MONARCH INSTRUMENT Phaser-Strobe pbx Manual de usuario

Instruction Manual

Phaser-Strobe pbx

Portable Phase-Shiing Stroboscope

15 Columbia Drive

Amherst, NH 03031 USA

Phone: (603) 883-3390 • Fax: (603) 886-3300

E-mail: [email protected]

Website: www.monarchinstrument.com

SAFEGUARDS AND PRECAUTIONS

1. Read and follow all instrucons in this manual carefully, and retain this manual

for future reference.

2. Do not use this instrument in any manner inconsistent with these operang

instrucons or under any condions that exceed the environmental

specicaons stated.

3. Certain strobe frequencies can trigger epilepc seizures in those prone to that

type of aack.

4. Users should not stare directly at the light source.

5. Prolonged exposure to the light can cause headaches in some people.

6. Objects viewed with this product may appear to be staonary when in fact

they are moving at high speeds. Always keep a safe distance from moving

machinery and do no touch the target.

7. There are lethal voltages present inside this product. Refer to the secon on

Lamp Replacement before aempng to open this product.

8. Do not allow liquids or metallic objects to enter the venlaon holes on the

stroboscope as this may cause permanent damage and void the warranty.

9. Do not allow cables extending from unit to come into contact with rotang

machinery, as serious damage to the equipment, or severe personal injury or

death may occur as a result.

10. This instrument may not be safe for use in certain hazardous environments,

and serious personal injury or death could occur as a result of improper use.

Please refer to your facility’s safety program for proper precauons.

AC Stroboscopes that have three wire mains cable must have

the earth wire connected to a suitable Earth point.

In order to comply with EU Direcve 2012/19/EU on Waste Electrical

and Electronic Equipment (WEEE): This product may contain material

which could be hazardous to human health and the environment. DO NOT

DISPOSE of this product as unsorted municipal waste. This product needs to be

RECYCLED in accordance with local regulaons; contact your local authories for

more informaon. This product may be returnable to your distributor for recycling;

contact the distributor for details.

Monarch Instrument’s Limited Warranty applies.

See www.monarchinstrument.com for details.

Warranty Registraon and Extended Warranty Coverage informaon is available

online at www.monarchinstrument.com.

Monarch Instrument holds the following US trademarks and registraons, all rights

reserved: illumiNova®, Nova-Pro®, Nova-Strobe™, DataChart™, Track-It™.

11. The product contains Nickel Metal Hydride baeries which must be disposed

of in accordance with Federal, State, & Local Regulaons. Do not incinerate.

Baeries should be shipped to a reclamaon facility for recovery of the metal

and plasc components as the proper method of waste management. Contact

distributor for appropriate product return procedures.

12. This instrument is not user serviceable. For technical assistance, contact

the sales organizaon from which you purchased the product or Monarch

Instrument directly.

TABLE OF CONTENTS

1.0 OVERVIEW ..................................................................................... 1

1.1 Display Panel / Denion of Buons ......................................... 1

2.0 PREPARATION FOR USE ............................................................... 3

2.1 Power ........................................................................................ 3

2.2 Input / Output Connecons ........................................................ 3

3.0 MENU ............................................................................................. 5

4.0 OPERATION ................................................................................... 6

4.1 Internal Mode - Standard Strobe Operaon ............................... 6

4.2 Internal Mode - TACH Frequency Generator .............................. 9

4.3 External Input Mode .................................................................. 9

4.4 Tachometer Mode - External Input Required ............................. 10

4.5 External Delay Modes (Phase Shiing) ...................................... 10

4.6 Power Up Features .................................................................... 11

5.0 USING THE STROBOSCOPE TO MEASURE RPM ............................. 12

6.0 LIMITATIONS OF REMOTE OPTICAL SENSORS ................................ 14

7.0 LAMP REPLACEMENT AND FUSE .................................................. 14

7.1 Lamp Replacement ................................................................... 14

7.2 Fuse .......................................................................................... 16

8.0 BATTERY AND POWER SUPPLY SPECIFICS ................................. 17

8.1 Low Baery Indicaon ............................................................. 17

8.2 Charging the Baeries .............................................................. 18

8.3 External Power Supply/Charger ................................................ 18

8.4 Baery Disposal ....................................................................... 19

9.0 SPECIFICATIONS ......................................................................... 19

9.1 Compliance .............................................................................. 21

10.0 ACCESSORIES, SENSORS and REPLACEMENT PARTS ................. 22

1.0 OVERVIEW

The Phaser-Strobe pbx is an extremely sophiscated instrument with many

features, yet remains simple to operate. Select only the features you need.

1.1 Display Panel / Denion of Buons

The display panel consists of a backlighted liquid

crystal display with six numeric digits on top and

ve alphanumeric digits on the boom, which

indicate modes, ash rates, etc. (see Figure 1).

Addional informaon displayed include:

PHASE Indicates Phase Shi Delay Mode is acve

TIME Indicates Phase Shi Time Delay Mode is acve

AUTO Indicates Auto Phase Shiing Mode (Virtual RPM) is acve

ALT. Indicates alternate funcon of each buon (lower secon)

and knob will be used

TACH Tachometer Mode acve (strobe won’t ash)

LOCK Unused

EXT External Input Mode acve

On Target Indicator for Tachometer Mode and Remote

Sensor in External Mode

- - - - - Indicates input frequency exceeds the limit of the stroboscope

Baery indicaon (see 8.1 Low Baery Indicaon)

Figure 1 Display Panel

Below the display are six membrane buons which control the

operaon of the stroboscope.

Mulply Flash Rate by 2

ALT Funcon - starts menu (see secon 3.0)

Hold when powering up to show all segments, then rev # and

display test

Divide Flash Rate by 2

Hold when powering up to reset factory defaults

DISPLAY/TACH

Internal/External Mode: toggles display between RPM and RPS

External Phase or Time Delay Mode: cycles display through

RPM, RPS, Phase and Time

Auto Mode: cycles display through RPM, RPS, VRPM and VRPS

ALT Funcon—toggles Tach Mode (ashing) on/o

INPUT/MEMORY

Manually toggles between Internal and External Modes

ALT Funcon—Memory, reads and stores 9 preset ash rates

ALT FUNCTION

Acvates Alternate Funcon for buons (lower secon)

and knob

PHASE DELAY

Internal Mode: toggles between normal ash rate adjust and

“phase” delay adjust

External Input Mode: cycles through External only (no delay),

Phase, Time and Auto (VRPM)

The ALT FUNCTION buon toggles ALT. in the display. When ALT. is

displayed, the buons will perform their secondary funcon listed

in the lower secon of each buon. It also changes how the tuning

knob works.

2.0 PREPARATION FOR USE

The strobe may be handheld or mounted on a tripod or other user supplied

bracket using the ¼-20 UNC bushing at the base of the handle.

2.1 Power

The Phaser-Strobe pbx has internal rechargeable baeries and may

also be powered by an external AC power supply (PSC-pbxU). If using

the internal baeries, the unit should be charged before use (see

secon 8.2 Charging the Baeries). The actual operang me of the

stroboscope depends on the ash rate and duty cycle of operaon. The

strobe can also be run connuously from the AC mains with the power

supply supplied (see secon 8.3 External Power Supply/Charger).

2.2 Input / Output Connecons

The Phaser-Strobe pbx has input and output jacks on the le side

of the stroboscope. These can be used for external triggering or

synchronizaon (daisy chaining two or more strobes). These jacks

accept 1/8" (3.5 mm) phone plugs (input - stereo, output - mono). The

input and output are TTL compable. (See Figures 2 and 3 for connector

connecon detail.)

Figure 2 Input Connector Detail (Stereo plug)

Signal Input

+6V Out to

Sensor

+6V Out to

Sensor

Signal Input

Common

(GND)

Common

(GND)

Common

(GND)

Common

(GND)

Pulse Output

from Strobe

Pulse Output

from Strobe

Figure 3 Output Connector Detail (Mono plug)

The oponal ROS-P (Remote Opcal Sensor), MT-190P (Magnec), or

IRS-P (Infrared) sensors may also be used to trigger the unit.

NOTE: When using external sensors that are powered by the Phaser-

Strobe pbx, e.g. Remote Opcal Sensor (ROS-P), the sensor must be

plugged in before the stroboscope is turned on, or the remote sensor

may not be powered up.

The input jack (▲ poinng into socket) enables an external signal to

trigger the strobe. Inserng a plug into the input jack will automacally

put the strobe into the External Input Mode. The INPUT buon can be

used to toggle between External Input Mode and Internal Mode. When

the plug is removed, the strobe will be put back into the Internal Mode.

The polarity of the input pulse can be set in the MENU opons.

With no external input, the output jack (▼poinng away from socket)

provides a TTL compable pulse from the strobe’s internal oscillator. If

an external input is applied, the output pulse is in sync with the input

pulse. This output pulse may be used to trigger a second stroboscope

synchronously to illuminate larger areas. Many strobes can be daisy

chained. The output jack of one strobe is connected to the input jack

of the next strobe causing all the strobes to ash together and be

controlled by the rst strobe in the chain. The polarity of the output

pulse can be set in the MENU opons.

3.0 MENU

The strobe has a Menu which allows the user to select sengs such as

number of decimal places, backlight on or o, posive or negave edge

for input and output signal, and input blanking on or o.

To enter the MENU:

1. Press the ALT FUNCTION buon and then the MENU buon.

2. SETUP and the menu opon will be displayed.

3. Turn the tuning knob to cycle through the main menu opons.

4. Once the desired menu opon is displayed, press the MENU buon to

select it. Press any other buon to cancel.

5. Turn the tuning knob to edit the menu opon seng.

6. Press the MENU buon to save your changes. Press any other buon

to cancel.

7. Press any buon other than MENU to exit the Main Menu.

8. DONE will be displayed.

Below is a list of the menu items:

DECPT Decimal Point (none, 1 or 2)

BLITE Backlight (Yes=On or No=O)

INPUT Posive (pos) or Negave (neg) Edge for Input Signal

OUTPT Posive (pos) or Negave (neg) Edge for Output Signal

BLANK Input Blanking (Yes=On or No=O)

4.0 OPERATION

To turn on the stroboscope, depress and hold the trigger. The trigger may

be locked in posion using the side locking buon. To lock the stroboscope

on, depress the trigger as far as it will go and then press the locking buon.

Once the locking buon is set you may release the trigger and the trigger

will be held in place. To unlock the stroboscope, simply depress the trigger

and then release.

NOTE: Unit must power down completely (OFF will be displayed and then

disappear) before unit will power on again. This is normal operaon.

There are ve (5) operang modes for the Phaser-Strobe pbx. These are

Internal, External Input, External Phase Delay, External Time Delay, and

Auto (Virtual RPM). All but the Internal Mode require an external input

signal.

In the Internal Mode, the knob adjusts the ash rate. In the External Input

Mode, an external signal is used to trigger the ash and the knob has no

eect. The External Delay Modes (Phase, Time and Auto) enable the user

to vary the stopped moon image at any point in the cycle without having

to move the trigger source locaon.

4.1 Internal Mode - Standard Strobe Operaon

In the Internal Mode, the stroboscope generates its own signals and

funcons like a tunable stroboscope. The strobe is in the Internal Mode

when nothing is plugged into the input jack or when manually set using

the INPUT buon.

Tabla de contenidos

Otros manuales de Equipo de prueba de MONARCH INSTRUMENT

MONARCH INSTRUMENT

MONARCH INSTRUMENT Nova-Pro 300 Manual de usuario

MONARCH INSTRUMENT

MONARCH INSTRUMENT Nova-Strobe BBL Manual de usuario

MONARCH INSTRUMENT

MONARCH INSTRUMENT Nova-Strobe Manual de uso y cuidado

MONARCH INSTRUMENT

MONARCH INSTRUMENT IllumiNova Series Manual de usuario

MONARCH INSTRUMENT

MONARCH INSTRUMENT Nova-Pro Series Manual de usuario

MONARCH INSTRUMENT

MONARCH INSTRUMENT PALM STROBE x Manual de usuario

MONARCH INSTRUMENT

MONARCH INSTRUMENT Nova-Strobe DBL Manual de usuario

MONARCH INSTRUMENT

MONARCH INSTRUMENT Nova-Strobe dax Manual de usuario

MONARCH INSTRUMENT

MONARCH INSTRUMENT PALM STROBE x Manual de usuario

MONARCH INSTRUMENT

MONARCH INSTRUMENT Nova-Pro Ultra Violet UV365 Manual de usuario

MONARCH INSTRUMENT

MONARCH INSTRUMENT Nova-Pro UV365 Manual de usuario

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Agilent Technologies

Agilent Technologies BERT Serial Manual de usuario

Agilent Technologies

Agilent Technologies N3280A Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Fluke

Fluke T5-600 Instrucciones de funcionamiento e instalación

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Hioki

Hioki 3169-20 Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario