Mobius ActionCam Manual de usuario
Instruction Manual for the Mobius ActionCam
Description
The above picture shows the arrangement of the user operating features.
The two heat sinks can become very hot during operation. This is normal, but all the same you should
never leave the camera turned on where the surrounding temperature exceeds ~47° (118°F) - for
example in a car parked in the baking sun. If you wish to use the camera in very hot conditions you
should ensure the heat sinks are adequately cooled, for example by directing cool air onto the metal
plates or using a ventilator to dissipate the heat away from the metal plates. High temperatures will also
damage the internal LiPo battery. If you use your camera in very hot conditions with external power,
for example as a dashcam, you should consider replacing the battery with a Super apacitor pair. These
can be purchased from most suppliers who sell the Mobius. A Super apacitor pair enables the camera
to correctly save the last recording when external power is removed. A fully charged Supercap has
enough energy to keep the RT (Real Time lock) running for several days (about 7-10) without
external power connected. It only takes a few minutes to fully charge the Supercap.
►This manual does not cover replacing the internal battery or lens. If you need to do this, please refer
to the very detailed instructions found at http://www.rcgroups.com/forums/showpost.php?
p=25170910&postcount=4.
►This manual assumes the camera is loaded with the latest firmware available at the time of
writing. Functionality may vary with earlier or later firmware versions.
Cards
Generally speaking you may use any micro SD, micro SDH or Micro SDX card with a capacity of
up to 128GB with this camera. Larger cards are most likely also supported but not yet available. To
avoid card compatibility problems, always use quality cards with a speed rating of lass 4. There are
known problems with a few cards that have a higher class rating, for example some, but not all,
Sandisk 32GB Ultra (class 10) will not work properly with earlier firmware versions. You should use
firmware v1.17 or above with these cards. For the best compatibility use cards with a class 4 rating if
you have them. There is absolutely no advantage in using cards with a higher rating. The most
compatible cards are genuine Kingston. At the time of writing there are known problems with some
64GB cards when formatted with exFAT. For this reason it is recommended to format 64GB cards with
FAT32. 128GB cards will also work but cannot be correctly formatted to FAT32 using the built-in
formatting routine (as of firmware v2.18).
Most firmware versions support cards formatted with FAT, FAT32 or exFAT but v2.03 - v2.10 only
support FAT and FAT32. Firmware v2.18 and above support both FAT32 and exFAT. ards with a
capacity of 64GB and greater must be formatted using the In- amera formatting routine (see below) if
they are to be used with firmware v2.03 - v2.10.
Due to technical reasons you cannot update the firmware if your card is formatted as exFAT. The In-
amera formatting routine (see below) will format cards to the format required by the firmware. With
firmware versions up to v2.03 the routine will format cards with a capacity greater than 32GB to
exFAT. All other cards will be formatted as FAT/FAT32. Firmware v2.18 and above allows the user to
set which type of formatting will be used with 64GB cards and above. Older operating systems, for
example XP 64-Bit and Windows 2003, do not support exFAT file systems unless you install additional
drivers.
There are a few programs available, for example guiformat, that are capable of formatting large
capacity cards with FAT32.
►You should always use cards from well known brands. Low quality and no-name cards, as well as
some class 2 (or less) cards, may draw more than 20mA current than quality cards. This can result in
unwanted electrical noise such as clicks, chirps, hum and buzzing in the audio recording.
►The following approx. recording times for 1080p videos with a standard data rate are as
follows: 32GB ard = 4 hours 30 mins., 16GB ard = 2 hours 15 mins., 8GB ard = 1 hour 7 mins.,
4GB ard = 33 mins.
►This manual assumes a compatible S card is inserted in the card slot (except for
WebCam mode).
►The card must be carefully inserted face down with the gold contacts upwards and facing
forward. o not use force or you could damage the lock mechanism inside the card holder.
USB connector
The Mobius uses a standard Mini USB connector where pin #4 is used as a sense pin. If this pin is
connected to pin #5 (ground) then a built in USB switch will connect pin #2 to video out and pin #3
will be connected to audio-out (playback mode only). Do not connect the Mobius to a computer or
Smartphone if pin #4 is shorted to pin #5. In normal use, pin #2 carries the Data- signal and pin #3
carries the Data+ signal whereas pin #4 is unused.
Cables
The camera requires a standard USB cable for charging or connecting to external battery packs for
continuous recording. A standard USB cable is also used to connect the camera to the P in order to set
the parameters or access the camera as an external disk or webcam.
A/V-out (or Video-Out) requires a special cable where pin #4 is shorted to pin #5 (ground). When the
firmware detects pin #4 connected to ground it will output the video signal on pin #2 and the audio
signal on pin #3. Special cables can be ordered from the supplier in the form of a harness or you can
make one yourself using a 5-pin mini USB plug. You can also modify a Smartphone OTG (On The Go)
cable which already has pins #4 and #5 shorted in the mini USB plug. The audio signal is only
available in playback mode. The #16 "special" cable will not work with this camera.
You must under no circumstances use any other "special" cable, especially the "special" cable supplied
with the #11. Doing so will destroy your camera beyond repair. So, do not use a #11 "special" cable
under any circumstances.
►Always use HIGH QUALITY USB cables. Cheap cables will lead to all sorts of problems. If
possible, keep the cable as short as possible.
Video-Out (composite or TV-out
The optional Video-Out cable (see above) should always be connected or disconnected while the
camera is in standby or turned off. If the cable is connected or disconnected during recording then the
recording will be stopped and the camera will enter standby. The camera will never be recognized as a
removable drive when the video-out cable is connected.
► o not confuse this with webcam mode. The signal is an old, low resolution, composite
(TV) video signal in either PAL or NTSC format.
Before you start
Before using the camera for the first time, ensure that the internal battery is fully charged. See below
under " harging". A new, fully charged 520mAh battery will last about 80 minutes. A new, fully
charged 820mAh battery will last over 2 hours. The 820mAh battery is slightly larger and heavier than
the 520mAh battery. The batteries are interchangeable.
For recording or playback, refer to the picture above and insert a micro S card upside-down
into the S Card slot with the gold contacts pointing forward.
The Reset button
The reset button is located on the right side, above the card slot. It can be pressed by carefully inserting
a bent paper clip or similar instrument. The Reset button should only be pressed in case the
camera no longer reacts to button presses. Pressing the Reset button will force the processor
to restart. No parameter settings will be lost and the RTC (Real Time Clock) will not be
interrupted. o not confuse the reset button with the rear LE .
The Power button
Press the power button to turn the camera on. The blue LED will turn on for about 1 second before the
firmware starts to load. After about 3 seconds the yellow LED will turn on indicating the camera is
ready for use (standby). If Power On Delay is set to ON, press the power button for about 4 seconds
until the yellow LED turns on.
•Power On Delay is useful to prevent the camera from being inadvertently turned on.
•If the camera has been configured with Auto Power On Record set to On, the camera will
automatically begin recording in Mode 1.
•To turn off the camera, first stop any recordings that may be running by pressing the shutter
button and then press the power button for at least half a second (some firmware versions
require you to press the button for 2 seconds). The camera will turn off.
The Mode button
The Mode button enables the camera to be sequentially switched between 4 different modes. Each
button press advances to the next mode indicated by the LED color.
•Video Mode 1 (yellow LED). The frame rate, resolution, AOV and rotation can be individually
configured.
•Video Mode 2 (blue LED). The frame rate, resolution, AOV and rotation can be individually
configured.
•Photo Mode (red LED) which includes Time-Lapse photos.
•Playback Mode (red LED) is only possible when the special A/V-out cable is connected.
The Shutter button
Press the shutter button to start or end a video recording, to take a picture or to play/pause when in
Playback mode. Playback mode is only available when the A/V cable is attached.
LED status indicators
Since the camera has many functions, it's important to understand the meaning of the LEDs. The
following LED states are for a camera not connected to the P .
Yellow LED remains on:
•The camera is in Video Mode 1 and is on standby.
Yellow LED slowly flashes (1 sec. On, 1 sec. Off):
•The camera is in Video Mode 1 and is recording video. The Video Recording indicator (see
configuration) must be ON for this to work.
Blue LED remains on:
•The camera is in Video Mode 2 and is on standby.
Blue LED slowly flashes (1 sec. On, 1 sec. Off):
•The camera is in Video Mode 2 and is recording video. The Video Recording indicator (see
configuration) must be ON for this to work.
Red LED remains on:
•amera is in Photo Mode or Playback Mode (if an A/V cable is connected) and is on standby.
Red LED flashes once
•The camera has taken a picture
Green LED is on:
•The battery is charging.
The rear LED
When the camera is turned on, the rear LED will blink one to three times to indicate the battery charge.
Three blinks indicate a full battery, whereas one blink indicates the battery charge is getting low. The
blinks are fast. Slower blinks would unnecessarily extend the time before the camera reaches standby
mode. If the camera is configured to show the Recording Indicator, then the rear LED will normally
blink in sequence with the main LED while recording. The rear LED will not blink when Photo Mode
has been configured to take Time-Lapse Photos with a time interval of less than 2 seconds.
Connecting the camera to the PC
Make sure a card is inserted and the camera is turned OFF if you want to access the camera as an
external device (disk drive, setup). Always connect the camera directly to the P . Do not use a USB
hub.
► You cannot record video or photos if the camera is connected to the P as an external drive.
Charging
•onnect one end of the supplied standard USB cable to the camera.
•onnect the other end to a USB, 5V D power source (wall charger, P or external battery).
•When the yellow LED turns on, briefly press the Power button to turn the camera OFF.
NOTE: harging when connected to a P USB port can be toggled ON or OFF using the setup
program. When connecting to a Smartphone, you should turn this functionality OFF!
When charging, the green LED will be on, and it will turn off when the battery is fully charged.
harging takes about 2.5 hours for a fully discharged battery with the camera turned off and connected
to an external USB harger. Batteries are not covered under warranty. harging is limited to around
140mA which offers the best possible long-term battery protection. If charged with under-rated
chargers or by using a USB hub without an additional power supply, expect longer charging times. For
optimum results, the charging voltage should be +5V under load. Only use quality chargers capable of
supplying 1000mA (1A) and a stable voltage of at least 5V. Low quality chargers may not be able to
supply enough current and can lead to premature battery failure or, in the worst case, even destroy the
camera.
►A new hardware revision, released September 2014, is designed for 820mAh batteries
which have a higher capacity than the original 520mAh batteries. The new battery is
compatible with older hardware revisions but will take longer to charge. The new battery
allows recording for over 2 hours whereas the 520mAh battery will only last about 80 minutes.
All boards stamped with 2014-08-19 or later also offer over-voltage protection up to max. 24 Volt. If
the external voltage exceeds 5V the camera will not start or charge.
Formatting
Standard formatting tools provided by the operating system are not always reliable. Also, they do not
optimize the SD card's performance. For optimal card performance it is recommended to always use
the camera's built-in formatter. Instructions for In- amera Formatting are outlined below under "In-
amera Formatting". Another excellent formatting utility is "SD Formatter" which can be downloaded
from www.sdcard.org/downloads/formatter_4. This utility has been specifically designed for formatting
SD cards but will always format 64GB and greater cards to exFAT. Firmware v2.03 - v2.10 requires all
cards be formatted to FAT32 so 64GB/128GB cards must be in-camera formatted (see below).
Automatic Power Off from Standby mode
If the camera is in Standby mode (Video Mode 1, Video Mode 2 or Photo Mode) you must take a
picture(s) or start a video recording within *30 seconds. The camera will automatically turn off after
*30 seconds of no activity.
*This value can be set using the setup program. Automatic Power Off can also disabled.
When the special A/V cable is connected, automatic power-off will be disabled. This prevents signal
loss during fpv use when Standby times out.
Turn on Camera
Power-On can be configured as "fast" or "delayed". In fast mode, the camera will turn on immediately
when the Power Button is pressed. In delayed mode, press and hold the Power Button for 4-5 seconds
until the Yellow LED turns on and remains on. Irrespective of whether the camera is configured as
"fast" or "delayed" Power-on, the blue LED will turn on for a second followed by the yellow LED.
When the yellow LED remains on, the camera is ready for use.
•If the camera has been configured with "Auto Power-On Record" set to ON, the
camera will automatically begin recording in Mode 1 as soon as the power button is
pressed or external power is connected. If the recording LE has been disabled, the
yellow LE will blink 3 times and then turn off, indicating that recording has started.
Otherwise the yellow LED will slowly flash at 2 second intervals indicating that the camera is
recording.
•If the camera has been configured with "Auto Record" set to OFF (default setting), the
camera will switch to Video Mode 1 (yellow LE ) and remain in standby mode until a
button is pressed or Auto-Power-Off times out.
Turn off Camera
Press and hold the Power Button for at least half a second and then release it (some firmware versions
require you to press the button for 2 seconds). The red LED will blink 3 times and the camera will turn
off.
Switching between modes
The camera can be switched between the different modes by pressing the Mode button. Each button
click advances the camera to the next mode. Video Mode1 - Video Mode2 - Photo Mode - Playback
Mode (only if A/V cable is attached) - Video Mode1 etc.
Recording Video Mode 1 or 2 (yellow or blue LED
Start video recording and write-protecting important clips.
•Briefly press the shutter button.
•► If the recording LE has been disabled, the yellow or blue LE will blink 3 times and
then turn off, indicating that recording has started.
•► If the recording LE has been enabled, the yellow or blue LED will slowly flash at 2
second intervals indicating that the camera is recording.
•The current clip can be write-protected by pressing the Mode button while recording.
Depending on the length of the recording, the previous or next clip may also be marked as
write-protected (read-only).
Stop video recording.
•Briefly press the shutter button. The camera will return to the standby mode from which the
video was started.
Taking a Photo (red LED
•Briefly press the shutter button. The red LED will flash indicating that a picture was taken.
Playback Mode
•Ensure you have an A/V cable connected between the camera and an external monitor and a
card is inserted.
•Turn on the camera if it is not already turned on.
•Press the Mode button until the red LED turns on (Photo Mode).
•Now press the Mode button once more. The red LED will remain on, but the camera will be in
playback mode and the first frame of the first clip found on the card will show on the external
monitor.
•► If no clips are found on the card the display will show "Empty".
•Press the Shutter button to play or pause the clip.
•Press the Mode button to advance to the next clip.
•Press the Power button to exit Playback Mode and turn off the camera.
•► It is not possible to exit Playback Mode except by turning off the camera.
Removable Disk Mode
•Make sure a memory card is inserted and the camera is turned off.
•onnect the camera to the P using a standard USB cable. The green LED may turn on
indicating that the battery is charging.
•The blue LED will turn on for about a second but will then be replaced by the yellow LED.
After a short while the yellow LED may also turn off.
•The camera is now in Disk Mode and a new removable drive should be available on your
computer. This may take up to 30 seconds.
•► You cannot record video or photos if the camera is connected to the P in Removable Disk
Mode.
•► It is not possible to enter Removable Disk Mode when using a Video-Out cable (pins #4 and
#5 shorted to ground).
Webcam Mode
There are two ways in which you can enter webcam mode.
Method 1:
•onnect the camera as a removable drive (see above).
•Press the Shutter button to enter webcam mode.
•► If this is the first time you have connected the camera in Web am mode, Windows will
automatically install the required drivers.
•► Disconnect the camera or press the Power button to exit webcam mode.
Method 2:
•Remove the flash memory card.
•onnect the camera to the P using a standard USB cable.
•The yellow LED will blink at 2 second intervals indicating there is no card inserted. This is
normal.
•► If this is the first time you have connected the camera in Web am mode, Windows will
automatically install the required drivers.
•The camera is now in Webcam mode.
•Start your favorite Web am software, such as AM ap. If your screen is black, the software is
not configured correctly. Make sure the program shows the "USB P camera" as the "device"
selected for video capture. If this option does not show in the "device" option list, restart the
webcam program and check again.
•Disconnect the camera or press the Power button to exit webcam mode.
►Note: Windows XP has an integrated Web am viewer. Your Mobius should be visible in Explorer
(My omputer) as a "USB Video Device". This functionality does not exist in Windows 7.
In-Camera Formatting
The amera contains a built-in formatter which may be used to format the SD card. In- amera
formatting is best done using mSetup.exe (see below) but can also be done as follows:
•onnect the camera to an External USB power supply or to a P as a Removable disk (see
above).
•Press and hold down the Mode button. DO NOT RELEASE the button until after the next
steps are completed.
•Disconnect the camera from the power supply or the computer.
•The yellow LED will blink for a few seconds followed by three blinks of the red LED, after
which the camera will turn off. You must wait until you see the red LED blink three times.
•Release the Mode button.
►In firmware versions up to v2.03 cards with a capacity greater than 32GB will be formatted with
exFAT. All other cards will be formatted as FAT32. See the note about using exFAT in older operating
systems in the Description.
Camera Setup (Configuration
On Windows it is recommended to always use the program mSetup.exe to modify the camera's
configuration. mSetup communicates directly with the camera and makes configuring the camera a
very simple task.
It is, however, also possible to manually change the configuration settings by editing the
"SYS FG.TXT" file which must be placed in the root folder of the card for the camera to find and load
the new settings. You can use any AS II editor, for example Notepad, to modify the parameters. The
"SYS FG.TXT" must be in plain AS II, it must not be in Unicode. If you don't know what a root
folder is, or you don't know what AS II is or don't know how to manually edit AS II files please only
use mSetup.exe.
A "SYS FG.TXT" file must first be generated by the amera. The camera's parameters are self
explanatory. It is important not to change the sequence of the square brackets and not configure invalid
combinations. For example, never combine a clip longer than 5 minutes with the continuous loop. If
you enter invalid combinations or values, the amera will not perform as expected. It is much safer to
use the setup program which will always configure the camera correctly. If you want to keep the
camera's current date and time, replace all the numeric characters withing the square brackets by ?.
The "SYS FG.TXT" file can be automatically generated as follows:
1. Disconnect the camera from the P and turn it off.
2. Press and Hold Down the Mode button. DO NOT RELEASE the button until step 4.
3. Press and Hold Down the Power button until the RED LED blinks 3 times and the camera
turns off. This will take about 5 seconds. During the process, the blue and yellow LEDs may
blink.
4. Release the Mode and Power buttons.
The SYS FG.TXT file showing the camera's current settings should now be in the memory card root
folder. Now you can edit the SYS FG.TXT file as indicated above, and load the new settings back into
the camera by using exactly the same method as outlined in steps 1 through 4, above. Once completed,
the "SYS FG.TXT" file will be automatically deleted from the card's root folder.
►Some parameter settings are not allowed in combination with other parameter settings. For example,
only clip lengths of 5 minutes and less are allowed when loop recording is enabled. The Windows
configuration setup program mSetup.exe (see below) guarantees the settings are valid. Use the tool tips
to show you which parameter combinations are allowed and which are not allowed. If you edit the
SYS FG.TXT and enter invalid values the results are undefined and will lead to unexpected results.
Using Software to configure the camera
The Windows program mSetup.exe will automatically configure the camera with the parameters you
require. Detailed instructions can be found in the program by clicking the "Help" button. The program
is also used to synchronize the camera's internal clock with the computer's date and time.
►An official configuration tool which will work with many Android devices can be found in Google's
Play Store. Search for "therau2000" to list programs by this author.
Firmware Update
Normally, there is no need to update the firmware. You should only update the firmware if you are
having problems with the current firmware or the new firmware provides functionality you require that
are not available in your current version.
The latest firmware version can be downloaded and installed directly from the setup program or
installed manually by downloading the firmware file from
http://www.rcgroups.com/forums/showpost.php?p=25170908&postcount=3.
Updating the firmware is an easy and safe process, but you should take note that it is not possible to
update the firmware using SD cards with a capacity greater than 32GB unless they are formatted
to FAT32. The firmware update routine is a low-level routine called before the exFAT file system is
loaded. The low-level routine only supports the FAT32 file system.
Automatic Firmware Update
Use mSetup (Tools) to automatically update the firmware. This is by far the easiest method.
Manual Firmware Update
DO NOT PRESS ANY BUTTONS during the firmware update process.
There are two methods with which you can update the firmware.
Method 1 without pressing any buttons:
•Turn off the camera.
•onnect the camera to the computer and wait until the card is recognized as a Removable Drive.
•opy the new firmware file into the camera's flash card root folder. All firmware files are
named FWTL AM.BIN. The name must not be changed.
•Disconnect the camera from the computer and wait until it turns off.
•Wait until all the LEDs are turned off.
•onnect the camera to the P . The blue LED will turn on for about 13 seconds and then begin
to flash. WAIT.
•After another 7 seconds the blue LED will turn off. WAIT.
•After a second or two the yellow LED will turn on. WAIT
•The firmware file will be automatically deleted.
•The camera will automatically be connected as a removable device.
•After about 4 seconds the process is complete and the yellow LED will turn off.
•The camera is now ready for use as a USB drive.
Method 2 by pressing the power button :
•Turn off the camera.
•onnect the camera to the computer and wait until the card is recognized as a Removable Drive.
•opy the new firmware file into the camera's flash card root folder. All firmware files are
named FWTL AM.BIN. The name must not be changed.
•Disconnect the camera from the computer and wait until it turns off.
•Wait until all the LEDs are turned off.
•Turn on the camera and WAIT.
•The blue LED will turn on for about 13 seconds and then begin to flash. WAIT.
•After another 7 seconds the blue LED will turn off. WAIT.
•After a second or two the yellow LED will turn on indicating the firmware file has been
automatically deleted.
•The camera is now in standby mode and ready for use.
Recording using an external power supply
With the Mobius, it is possible to charge the battery and record at the same time using a standard
external USB 5V D power supply. The power supply may be mains driven (normal household wall
plug), or run off batteries, including the car charger USB plug (optional accessory) and cable supplied
with the camera.
External USB power supplies usually only use the +5V and the - (Ground/Earth) wires. The 2 data
wires are normally not used. However, some USB power supplies designed for a specific USB device
may use different wiring schemes and thus may not work with this camera. To avoid possible problems,
always use a generic power supply.
When turned on, the camera checks for an electric signal on the two Data wires. If a signal is found, the
camera assumes it is connected to a P and recording will not be possible - see below "Recording
when directly connected to a P ".
For recording video or taking pictures using a standard external power supply connection, the USB
power supply can be connected at any time, i.e. before the camera is turned on, before the recording is
started, or after the recording has been started.
►Only use a quality chargers capable of supplying 1000mA (1A) and a stable voltage of at least 5V.
Low quality chargers may not be able to supply enough current and can lead to premature battery
failure or, in the worst case, even destroy the camera.
Recording when directly connected to a PC
With the Mobius, it is possible to charge the battery and record videos or time-lapse photos at the same
time while connected to a P for charging only. You cannot access the SD while recording.
In order to do this, the video or time-lapse photo recording must be started before the camera is
connected to the P . It is not possible to record if the camera is turned on while connected to a P .
Likewise it is not possible to take single still pictures while the camera is connected to the P .
Additional information
The following functions/parameters need additional explanation:
Power On Default
The Mobius startup mode can be set to Video Mode 1, Video Mode 2 or Photo Mode. The setting will
have a direct influence on the Auto Power-on Record parameter (see below).
Power On - Auto Record
If this parameter is set the Mobius will start recording as soon as external USB power is connected or
Otros manuales para ActionCam
1
Tabla de contenidos
Otros manuales de Cámara de acción de Mobius
