Moog Sub 37 Manual de usuario

SUB 37 SynthSound Libraries

New SUB 37 SynthSound Pack

Owner's Manual

New SUB 37 SynthSound Pack

Introduction to New SUB 37 SynthSound Pack

Thank you for purchasing the Massive Leads.

Massive Leads

Contents: 32 new presets for Moog Sub 37 including: Moog Sub 37 Firmware 1.1.13

Updater and “ SendSX “ Tool.

Synthsound proudly announces a great collection of aggressive leads and soft plucked

synths taken from the progressive music: it provides 32 new patches by

synths taken from the progressive music: it provides 32 new patches by lex Di Donna

lex Di Donna

( SynthSound )

( SynthSound ).

.

This pack pushes your Moog Sub 37 over the edge of its capabilities.

2

New SUB 37 SynthSound Pack

System requirements

To install the “ Massive Leads ” you'll need:

●

●SUB 37 firmware1.1.13 or later

SUB 37 firmware1.1.13 or later

●

●32 free slots

32 free slots

To load the libraries into memory you'll need:

●

●Sysex Program ( MIDI OX Send SX etc... )

Sysex Program ( MIDI OX Send SX etc... )

●

●USB Cable (A / B ) or Midi 5 pin cable

USB Cable (A / B ) or Midi 5 pin cable

Preparations before installing

To install the “ Massive Leads” you'll need SUB 37 system version 1.1.13 or later and at

least 32 slots of free space on your synth ( See the Sub_37_Update_Instructions.pdf for

manual firmware update instructions ).

When you send a preset message via sysex the preset is loaded into your SUB 37 buffer

data ( temporary memory ) and it can be played immediately.

If you press any preset button or power off the synth before saving it the preset will be

erased from the buffer.

You will need to load it again in order to play it.

If you want to save these presets in a SUB 37 memory location use the “SAVE” hardware

buttons and proceed to a manual saving as soon as you send the Sysex from your

computer.

3

New SUB 37 SynthSound Pack

Massive Leads

Installing

Installing SynthSound Packs

SynthSound Packs

1.

1. Make sure your Sub 37 runs OS 1.1.13 or later.

Make sure your Sub 37 runs OS 1.1.13 or later.

2.

2. Use your PC / Laptop to unzip the downloaded file in a new folder.

Use your PC / Laptop to unzip the downloaded file in a new folder.

3.

3. Un-zip the downloaded files.

Un-zip the downloaded files.

4.

4. Connect your Sub 37 via USB cable or MIDI.

Connect your Sub 37 via USB cable or MIDI.

5.

5. Install “ SendSX.exe ” and open the program at the end of the installation

Install “ SendSX.exe ” and open the program at the end of the installation

process.

6.

6. Open the file “ Sub37_Massive.syx “

Open the file “ Sub37_Massive.syx “

7.

7. Check if your device has been recognized by the program selecting “Midi

Check if your device has been recognized by the program selecting “Midi

Out” and “Midi In “ on the program.

8.

8. If your device has been recognized, then you can proceed to send the .syx

If your device has been recognized, then you can proceed to send the .syx

file.

9.

9. Press “ Send ( F4 ) “.

Press “ Send ( F4 ) “.

10.

10. Enjoy your new sounds!

Enjoy your new sounds!

4

New SUB 37 SynthSound Pack

Terms of Use

Please note that all pre-existing bank data used by any library will be overwritten. Since

our sound libraries have been created from scratch you must have free user locations. We

are free of any liability for any potential loss of user data or any keyboard malfunction. The

use of purchased libraries by Synthsound is granted for studio recordings and live

performances.

5

Moog Sub 37 Manual de usuario

Manuales populares de Sintetizador de otras marcas