Mobotix T26 Instrucciones de funcionamiento originales
Quick Installation
Door Station T26
33.095-001_EN_10/2018
2
T26 Quick Installation
Step 1 – Start The Auto Conguration
Connect And Start Up The Devices
Connect all the devices as shown in the connection diagram in the enclosed System Manual Part 1,
Chapter 2.1.3. Switch on the power supply (MxDisplay+ via PoE-switch or NPA PoE set, door station
via PoE switch). Aer the MxDisplay+ has started up, disconnect the door station briey from the
power supply (for example, remove network connector). Then restore the power supply to the door
station(s) (e.g. plug in the network plug). This restarts the boot process.
Press The Bell Button On The Camera Module
The red LED lights up approx. 5-10 s for 10 s aer the power supply has been established. Press the
light button briey during this time.
The LED now ashes once and repeats this ashing signal aer a pause of one second. Then press
the light button longer (> 2 s). The camera acknowledges the selection by a 3 s fast ash and a ring
tone aer 20 s. The autoconguration starts.
Each MxDisplay+ device is recongured from the T26 and reboots with an updated conguration.
The network data of the camera is announced (e.g. IP address). The camera LEDs will then light, the
keypad number buttons will ash white, the ESC/ALARM button will ash red, and the OK/MENU
button will ash blue.
• 5 - 10 s aer establishing
the power supply, the red
LED lights up.
• Briey press the light
button within 10 seconds.
• Then press and hold the
light button (> 2 s).
3
Step 2 – Enter Super PIN
Choose an 8 to 16 digit number. The number should not be composed only of zeros and must be
diicult to guess. Important: Make a note of the Super PIN straight away and keep it in a safe place!
Enter the Super PIN and press the OK/MENU button. Enter the Super PIN again and press the OK/
MENU button.
The input of the Super-PIN is conrmed by the KeypadRFID showing a ring-shaped ashing pattern.
Step 3 – Set Up RFID Cards
Set Up Red Admin Card
Aer you have entered your Super PIN, the keypad number buttons light up white, the bell, key and
OK/MENU buttons ash blue and the ESC/ALARM button ashes red.
Now hold the Admin card in front of the keypad for approximately ve seconds until you no longer
hear any beeps.
Set Up Blue User Cards
Aerwards, the keypad remains in Add mode for two minutes to allow you to train the User cards,
i. e.,the bell button, key button, OK/MENU button and ESC/ALARM button all ash blue.
Hold a User card to be set up in front of the keypad until a beep sounds. You can now set up as many
additional User cards as you choose, simply by holding them in front of the keypad. To exit the Add
mode before completion, press the ESC/ALARM button.
0 9
Super-PIN
OK 0 9
Super-PIN
OK
Add mode Hold in front for ve seconds Conrm
Add mode Hold briey in front Conrm
4
T26 Quick Installation
Step 4 – Customize System Via MxDisplay+
Aer the autoconguration has been completed and the access modules have been set up, you still
have to set up MxDisplay+ as the remote terminal.
Add the door stations using the installation wizard and then set up the door stations. This includes
conguring the door and door latch contacts, disabling auto-conguration, and activating recording.
Dene the ringing behaviour for each doorbell and assign the bells to the MxDisplay+ device. Set
the date and time on the device. The settings to be made are carried out on an MxDisplay+. If
several MxDisplay+ devices are used, you only need to transfer the settings of the rst device to
the other devices. A detailed description of the system adjustment can be found in the System
Manual Part 2, Section 2.4.
Step 5 – Secure System Via MxDisplay+
By securing the system, you prevent unauthorised persons from gaining unwanted access to the
door station and its remote stations. The door camera has already received secure access data with
the learning of the Super PIN: User name: admin, camera admin password: current Super PIN.
Change the MxDisplay+ web password, lock the autoconguration and save the current system
conguration. A detailed description of the system backup can be found in the System Manual
Part 2, Section 2.5.
Fig.: Aer autoconguration, the MxDisplay+ is opened in standby mode with date/time display.
Fig.: Changing the web password under menu item Administrator.
Otros manuales para T26
1
Tabla de contenidos
Otros manuales de Sistema de intercomunicación de Mobotix
Mobotix
Mobotix T25 Instrucciones de funcionamiento originales
Mobotix
Mobotix BellRFID MX-Bell1-Core Instrucciones de uso
Mobotix
Mobotix T24 Guía del usuario
Mobotix
Mobotix T24S Manual de instrucciones
Mobotix
Mobotix PC-IP102ID Manual de usuario
Mobotix
Mobotix T26 Guía del usuario
Mobotix
Mobotix T24S Guía del usuario
Mobotix
Mobotix T25 Guía de inicio rápido
Mobotix
Mobotix T24 Guía
Mobotix
Mobotix T25 Manual de usuario
Mobotix
Mobotix T25 Guía del usuario
Mobotix
Mobotix MxDisplay Plus Instrucciones de uso
Mobotix
Mobotix MxDisplay Plus Manual de usuario
Mobotix
Mobotix T24 Manual de usuario
Mobotix
Mobotix T25 Instrucciones de funcionamiento originales
Mobotix
Mobotix T24 Manual de usuario
Mobotix
Mobotix T24 Guía del usuario
