

is user guide is intended to help you become familiar with the ins and

outs of your scooter, so that you can ensure high performance and long

life for your scooter.

We also recommend you follow the maintanece schedule outlined in this

guide, and take advantage of our trained techinicians, both for regular

maintenance, and if you should encounter your problem.

Now, without further adieu, enjoy your mobility scooter!

FEATURES

BATTERY

BATTERY F.A.Q.

OPERATION

ELECTROMAGNETIC INTERFERENCE (EMI)

SAFETY

ASSEMBLY AND DISSASSEMBLY

MAINTENANCE

SPECIFICATIONS

WARRANTY

BUYER’S REGISTRATION FORM

TABLE OF CONTENTS

e manufacturer reserves the rights of nal interpretation on the manual. For any printing mistakes or new improvements, the manufacturer will update in the new editions.

FEATURES

Modular construction - disassembles in one minute without

use of tools

Adjustable seat height

Swing away armrests

360 degrees swivel seat

Adjustable Forward/Reverse Seat

Adjustable tiller

Dynamic regenerative braking coupled with fail-safe elec

tro-mechanical disk brake

Rear wheel direct drive with dierential

Fully solid state controller

External Battery Charger

24-volt permanent magnet heavy duty DC motor

ON/OFF switch lock

Horn

Head light

Turning lights

Rear lights

Battery-charging indicator

Anti-tip-o safety wheels

Front and rear bumpers

Accessories adapter

Automatic shut o while not in use

Electronic High/Low speed switch

BATTERY

To ensure the best performance and maximum battery life, we recom-

mend frequent battery charging. Your scooter comes with an external

battery charger for your ease and convenience. e console battery

display makes charging simple and easy. Follow these steps for battery

charging.

READING YOUR BATTERY VOLUME

e console battery level display has two green lights (100% and 50%),

one yellow light (25%, you’d better charge now), and one red light (al-

most empty, you must charge them right now).

CHARGING YOUR BATTERIES

On a dry surface, turn o the power key and plug the extension cord

into the charger socket located on the steering column. en plug the

other end of the charger cord into a wall outlet.

Charge the battery for 6-8 hours depending on the usage before

charging. Disconnect the extension cord, insert key into tiller and check

if both green lights are on. If the right green light is ashing, remove the

key and reconnect the charger for a while longer.

ere is no possible way to overcharge the battery as the charging voltage

is set constant. In general, you may start charging before you go to bed at

night and disconnect it in the next morning. ere is no possible way to

overcharge the battery as the charging voltage is set constant. In general,

you may start charging before you go to bed at night and disconnect it in

the next morning.

BATTERY F.A.Q.

How does the charger work?

When your scooter’s battery voltage is low, the charger works harder,

sending more electrical current to the battery to bring up their charge.

When the voltage approaches full level, the charger is at nearly zero

amperage. erefore, when the charger is plugged in, it maintains the

charging on your scooter’s batteries, but will not overcharge them. But

we do not recommend that you charge your scooter for more than 24

consecutive hours.

What if my scooter’s batteries won’t charge?

Ensure that both ends of the charger cord are inserted fully.

How oen must I charge the batteries?

It depends on how oen you use it:

- If you use your scooter daily, charge its batteries everyday. Your scoot-

er will be ready each morning to give you a full day of service.

- If you use your scooter once a week or less, charge its batteries at least

once a week for 12 to 14 hours at a time.

- Keep your scooter’s batteries fully charged.

- Avoid discharging your scooter’s batteries.

What type and size battery should I use?

Your scooter is equipped with two deep-cycle batteries that are sealed and

maintenance free. Use only the battery model designed for this scooter

that is supplied by Moose Mobility Scooter Co.

NOTE: Sealed batteries are not serviceable. Do not remove the caps.

Why do my new batteries seem weak?

New batteries will not delivery their full capabilities until they have been

discharged and recharged in about 5 times.

How can I ensure maximum battery life?

Fully charged deep-cycle batteries provide reliable performance and

extended battery life. Keep your scooter’s batteries fully charged whenever

possible. Batteries that are regularly and deeply discharged, infrequently

charged, or stored without a full charge may be permanently damaged,

causing unreliable performance and limited service life.

OPERATION

BEFORE GETTING ONTO YOUR SCOOTER

- Have you fully charged the batteries? (See page 5, “Batteries and

charging.”)

- Ensure that the clutch realease lever in the open (power driven) po-

sition. Never leave the clutch realease lever in the close position unless

you are manually pushing your scooter.

- Ensure that the tiller lock knob is in the locked position. (See page 9,

“Disassembly and assembly.”)

OPERATING YOUR SCOOTER

- Set the speed adjustment dial to your desired speed. Set the high/low

switch for how much power you will need. Setting the switch to “high”

will increase the speed of the scooter

- Press the throttle control lever to move and release the lever to stop.

e green lever moves the scooter forward, and the red lever moves the

scooter backward.

Note: your scooter’s backward speed is slower than the forward speed

for safety reasons.

ELECTROMAGNETIC INTERFERENCE

Electromagnetic interference (EMI) from sources such as radio and TV stations, amateur

radio (HAM) transmitters, two-way radios, and cellular phones can aect powered scooter

and motorized scooters. Following the warnings listed below should reduce the chance of

unintended brake release or powered scooter movement, which could result in serious injury.

1) Do not operate hand-held transceivers (transmitters-receivers), such as citizens band

(CB) radios, or turn ON personal communication devices, such as cellular phones, while the

powered scooter is turned ON.

2) Be aware of nearby transmitters, such as radio or TV stations, and try to avoid coming

close to them;

3) If unintended movement or brake release occurs, turn the powered scooter OFF as soon

as it is safe.

4) Be aware that adding accessories or components, or modifying the powered scooter, may

make it more susceptible to EMI (Note: ere is no easy way to evaluate their eect on the

overall immunity of the powered scooter.

5) Report all incidents of unintended movement or brake release to the powered scooter

manufacturer, and note whether there is a source of EMI nearby.

If unintended motion or brake release occurs, turn the power OFF as soon as it is safe.

FDA recommends that you report all incidents of unintended motion or brake release to us

or your dealer, and if possible, note whether there was a radio wave source nearby at the time

of the incident. You may also report to FDA’s Med Watch problem reporting program. Call

1-800-FDA-1088 and ask for Form 3500.

e following warning label is included in order to make users always aware that a possibility

of electromagnetic interference exists.

We highly recommend you visit the support page on our website, moosemobilityscooter.

com/support, to learn more about electromagnetic interference.

SAFETY

Your scooter can negotiate grass, gravel, dirt, and sand surfaces, as well

as hard paved or carpeted surfaces. However, extra caution should be

taken when operating your unit on uneven surfaces other than at

surfaces.

You should also be aware of the potential eect of electromagnetic

interference (EMI) on scooter operation. More information about EMI

can be found on the previous page or on our website at www.moosemo-

bilityscooter.com/support

- DO NOT drive o or over obstacles exceeding 5 cm in height.

- DO NOT make abrupt changes in direction at high speed or while

traveling on an incline.

- DO NOT climb inclines greater than 12 degrees or a rise of 2 meters

in 10 meters.

- DO NOT travel on highways and freeways; ALWAYS stay in the bike

lanes and sidewalks.

- DO NOT operate your unit when the red battery indicator light is

ashing.

- DO NOT operate your unit with the clutch lever in the disengaged

position.

- DO NOT mount or dismount your unit with power switch in the “ON”

position.

- ALWAYS make sure that the steering tiller adjustment knobs are tight.

- ALWAYS make sure that the seat is locked so that it will not swing

during operation.

- WE RECOMMEND using a seat belt and bike helmet for safety.

- DO NOT turn ON or use hand-held personal communication devices,

such as citizens band (CB) radios and cellular phones, while your scooter

is turned ON.

- BE AWARE of nearby transmitters, such as radio or TV stations and

hand-held or mobile two-way radios, and try to avoid coming close to

them.

- BE AWARE that adding accessories or components, or modifying your

scooter, may make it more susceptible to interference from radio wave

sources.

ASSEMBLY AND DISSASSEMBLY

e scooter has been designed to assembled and disassembled quick-

ly and easily without the use of tools. Excessive force should not be

required. If you encounter a problem, please refer to the User’s Guide,

then try again. If the problem persists, don’t hesitate to call your autho-

rized dealer for assistance.

PIECES

e scooter consists of the following main modules, which you can put

together or dismantle without using any tools:

(1) Front chassis (2) Rear chassis (3) Seat (4) Two batteries

(5) Rear fairing

ASSEMBLY

(1) Clean the two joint heads on the rear chassis.

(2) Position the front and rear chassis such that the joint heads and

holes are aligned.

(3) Taking the wheels as swinging pivots li the front and rear chassis

slightly till the heads and holes are at the same level.

(4) Pull the two chassis together.

(5) Insert the security pins into the positioning holes.

(6) Plug the control cable from the front chassis into the receptacle

on the rear chassis.

(7) Adjust the tiller angle by loosening and tightening the knobs at the

lower and upper joints.

(8) Place batteries onto the oor pan and secure them.

(9) Join each battery with the branched cable rst, and then join it with

the receptacle from the controller box.

(10) Join all cables with the same labeling, except the cable for turning

lights.

(11) Put the rear fairing in place and connect the cable for the turning

lights.

(12) Set the seat on the seat post and lock the seat in position by tighten-

ing the knob.

(13) Adjust the height of the seat by bolt on the seat post under the seat.

Tabla de contenidos

Manuales populares de Patinete eléctrico de otras marcas

Drive Medical

Drive Medical ODYSSEY GT Manual de usuario