MK Diamond Products MK-100 TRACKER Manual del sistema

MK-100 TRACKER

CAUTION:

Read all safety and

operating instructions

before using this

ment

TILE SAW

OWNER’S MANUAL &

OPERATING INSTRUCTIONS

Enter the Serial Number of your new saw in the

space below. The Serial Number is located on the

left side of the blade guard.

NOTE:

For your (1) one year warranty to be effective,

complete the warranty card (including the Serial

Number and mail it in as soon as possible.

SERIAL NUMBER:

MK-100 TRACKER Revision 02/03, Effective Date February 12, 2003 Page 2

INTRODUCTION

We at MK Diamond want to congratulate you on selecting the MK-100 TRACKER Tile Saw. We are certain

that you will be pleased with your purchase. MK Diamond takes pride in producing the finest products in the

industry.

Operated correctly, your MK-100 TRACKER should provide you with years of quality service. In order to help

you, we have included this manual. This owner’s manual contains information necessary to operate and

maintain your MK-100 TRACKER safely and correctly. Please take a few minutes to familiarize yourself with

the MK-100 TRACKER by reading and reviewing this manual.

If you should have questions concerning your MK-100 TRACKER, please feel free to call our friendly customer

service department at: 800 421-5830

Regards,

MK Diamond

MK-100 TRACKER Revision 02/03, Effective Date February 12, 2003 Page 3

TABLE OF CONTENTS

Page

SAFETY: 4

Safety Messages 4

Damage Prevention Message 4

General Safety Precautions and Hazard Symbols 4

California Proposition 65 Message 6

Electrical Requirements and Grounding Instructions 7

Safety Label Locations 9

Tile Saw Specific Warnings 9

Product Specifications 10

UNPACKING, TRANSPORT, UNIVERSAL STAND, and ASSEMBLY

Unpacking 11

Contents 11

Transport 11

UniversalStand 12

Assembly 13

SETUP, ADJUSTMENT AND OPERATION

Setup 16

Adjustment and Operation 19

Cleanup 26

MAINTENANCE AND TROUBLESHOOTING

Maintenance 27

Troubleshooting 38

EXPLODED VIEW AND PARTS LIST

Exploded View 39

PartsList 40

THEORY

Theory of Diamond Saws 43

ACCESSORIES

Accessories 44

ORDERING and RETURN INSTRUCTIONS

Ordering Information 45

Return Material Policy 45

PackagingInstructions 45

Authorized Service Centers 45

MK-100 TRACKER Revision 02/03, Effective Date February 12, 2003 Page 4

SAFETY

Read and follow all safety, operating and maintenance instructions. Failure to read and follow these

instructions could result in injury or death to you or others. Failure to read and follow these instructions could

also result in damage and/or reduced equipment life.

SAFETY MESSAGES:

Safety messages inform the user about potential hazards that could lead to injury, death and/or equipment

damage. Each safety message will be preceded by one of the following (3) three words that identify the

severity of the message.

Not following instructions WILL lead to DEATH or SERIOUS INJURY

Not following instructions COULD lead to DEATH or SERIOUS INJURY

Not following instructions CAN lead to injury

DAMAGE PREVENTION AND INFORMATION MESSAGES:

A Damage Prevention Message is to inform the user of important information and/or instructions that could

lead to equipment or other property damage if not followed. Information Messages convey information that

pertains to the equipment being used. Each message will be preceded by the word NOTE, as in the example

below.

NOTE:

Equipment and/or property damage may result if these instructions are not followed.

GENERAL SAFETY PRECAUTIONS AND HAZARD SYMBOLS:

In order to prevent injury, the following safety precautions and symbols should be followed at all times!

Safety Precautions:

KEEP GUARDS IN PLACE.

REMOVE ADJUSTING KEYS AND WRENCHES.

Form a habit of checking to see that keys and adjusting wrenches are removed from the power tool before it

is turned on.

KEEP WORK AREA CLEAN.

Cluttered work areas and benches invite accidents.

DO NOT USE IN DANGEROUS ENVIRONMENTS.

Do not use power tools in damp or wet locations nor expose them to rain. Always keep the work area well

lighted.

KEEP CHILDREN AWAY.

All visitors and children should be kept a safe distance from work area.

MAKE THE WORKSHOP KID PROOF.

Make the workshops kid proof by using padlocks, master switches or by removing starter keys.

DO NOT FORCE THE TOOL.

A power tool will do a job better and safer operating at the rate for which it was designed.

USE THE RIGHT TOOL.

Do not force a tool or an attachment, to do a job that it was not designed to do.

In order to prevent injury, keep guards in place and in working order at all times.

MK-100 TRACKER Revision 02/03, Effective Date February 12, 2003

Page 5

SAFETY

USE THE PROPER EXTENSION CORD.

If using an extension cord make sure it is in good condition first. When using an extension cord, be sure to

use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in

line voltage that will result in a loss of power and overheating. TABLE 1, Page 7 shows the correct AWG

size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gage.

The smaller the gage number, the heavier the cord.

WEAR PROPER APPAREL.

Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry that may be caught in moving

parts. Non-slip footwear is recommended. Wear protective hair covering to contain long hair.

ALWAYS USE SAFETY GLASSES.

Safety glasses should always be worn when working around power tools. In addition, a face,

dust mask or respirator should be worn if a cutting operation is dusty. Everyday eyeglasses only

have impact resistant lenses and may not prevent eye injury-they are NOT safety glasses.

SECURE WORK.

Clamps or a vise should be used to hold work whenever practical. Keeping your hands free to operate a

power tool is safer.

DO NOT OVERREACH.

Keep proper footing and balance at all times by not overreaching.

MAINTAIN TOOLS WITH CARE.

Keep tools clean for the best and safest performance. Always follow maintenance instructions for

lubricating, and when changing accessories.

DISCONNECT TOOLS.

Power tools should always be disconnected before servicing or when changing accessories, such as blades,

bits, cutters, and the like.

REDUCE THE RISK OF UNINTENTIONAL STARTING.

Make sure the trigger switch; locking button is in the RELEASE position before plugging in a power

tool.

USE RECOMMENDED ACCESSORIES.

Consult the owner's manual for recommended accessories. Using improper accessories may increase the

risk of personal or by-stander injury.

NEVER STAND ON THE TOOL.

Serious injury could occur if a power tool is tipped, or if a cutting tool is unintentionally contacted.

CHECK FOR DAMAGED PARTS.

Before using a power tool, check for damaged parts. A guard or any other part that is damaged should be

carefully checked to determine it would operate properly and perform its intended function. Always check

moving parts for proper alignment or binding. Check for broken parts and mountings and all other conditions

that may affect the operation of the power tool. A guard, or any damaged part, should be properly repaired

or replaced.

DIRECTION OF FEED.

Always feed work into a blade or cutter against the direction of rotation. A blade or cutter should always be

installed such that rotation is in the direction of the arrow imprinted on the side of the blade or cutter.

NEVER LEAVE A TOOL RUNNING UNATTENDED – TURN POWER OFF.

Do not leave a tool until it comes to a complete stop. Always turn a power tool OFF when leaving the work

area, or, when a cut is finished.

MK-100 TRACKER Revision 02/03, Effective Date February 12, 2003

Page 6

SAFETY

Hazard Symbols:

ELECTRICAL SHOCK!

Never touch electrical wires or components while the motor is running. Exposed, frayed or worn

electrical motor wiring can be sources of electrical shock that could cause severe injury or burns.

ACCIDENTAL STARTS!

Before plugging the equipment into an electrical outlet, be sure the trigger switch, locking button is in

the "RELEASE" position to prevent accidental starting. Unplug the power tool before performing any

service operation.

ROTATING OR MOVING PARTS!

Keep hands, feet, hair, and clothing away from all moving parts to prevent injury. Never operate a

power tool with covers, shrouds, or guards removed.

Sawing and drilling generates dust. Excessive airborne particles may cause irritation to eyes, skin and

respiratory tract. To avoid breathing impairment, always employ dust controls and protection suitable to the

material being sawed or drilled; See OSHA (29 CFR Part 1910.1200). Diamond Blades improperly used are

dangerous. Comply with American National Standards Institute Safety Code, B7.1 and, Occupational Safety

and Health Act covering Speed, Safety Guards, Flanges, Mounting Procedures, General Operating Rules,

Handling, Storage and General Machine Conditions.

CALIFORNIA PROPOSITION 65 MESSAGE:

Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contain

chemicals known [to the State of California] to cause cancer, birth defects or other reproductive harm. Some

examples of these chemicals are:

• Lead, from lead-based paints

• Crystalline silica, from bricks and cement and other masonry products and

• Arsenic and chromium, from chemically treated lumber

For further information, consult the following sources:

http://www.osha-slc.gov/sltc/silicarystalline/index.html

http://www.oehha.org/prop65/out_of_date/6022kLstA.html

Your risk from these exposures varies depending on how often you do this type of work. To reduce your

exposure to these chemicals, work in a well-ventilated area, and work with approved safety equipment, such

as those dust masks that are specially designed to filter out microscopic particles.

MK-100 TRACKER Revision 02/03, Effective Date February 12, 2003

Page 7

SAFETY

ELECTRICAL REQUIREMENTS AND GROUNDING INSTRUCTIONS:

In order to prevent potential electrical shock and injury, the following electrical safety precautions and symbols

should be followed at all times!

In case of a malfunction or breakdown, grounding provides a path of least resistance for electric

current to reduce the risk of electric shock. This tool is equipped with an electric cord having an

equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching

outlet that is properly installed and grounded in accordance with all local codes and ordinances.

• Do not modify the plug provided – if it will not fit the outlet; have the proper outlet installed by a

qualified electrician

• Improper connections of the equipment-grounding conductor can result in a risk of electric shock.

The equipment-grounding conductor is the insulated conductor that has an outer surface that is

green, with or without yellow stripes. If repair or replacement of the electric cord or plug is

necessary, do not connect the equipment-grounding conductor to a live terminal

• Check with a qualified electrician or service personnel if the grounding instructions are not

completely understood, or if in doubt as to whether the tool is properly grounded

• Use only 3-wire extension cords that have 3-prong grounding plugs and 3-pole receptacles that

accept the tool's plug

• Repair or replace a damaged or worn cord immediately

This tool is intended for use on a circuit that has an outlet that looks like the one shown in Sketch A

of Figure 1. The tool has a grounding plug that looks like the plug illustrated in Sketch A of FIGURE

1. A temporary adapter, which looks like the adapter illustrated in sketches B and C, may be used to

Connect this plug to a 2-pole receptacle as shown in Sketch B, if a

properly grounded outlet is not available. The temporary adapter

should be used only until a properly grounded outlet can be

installed by a qualified electrician. The green-colored rigid ear,

lug, and the like, extending from the adapter, must be connected

to a permanent ground such as a properly grounded outlet box.

NOTE: Use of a temporary adapter is not permitted in Canada.

To reduce the risk of electrocution, keep all connections dry and off the ground.

A Ground Fault Circuit Interrupter (GFCI) should be provided on the circuit(s) or outlet(s) to be used

for the Tile Saw. Receptacles are available having built-in GFCI protections and may be used for

this measure of safety.

When using an extension cord, the GFCI should be installed closest to the power source, followed

by the extension cord and lastly, the saw.

eta

Cover of Grounded

Outlet Box

(

)

(

)

(

)

(

)

DAPTER

Grounding

Means

Grounding

FIGURE 1

MK-100 TRACKER Revision 02/03, Effective Date February 12, 2003

Page 8

SAFETY

To avoid the possibility of the appliance plug or receptacle getting wet, position the saw to one side

of a wall mounted receptacle. This will prevent water from dripping onto the receptacle or plug. A

"drip loop," shown in FIGURE 2, should be arranged by the user to properly position the power cord

relative to the power source.

The "drip loop" is that part of the cord below the level of the receptacle, or

the connector, if an extension cord is used. This method of positioning the

cord prevents the travel of water along the power cord and coming in

contact with the receptacle.

If the plug or receptacle gets wet, DO NOT unplug the cord. Disconnect

the fuse or circuit breaker that supplies power to the tool. Then unplug and

examine for presence of water in the receptacle.

Use only extensions cords that are intended for outdoor use. These extension cords are identified

by a marking "Acceptable for use with outdoor appliances; store indoors while not in use." Use only

extension cords having an electrical rating not less than the rating of the product. Do not use

damaged extension cords. Examine extension cords before using and replace if damaged. Do not

abuse extension cords and do not yank on any cord to disconnect. Keep cords away from heat and

sharp edges. Always disconnect the extension cord from the receptacle before disconnection the

product form the extension cord.

To reduce the risk of electrocution, keep all connections dry and off the ground. Do not touch the

plug with wet hands.

Use of undersize extension cords result in low voltage to the motor that can result in motor burnout

and premature failure. MK Diamond warns that equipment returned to us showing signs of being run

in a low voltage condition, through the use of undersized extension cords will be repaired or replaced

totally at the customer’s expense. There will be no warranty claim.

To choose the proper extension cord,

• Locate the length of extension cord needed in TABLE 1 below.

• Once the proper length is found, move down the column to obtain the correct AWG size required

for that length of extension cord.

As an example, a fifty (50) foot extension cord would require an AWG size of 16.

Extension Cord Minimum Gage for Length

Volts Total Length of Cord in Feet

120V 25 ft. 50 ft. 100 ft 150 ft.

AWG AWG AWG AWG

14 12 Not Recommended

TABLE 1

Supporting

Surface

Power

Tool

Drip Loop

Power

Cord

FIGURE 2

MK-100 TRACKER Revision 02/03, Effective Date February 12, 2003

Page 9

SAFETY

SAFETY LABEL LOCATIONS:

Safety labels are located according to Figures 1 through 4 below. The labels contain important safety

information. Please read the information contained on each safety label. These labels are considered a

permanent part of your saw. If a label comes off or becomes hard to read, contact MK Diamond or your

dealer for a replacement

Item Location Description Part No.

1A. Motor Rear Caution Use Ground Fault Interrupt 155678

1B. Motor Rear Caution Receptacle for Pump Only 154822

1C. Motor Rear Service or Warranty Information 155038

2. Blade Guard Serial Number 157249-01

3A Motor Front Warning Read and Follow Operating Instructions 155806

3B Motor Front Motor Specifications N/A

4A Pump Left Side Warning Connect to Grounded Receptacle N/A

4B Pump Right Side Pump Specifications N/A

TILE SAW SPECIFIC WARNINGS:

Wear eye protection.

Use splash hood for every operation for which it can be used.

Disconnect saw before servicing, when changing cutting blades, and cleaning.

Use tool only with smooth edge cutting blades free of openings and grooves.

Replace damaged cutting blade before operating.

A B

1 2

A B

MK-100 TRACKER Revision 02/03, Effective Date February 12, 2003

Page 10

SAFETY

PRODUCT SPECIFICATIONS:

The MK-100 TRACKER is a versatile Tile Saw. Operated and used according to this manual, the MK-100

TRACKER will provide years of dependable service.

General Description:

The MK-100 TRACKER Tile Saw is engineered as a tabletop or stand mounted wet tile saw. The saw

includes a powerful 115v totally enclosed capacitor start GE motor with a thermal protective overload. The

saw is capable of cutting tile up to twenty (20) inches in length, or diagonal cutting tile up to fourteen (14)

inches. The saw can cut an object three and one-half (3-1/2) inches thick in one pass.

Motor Specifications:

Motor specifications for the MK-100 TRACKER are listed in Table 2 below.

Voltage 115 v

Overall Amperage 13.4 a

Motor Only Amperage 12.8 a

Frequency 60 Hz

RPM 3450 rpm

Horse Power 1.5 hp

Weight 97 lbs

Table 2

Thermal Overload Protection:

The motor is protected by a thermal overload equipped with a manual reset.

Blade Capacity:

The MK-100 TRACKER uses a ten (10) inch (254mm) diameter, wet cutting continuous rim, MK Diamond

blade with a one-sixteenth 1/16 inch (15.875 mm) cutting width and a five-eighths (5/8) inch (15.875 mm)

arbor.

Tile Types:

The MK-100 TRACKER can cut a variety of tile types including Porcelain, Terracotta, Marble, Quarry and

Slate, or almost any other non-ferrous material.

NOTE:

The MK-100 TRACKER is not designed to cut plastic or ferrous (metals) material.

Tabla de contenidos

Otros manuales de Sierra de MK Diamond Products

MK Diamond Products

MK Diamond Products MK-370EXP TILE SAW Manual de usuario

MK Diamond Products

MK Diamond Products CX-3 Honda GX160 Manual de usuario

MK Diamond Products

MK Diamond Products MK- 2005G Manual del sistema

MK Diamond Products

MK Diamond Products MK-145 Manual del sistema

MK Diamond Products

MK Diamond Products 160028 Manual de usuario

MK Diamond Products

MK Diamond Products MK-1280 Manual de usuario

MK Diamond Products

MK Diamond Products MK-2000 PRO Series Documento técnico

MK Diamond Products

MK Diamond Products MK-170 SERIES Manual de usuario

MK Diamond Products

MK Diamond Products MK-5005S Manual de usuario

MK Diamond Products

MK Diamond Products MK-2013 HSP Manual de usuario

MK Diamond Products

MK Diamond Products MK-101 PRO24 Manual de usuario

MK Diamond Products

MK Diamond Products MK-101 Instrucciones originales

MK Diamond Products

MK Diamond Products MK-2000 PRO Series Documento técnico

MK Diamond Products

MK Diamond Products 166110 Guía de aplicación

MK Diamond Products

MK Diamond Products MK-370 Manual de usuario

MK Diamond Products

MK Diamond Products MK-145 Manual del sistema

MK Diamond Products

MK Diamond Products TX-3 Guía de aplicación

MK Diamond Products

MK Diamond Products MK-212 Series Manual del sistema

MK Diamond Products

MK Diamond Products MK-370EXP TILE SAW Manual de usuario

MK Diamond Products

MK Diamond Products MK-2424HSP Manual del sistema

MK Diamond Products

MK Diamond Products MK-101-24 Manual de usuario

MK Diamond Products

MK Diamond Products MK-170 SERIES Manual del sistema

MK Diamond Products

MK Diamond Products 157721X Manual de usuario

MK Diamond Products

MK Diamond Products MK-660 SERIES Manual de usuario

Manuales populares de Sierra de otras marcas

RIDGID

RIDGID BS1400 Manual de usuario

ATIKA

ATIKA BWS 400-2 Manual de usuario

RGC

RGC FS20 Manual de usuario

Makita

Makita M2300 Manual de usuario

IMET Spa

IMET Spa BASIC 300 PLUS SHI Manual de usuario

IMET Spa

IMET Spa SIRIO 370 AF-E Manual de usuario

Optimum

Optimum OPTisaw CS 275 Manual de usuario

Makita

Makita BPB180 Manual de usuario

Stihl

Stihl MS 462 C-M Manual de usuario

AEG

AEG TS 250 K Manual de usuario

Meec tools

Meec tools 004665 Manual de usuario

Makita

Makita LS1018L Manual de usuario

Ryobi

Ryobi RCS1400 Manual de usuario

DeWalt

DeWalt DCS391 Manual de usuario

Sealey

Sealey SA72 Manual de usuario

skilsaw

skilsaw SPT88 Instrucciones de montaje

Urrea

Urrea SI810 Dimensiones y guía de instalación

EINHELL

EINHELL BKG 210/1 Manual de usuario