Montpellier MLM308BG Manual de usuario

Refrigerator

MLM308BG

Instructions for Use

GUIDELINES CONCERNING THE SAFETY OF USE

GENERAL INFORMATION

DESCRIPTION OF THE APPLIANCE, BASIC PARTS

INSTALLATION AND OPERATING CONDITIONS OF THE

APPLIANCE

ELECTRONIC CONTROL PANEL DESCRIPTION. TEMPERATURE

REGULATION

USING THE REFRIGERATOR EFFICIENTLY

DEFROSTING

CLEANING AND CARE

TROUBLE-SHOOTING

TRANSPORT

ENVIRONMENTAL PROTECTION

PRODUCT FICHE

GUIDELINES CONCERNING THE SAFETY OF USE

Some provisions in this user manual are unified for refrigerating products of

different types (for a refrigerator, refrigerator-freezer or freezer). CAREFULLY

READ THE INSTRUCTION MANUAL. The Manufacturer shall not be held liable

for damage arising from the failure to observe the instructions contained in this

manual. Keep this manual for future reference, or to pass it over to the next

user.

–Do not cover the ventilation holes at the top and on the sides of the appliance.

–Do not use any mechanical means or electrical devices to hasten the thawing

process when cleaning the freezer compartment.

–Do not use electrical appliances inside the food storage compartments of the

appliance, unless they are of the type recommended by the manufacturer.

–If the supply cord is damaged it must be replaced by the manufacturer,

manufacturer service agent or a similarly qualified person, in order to avoid a

hazard.

–Disposal of the appliance should be according to national rules.

–Do not damage the appliance refrigeration system. It contains the refrigerant

gas R600a. If the refrigeration system is damaged:

•Do not use any open flame.

•Avoid sparks―do not turn on any electrical appliances or lighting

fixtures.

•Immediately ventilate the room.

–Air the room in which the appliance is placed for a few minutes (the size of the

room for a product containing isobuthane / R600a must be at least 4 m3) to

avoid damage to the cooling system.

–Do not allow children to play with the appliance or to plug it in or unplug from

the electricity supply socket. Do not allow children to play with the packaging

material from the appliance.

–This appliance can be used by children aged from 8 years and above and

persons with reduced physical, sensory or mental capabilities or lack of

experience and knowledge if they have been given supervision or instruction

concerning use of the appliance in a safe way and understand the hazards

involved.

–Cleaning and user maintenance shall not be made by children without

supervision.

The appliance should only be connected to an earthed socket installed in

accordance with the regulations. Make sure that the supply voltage

corresponds with the voltage marked on the rating label. This product

complies with all binding CE labelling directives. The earthed electrical

socket by which the appliance is connected to the mains should be in an

accessible place. It is a legal requirement that the appliance is properly

earthed. The manufacturer will not be held liable for any damage or injury

which may result from the failure to fulfil this requirement.

–TO AVOID THE EXPOSURE TO DANGER, ALWAYS HAVE FAULTY CABLE

BE REPLACED ONLY BY THE MANUFACTURER, BY OUR CUSTOMER

SERVICE OR BY QUALIFIED PERSON AND WITH A CABLE OF THE SAME

TYPE.

–It is forbidden to readjust or modify any parts of the unit. It is crucial not to

damage the capillary tube visible in the compressor recess. The tube may not

be bent, straightened or wound. If the capillary tube is damaged by the user

the guarantee will be void.

–It is forbidden to use a technically damaged appliance.

–The appliance can’t be disposed of by burning.

–Do not store beverages in bottles and cans, especially carbonated beverages,

in the freezer chamber. The cans and the bottles may explode.

–Do not put frozen products, taken out directly from the freezer (lollies, ice

cubes, etc.) into your mouth; their low temperature may cause severe frost-

bite.

–The appliance should be used only for freezing and storing foodstuffs.

–This appliance is not designed for the storage of explosive substances such as

aerosol cans with a flammable propellant.

–It is prohibited to store petrol and other flammable liquids near the appliance.

–The appliance operates properly at the ambient temperature (see product

fiche). Do not use it in the cellar, unheated summer cottage during autumn and

winter.

–Pull the plug out from the mains socket before each maintenance activity. Do

not pull on the cord, but hold the body of the plug instead.

–When performing activities, such as cleaning, maintenance or moving, the

appliance must be completely disconnected from power supply (by pulling the

plug out from the socket)

–If the appliance is unplugged (for cleaning, moving to another place, etc.), it

may be repeatedly switched ON AFTER 15 MIN.

–Do not place any switched on electrical devices (such as microwave ovens,

hair dryers, irons, electric kettles or other electrical devices) on top of the

appliance because this may cause ignition of plastic parts.

–Do not place any dishes with liquids on top of the appliance and do not keep

flowers in vases or other liquid-filled vessels on the appliance.

–Do not climb on or sit on the appliance, do not lean on or hang on the

appliance doors and do not allow children to do this.

DO NOT TRY REPAIR THE APPLIANCE ON YOUR OWN. ALWAYS

CONTACT AN AUTHORIZED TECHNICIAN. TO AVOID THE

EXPOSURE TO DANGER, ALWAYS HAVE FAULTY CABLE BE

REPLACED ONLY BY THE MANUFACTURER, BY OUR CUSTOMER

SERVICE OR BY QUALIFIED PERSON WHIT A CABLE OF SAME

TYPE.

ATTENTION! DO NOT REMOVE THE COVER OF THE LIGHT EMITTING

DIODE (LED) LUMINAIRE! If the cooling appliance is equipped with light

emitting diode (LED) luminaire and the lighting is not functioning, please contact

a maintenance technician to have it replaced. THE LUMINAIRE CAN BE

REPLACED ONLY BY A MAINTENANCE TECHNICIAN!

GENERAL INFORMATION

The appliance is a refrigerator intended for a short-term storage of chilled products.

THE APPLIANCE IS ECOLOGICALLY CLEAN, CONTAINING NO MATERIALS HARMFUL TO

THE OZONE LAYER: the refrigerant used is R600a, the foaming agent used for the

appliance insulation is cyclopentane C5H10.

THE MANUFACTURER GUARANTEES RELIABLE OPERATION OF THE REFRIGERATOR

WHEN THE RELATIVE AIR HUMIDITY NOT GREATER THAN 70 PER CENT AND THE

AMBIENT TEMPERATURE IS:

+16 TO +32 DEGREES CELSIUS (Climate class N);

+16 TO +38 DEGREES CELSIUS (Climate class ST).

+16 TO +43 DEGREES CELSIUS (Climate class T).

DESCRIPTION OF THE APPLIANCE, BASIC PARTS



The pull-out drawer 5 moves on roller

bearings 17. The drawer can be

removed by pulling it out and lifting it

off the rails.

Electronic control display

Fruit and vegetable box

On / off switch for interior light

Door trays

Shelf for bottles

Egg tray

Adjustable height shelves

Condenser

Pull-out drawer

Thaw water drip tray

Glass shelf

Compresor

INSTALLATION AND OPERATING CONDITIONS OF

THE APPLIANCE

Installation before using the appliance for the first time

It is recommended to prepare the appliance for operation with a helper.

•Remove package. Lift the appliance away from foamed polystyrene base. Tear off

adhesive tapes.

•When positioning the appliance in chosen location, it will move more easily into

position if you lift the front a little and incline it backward, allowing it to roll on its

casters. Moving or positioning the appliance do not tilt it by more than 40° from the

vertical position.

When placing, moving, lifting the appliance, do not hold the door

handles, do not pull the condenser at the rear part of the refrigerator

and do not touch the compressor unit.

•Remove all red-coloured parts from the

shelves. Tear away the adhesive tapes from

the door trays –they are intended only for

the transport of the appliance.

NOTE. When you open the freezer

compartment door a little red packing detail will fall out –IT IS FOR

TRANSPORTATION PURPOSES ONLY.

•Take two supports 1from the bag and insert

them into the guides 2at the top back part of the

appliance (see picture).

If the appliance is brought in from the cold (temperature is not higher than +12

°C), you should wait for two hours before connecting it to the mains.

The appliance should not be connected to the mains until all packing and

transport materials aren’t removed. Suitably dispose the packaging material.

Connection to the mains

•This appliance should be connected to AC 220-240V 50Hz supply socket. The socket

must be fitted properly, and must be supplied with an earthling conduit and a 10A

fuse. It is a legal requirement that the appliance is properly earthed. The

manufacturer will not be held liable for any damage or injury which may result from

the failure to fulfil this requirement.

•Do not use adapters, multiple sockets and two-wire extension leads. If it is necessary

to use the extension lead, it must be equipped with a protection ring and a single

socket and must have a VDE/GS safety certificate.

•If an extension lead is used (with a protection ring and safety certificate), its socket

must be located at a safe distance, away from the sinks, and must not be in a place

where it could be flooded by water or waste water.

•When positioning the appliance, be careful that the electrical cord isn’t squeezed in

order to avoid its damage. Do not store heavy objects such as cooling devices,

furniture or other domestic devices next the appliance in such a way that they could

squeeze and damage the electrical cord. This can cause a short circuit and a fire.

•Make sure that the plug of the electrical cord is not squeezed by the back wall of the

appliance or otherwise damaged. A damaged plug can be the cause of a fire!

Positioning

•Place the appliance in a dry, well ventilated room.

WARNING! The appliance should not be operated in an unheated room

or porch. Place the appliance away from heat sources such as kitchen

stove/oven, radiators, or direct sunlight.

The rear wall of the refrigerator, in particular, the condenser and other elements of the

cooling system must not contact other elements, which may damage them, (e.g. central

heating pipes and the water supply pipes).

WARNING! The appliance must not touch any pipes for heating, gas or

water supply, or any other electrical devices.

Minimum distances from the heat sources:

- from the electric gas and other ovens - 30 mm,

- from oil or coal fired ovens - 300 mm,

- from built-in ovens - 50 mm

If there is no possibility of ensuring the above- mentioned distances, provide an

appropriate insulation board.

•Do not cover the ventilation holes at the top of the appliances –

it must be a good air circulation around the appliance. There

should be a gap of at least 10 cm between the top of the

appliance body and any furniture that may be above it (see fig.).

If this requirement is not followed, the appliance consumes more

electrical energy and its compressor may overheat. 

•The appliance must stand on a level surface and must not touch

the wall. If necessary, regulate the height of the appliance by

adjusting the levelling feet: by turning them clockwise –the

front of the appliance rises, by turning them counter clockwise –

it comes down. If the appliance

is tilted slightly backward –the

doors will close by themselves.

•◄If the appliance is placed in a

corner, a gap must be left between the appliance

body and the wall so that the freezer compartment

door can be opened enough to pull out the frozen

product drawer (see picture).

ELECTRONIC CONTROL PANEL DESCRIPTION.

TEMPERATURE REGULATION.

When connecting the device to the mains for the first time, the blue temperature

indicating segment lights up at +5: factory temperature setting +5 °C, but you can

select the preferred temperature according to your needs.

The appliance features and temperature are controlled with touch (sensory) buttons.

When the desired function is on, the function symbol is lit in a white colour

and when it is turned off, the symbol becomes grey.



1. Temperature adjustment button is marked with the °C symbol. You can set

the temperature of the refrigerator compartment between +1 °C and +9 °C.

Temperature setting in the refrigerator

Activate temperature button 1: tap and hold until the temperature indicating segment

starts to flash in blue (active). Then release button 1and tap repeatedly until the

required temperature segment is blue (activated). One tap changes the temperature by

one position.

The temperature setting operates in a circle: for example, the active segment is at +5,

and if you want to set +1 °C after activation you have to tap temperature button 1 3

times –until the temperature indicating segment at +1 turns blue.

Refrigerator compartment temperature is adjustable on a five-point scale:

+9 –highest temperature (lowest cooling).

+1 –lowest temperature (highest cooling).

NOTE. After power loss the device turns on automatically, saving the last user-set

temperature in the refrigerator compartment.

THE TEMPERATURE IN THE REFRIGERATOR COMPARTMENT MAY VARY

DEPENDING ON AMBIENT TEMPERATURE, THE AMOUNT OF FOODSTUFFS, THE

TEMPERATURE OF THE FOODSTUFFS, AND HOW OFTEN THE APPLIANCE

DOORS ARE OPENED AND CLOSED. Therefore we recommend:

•locate the appliance away from heat sources,

•do not put hot foodstuffs in the refrigerator –they must be cooled down to

room temperature,

•appliance door must not to be left open,

•the appliance door should not be open longer than it is necessary to take out or put in

foodstuffs

IF THE REFRIGERATOR DOOR IS OPEN MORE THAN 30 SECONDS an audible warning

signal sounds, and silenced when the door is closed.

If the room temperature is below +16 °C, we recommend that you set a lower

temperature with the temperature-selection button (1).

Cooling device on/off

SHUTDOWN. Tap and hold button 1until the three temperature indicative segments are

blue, and the light in the refrigerator compartment turns off. CAUTION! Voltage remains

turned on.

SWITCHING ON. Tap and hold button 1until the set temperature indication segment is

blue, and the refrigerator compartment lighting is on.

NOTE: after turning on the cooling device, the last temperature set by the user will be

saved.

2. Temperature indicator segments. The temperature set-point segment is

illuminated in blue (active), while the other temperature value segments are grey

(inactive).

3. The quick cooling function is activated by tapping button 3 marked with the

symbol. When the quick cooling function is on, the white segment in the centre of the

button is on.

The quick cooling function is recommended when you want to cool down quickly fresh

food products to +5 °C or when many food products are loaded into the refrigerator.

When the food products have been cooled to +5 °C, the quick cooling function turns off

automatically. If you do not want to wait until it has cooled down to the set

temperature, touch the button 3 of this function and turn the function off - the white

segment will become grey.

USING THE REFRIGERATOR EFFICIENTLY

Storage zones in the refrigerator

•Due to the natural circulation of the air in the appliance, there are different

temperature zones in the refrigerator chamber.

•Pre-packed vegetable and other fresh food with a label stating it should be kept at a

temperature of approx. +4 °C.

•The warmest area is in the top section of the door. Use this for storing butter and

cheese.

Food that should not be stored in a refrigerator.

Not all food is suitable for storing in the refrigerator, particularly:

- Fruit and vegetables which are sensitive to cold, such as bananas, avocado, papaya,

passion fruit, aubergines, peppers, tomatoes and cucumbers.

- Fruit which is not yet ripe

- Potatoes

•Do not keep prepared food and ready-to-cook (“heat and eat”) food in the same

container.

Tabla de contenidos

Otros manuales de Refrigerador de montpellier

montpellier

montpellier MITL325 Manual de usuario

montpellier

montpellier MFF186ALX Manual de usuario

montpellier

montpellier MS310-2W Manual de usuario

montpellier

montpellier MAB550C Manual de usuario

montpellier

montpellier MAB50 Manual de usuario

montpellier

montpellier MS165W Manual de usuario

montpellier

montpellier MBUL134E Manual de usuario

montpellier

montpellier MTL362X Manual de usuario

montpellier

montpellier MBUL134 Manual de usuario

montpellier

montpellier MFF152W Manual de usuario

montpellier

montpellier MITL294 Manual de usuario

montpellier

montpellier MFF170K Manual de usuario

montpellier

montpellier MBUR201 Manual de usuario

montpellier

montpellier MAB551C Manual de usuario

montpellier

montpellier MITR122 Manual de usuario

montpellier

montpellier MXD83X Manual de usuario

montpellier

montpellier MAB386 Manual de usuario

montpellier

montpellier MAB148 Manual de usuario

montpellier

montpellier MIFF5151F Manual de usuario

montpellier

montpellier MON-MRF48W Guía de instalación

montpellier

montpellier MBUR115 Manual de usuario

montpellier

montpellier MITL85 Manual de usuario

montpellier

montpellier MFF152 Manual de usuario

montpellier

montpellier MITL100 Manual de usuario

Manuales populares de Refrigerador de otras marcas

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Manual de usuario

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Manual de usuario

Sharp

Sharp SJ-BA31IEXW2-EU Manual de usuario

CORBERO

CORBERO CC2300MCW Manual de usuario

KitchenAid

KitchenAid 2205264 Manual de usuario

Stengel

Stengel KU 1101 A++ Manual de usuario

NEFF

NEFF KI181 Series Manual de usuario

Hoshizaki

Hoshizaki Reach-In Manual de usuario

Amana

Amana ASD2524VES00 Manual de usuario

BOMANN

BOMANN KGC 213 Manual de usuario

Danby

Danby DAR044A1SLDD Instrucciones de montaje

Samsung

Samsung RF323TE Manual de usuario

Beko

Beko CSA31022 Manual de usuario

IKEA

IKEA FROSTIG C 185 E Manual de usuario

Electrolux

Electrolux ER 6821 D Manual de usuario

True

True TS-28 Manual de usuario

Frigidaire

Frigidaire FSC23R5DW9 Manual de usuario

Beko

Beko LSP4579W Manual de usuario

montpellier MLM308BG Manual de usuario

Manuales populares de Refrigerador de otras marcas