MODSTER XC6 Manual de usuario
USER MANUAL/BETRIEBSANLEITUNG
SWA
1
2
SWB
1
2
DOWN
UP OK
CANCEL
BIND
POWER
6CH DIGIT AL PROPO RADIO CONTROL S YS TE M
SWC
1
2
3
SWD
1
2
Seite 2
Thank you for purchasing our product, an ideal radio system for beginners or experienced users alike.
Read this manual carefully before operation in order to ensure your safety, and the safety of others or the
safe operation of your system.
If you encounter any problem during use, refer to this manual first. If the problem persists, contact your
local dealer or visit our service and support website for help:
http://www.modster.at
Seite 3
Table of Content
1.
SAFETY 6
1.1
Safety Symbols 6
1.2
Safety Guide 6
2.
INTRODUCTION
8
2.1
System Features 8
2.2
Transmitter Overview 9
2.2.1
Transmitter Antenna 10
2.2.2
Battery lndicator
10
2.2.3
Trims 10
2.3
Receiver Overview 10
2.3.1
Receiver Antenna
10
2.3.2
Connectors 11
3.
GETTING STARTED 12
3.1
Transmitter Battery Installation 12
3.2
Connecting the Receiver and Servos 12
4.
OPERATION INSTRUCTIONS 13
4.1
Power On 13
4.2
Binding 13
4.3
Pre-use Check 14
4.4
Changing Stick Modes 14
4.5
Power Off 15
5.
FUNCTION DESCRIPTIONS
16
5.1
Flight Controls (Default Mode 2) 16
5.2
Reverse Function 17
5.3
End Points 17
5.4
Display 18
5.5
Aux Channels 18
Seite 4
5.6
Subtrim 18
5.7
Dual rate/exp. 18
5.8
Throttle Curve 19
5.9
Mixes 19
5.10
Elevon 20
5.11
V Tail 20
5.12
Assign Switches 20
5.13
Throttle Hold 21
6.
HELICOPTER FUNCTIONS 21
6.1
Pitch Curve 21
6.2
Swashplate Mix 21
6.3
Gyroscope 22
7.
SYSTEM
22
7.1
Model Select 22
7.2
Model Name 22
7.3
Type Select 22
7.4
Model Copy 22
7.5
Model Reset 23
7.6
Trainer Mode 23
7.7
Student Mode 23
7.8
Sticks Mode 23
7.9
LCD Brightness 23
7.10
Firmware Version 24
7.11
Firmware Update 24
7.12
Factory Reset 24
7.13
Aux Switches 24
8.
RX SETUP
25
8.1
RF Standard 25
8.2
RX Battery 25
8.3
Failsafe 25
8.4
Sensors List 26
8.5
Choose Sensors 26
8.6
Speed and Distance 26
8.7
ASL Pressure 27
Seite 5
8.8
Output Mode 27
8.9
i-BUS Setup 27
8.10
Servos Freq 27
9.
SYSTEM CUSTOMIZATION
28
9.1
Switching Channel Assignments 28
9.2
Activate Switch/Knob 30
10.
PACKAGE CONTENTS
30
11.
PRODUCT SPECIFICATION 31
11.1
Transmitter specification (MODSTER XC6) 31
11.2
Receiver specification (MODSTER XC6) 32
Seite 6
1.
Safety
1.1
Safety Symbols
Pay close attention to the following symbols and their meanings. Failure to follow these warnings could
cause damage, injury or death.
_!_
Danger
_!_
Warning
_!_
Attention
Not following these instructions may lead to serious injuries or death.
Not following these instructions may lead to major injuries.
Not following these instructions may lead to minor injuries.
1.2
Safety Guide
1
8
Mandatory
Do not use the product at night or in bad weather like rain or
thunderstorm. lt can cause erratic operation or loss of control.
Do not use the product when visibility is limited.
Do not use the product on rain or snow days. Any exposure to
moisture (water or snow) may cause erratic operation or loss of control.
lnterference may cause loss of control. To ensure the safety of you and
others, do not operate in the following places:
Near any site where other radio control act iv it y may occur
Near power lines or communication broadcasting antennas
Near people or roads
On any pond when passenger boats are present
Do not use this product when you are tired, uncomfortable , or under the
influence of alcohol or drugs. Doing so may cause serious injury to
yourself or others.
The 2.4GHz radio band is limited to line of sight . Always keep your
model in sight as a large object can block the RF signal and lead to loss
of control.
Never grip the transmitter antenna during operation. lt significantly
degrades signal quality and strength and may cause loss of control.
Do not touch any part of the model that may generate heat during operation,
or immediately after use. The engine, motor or speed control, may be very
hot and can cause serious burns.
(S)
Prohibited
Seite 7
Misuse of this product may lead to serious injury or death. To ensure the
safety of you and your equipment, read this manual and follow the
instructions.
Make sure the product is properly installed in your model. Failure to do so
may result in serious injury.
Make sure to disconnect the receiver battery before turning off the
transmitter. Failure to do so may lead to unintended operation and
cause an accident.
Ensure that all motors operate in the correct direction . lf not, adjust the
direction first.
Make sure the model flies within a certain distance. Otherwise, it could
cause loss of control.
Seite 8
2.
Introduction
The FS-i6X transmitter and FS-iA6 receiver constitute a 6-channel 2.4GHz AFHDS 2A digital proportional
computerized R/C system. lt is compatible with fixed-wing and helicopters.
2.1
System Features
The AFHDS 2A (Automatic Frequency Hopping Digital System Second Generation) developed and
patented by FLYSKY is specially developed for all radio control models. Offering superior protection
against interference while maintaining lower power consumption and high reliable receiver sensitivity,
FLYSKY's AFHDS technology is considered to be one of the leaders in the RC market today.
Bidirectional Communication
Capable of sending and receiving data, each transmitter is capable of receiving data
from temperature, altitude and many other types of sensors, servo calibration and i-BUS
Support.
Low Power Consumption
The system is built using highly sensitive low power consumption components,
maintaining high receiver sensitivity, while consuming as little as one tenth the power of a
standard FM system, dramatically extending battery life.
01010011 This systems bandwidth ranges from 2.408GHz to 2.475GHz. This band is divided in
135 channels. Each transmitter hops between 16 channels (32 for Japanese and Korean
versions) in order to reduce interference from other transmitters.
Unique 1D Recognition System
Each transmitter and receiver has it's own unique ID. Once the transmitter and receiver
have been paired, they will only communicate with each other, preventing other systems
accidentally connecting to or interfering with the systems operation.
l t
Seite 9
2.2
Transmitter Overview
Seite 10
2.2.1
Transmitter Antenna
_!_
Warning
_!_
Danger
For best signal quality, make sure that the antenna is at about a 90 degree
angle to the model. Do not point the antenna directly at the receiver.
Never grip the transmitter antenna during operation. lt significantly
degrades the RF signal quality and strength and may cause loss of control .
2.2.2
Battery lndicator
The status indicator is used to indicate the power and status of the transmitter and receiver. If a receiver is
not connected or bound to the transmitter no battery status will be displayed for the receiver.
2.2.3
Trims
There are 4 trims affecting stick functionality, one for ailerons (Channel 1), elevator (Channel 2), throttle
(Channel 3) and rudder (Channel4). Each time a trim is toggled, the trim will move one step. lt is possible to
make quicker trim adjustments by holding the trim in the desired direction. When the trim position reaches
the middle, the transmitter beeps in a higher tone.
2.3
Receiver Overview
2.3.1
Receiver Antenna
_!_
Attention •
For best signal quality, ensure that the receiver is mounted away from motors
or metal parts.
Otros manuales para XC6
1
Tabla de contenidos
Otros manuales de Mando a distancia de MODSTER
