Mitsubishi AE-200A Manual de usuario

Contents

1. Introduction .........................................................................3

1-1. What is AE-200 Update Tool?.....................................................3

1-2. PC requirements.........................................................................3

1-3. System descriptions....................................................................4

1-4. System restrictions .....................................................................5

2. Preparation .........................................................................6

2-1. How to obtain the update file ......................................................6

2-2. Installation procedures of Update Tool........................................6

2-3. Setting the PC’s IP address ........................................................8

2-4. Installation procedures of .NET Framework................................9

3. Usage instructions ............................................................10

3-1. Main screen ..............................................................................11

3-2. Inputting the IP addresses of centralized controllers ................13

3-3. Checking the versions of the centralized controllers ................15

3-4. Selecting the update file ...........................................................17

3-5. Updating the centralized controllers .........................................18

3-6. Saving the IP addresses of centralized controllers...................21

4. Troubleshooting ................................................................22

Air Conditioning Control System

Centralized Controller

AE-200A/AE-50A/EW-50A

AE-200E/AE-50E/EW-50E

Update Tool Instruction Book

Before using the controller,

please read this Instruction

Book carefully to ensure proper

operation.

Retain this manual for future

reference.

For distribution to dealers and contractors

WT08302X01

Terms used in this manual

- “Centralized Controller AE-200A/AE-200E” is referred to as “AE-200”.

- “Centralized Controller AE-50A/AE-50E” is referred to as “AE-50”.

- “Centralized Controller EW-50A/EW-50E” is referred to as “EW-50”.

WT08302X01

1. Introduction

1-1. What is AE-200 Update Tool?

Update Tool is a tool that can update the software of all AE-200/AE-50/EW-50 controllers that are connected in the

air conditioning control system at once.

1-2. PC requirements

Item Requirements

CPU 1 GHz or better (at least 2 GHz recommended)

Memory 2 GB or better

Screen resolution 1024 x 768 or better

Windows 7 (32bit/64bit)

Windows 8.1 (64bit)

Windows 10 (64bit)

* .NET Framework 4.0 or later is required.

Internal LAN port or LAN card 100 BASE-TX or better

Pointing device Mouse, etc.

Max. 50 controllers

AE-200/AE-50/EW-50

Update file

Update file AE-200/AE-50/EW-50

AE-200/AE-50/EW-50

WT08302X01

1-3. System descriptions

The system configuration image is shown below.

Important

•When connecting the AE-200/AE-50/EW-50 via a LAN, be sure to use the “LAN1” port.

AE-200AE-200

LAN

HUB

AE-50/EW-50

HUB

AE-50/EW-50

Max. 50 controllers

AE-50/EW-50

WT08302X01

1-4. System restrictions

•AE-200 Update Tool is exclusively used for AE-200/AE-50/EW-50. Do not use this tool for other products.

•The AE-200/AE-50/EW-50 software cannot be downgraded to an earlier version.

•Up to 50 AE-200/AE-50/EW-50 controllers can be updated at the same time.

Note

•The communication between AE-200/AE-50/EW-50 and the air conditioning units will stop while the software

is being updated. Although the unit in operation may detect a communication error and an error sign may

appear on the local remote controllers, the unit will continue its operation and be operable from the local

remote controllers.

* Note that Mr. Slim indoor units or systems with no local remote controllers may detect a communication error and come to an abnormal

stop.

•While the software is being updated, up to 60-minute worth of energy management data and billing function

data will not be recorded.

•When an AE-50/EW-50’s Pulse Input (PI) function is used, the pulse that is input while the software is being

updated will not be counted.

Important

•Record the operation status of the air conditioning units immediately before updating the software. After the

software update is completed, check the operation status of the units, and manually operate the units as

necessary.

•Some operations and functions, such as scheduled operations, billing function, Peak Cut control, energy

management function, will be disabled while the software is being updated. Check the setting details of these

functions beforehand, and update the software when it does not affect these functions.

•If the functions in the table below are used, avoid updating the AE-200/AE-50/EW-50 software during the time

period indicated in the right column.

Function in use Time period in which the update is prohibited

Electricity charge apportioning function

(with Charge Calculation Tool) AM 5:00 – 5:10

Electricity charge apportioning function (with TG-2000A) AM 4:05 – 4:35

Malfunction log backup (with TG-2000A) AM 0:05 – 0:15

Peak Cut data backup (with TG-2000A) AM 2:00 – 2:10

Measurement trend data backup

(with PI controller, AI controller, or TG-2000A) AM 1:05 – 1:15

WT08302X01

2. Preparation

2-1. How to obtain the update file

For how to obtain the latest update file, contact the dealer from which the Update Tool was obtained.

2-2. Installation procedures of Update Tool

Important

•If your OS is Windows 7, check beforehand that .NET Framework version 4.0 or later is installed.

Refer to section 2-4 “Installation procedures of .NET Framework” for details.

Note

•The version of the installed .NET Framework can be checked by selecting the Windows Start menu and then

choosing [Control Panel] > [Program and Features].

Procedures

1. Double-click “AE-200 UpdateTool_V***.msi” that was downloaded.

* “V***” indicates version number. (“V100” indicates Ver. 1.00.)

2. If the “Security Warning” message appears, click [Run].

3. When the “Setup Wizard” screen appears, click [Next].

4. The “License Agreement” screen will appear. Read through,

select [I Agree], and click [Next].

WT08302X01

5. The “Select Installation Folder” screen will appear. Select the

save destination folder and click [Next].

Note

•To allow all users who can login the PC to have access to the

Update Tool, check that the [Everyone] checkbox is selected

and then click [Next].

6. When the “Confirm Installation” screen appears, click [Next].

7. The Update Tool will be installed.

8. Once installation is completed, click [Close].

WT08302X01

2-3. Setting the PC’s IP address

Set the PC’s IP address so that settings data can be sent from the Update Tool to the AE-200/AE-50/EW-50.

When setting the PC’s IP address, set a network address in the same system as the IP address for the

AE-200/AE-50/EW-50.

(Example: AE-200 IP address: 192.168.11.1; PC IP address: 192.168.11.150)

When connecting the AE-200/AE-50/EW-50 to an existing LAN, consult the system administrator to decide the IP

address.

Procedures

1. Click [Control Panel] in the Start menu.

2. Click [Network and Sharing Center] > [Local Area Connection].

3. In the “Local Area Connection Status” window, click [Properties].

4. Click [Internet Protocol Version 4 (TCP/IPv4)] to select it, and click

[Properties].

WT08302X01

5. In the [Internet Protocol Version 4 (TCP/IPv4) Properties] window,

check the radio button next to [Use the following IP address].

6. Enter the PC’s IP address (e.g., [192.168.11.150]) in “IP address”.

7. Enter the subnet mask [255.255.255.0] (unless otherwise specified)

in “Subnet mask”.

8. In “Default gateway”, enter the gateway address as necessary.

Important

•Consult the system administrator to decide the IP, subnet mask, and gateway addresses.

•Take a note of the IP, subnet mask, and gateway addresses before changing them.

9. Keep clicking [OK] or [Close] to close all windows.

2-4. Installation procedures of .NET Framework

If .NET Framework 4.0 is not already installed, download the .NET Framework 4.5.2 installer from the URL shown

below, and then install it.

URL for when the Internet is connected (Web installer) (English):

http://www.microsoft.com/en-US/download/details.aspx?id=42643

URL for when the Internet is not connected (Offline installer) (English):

http://www.microsoft.com/en-US/download/details.aspx?id=42642

* Other language can also be selected from this website.

Important

•If the system is not connected to the Internet, you will need to download the offline installer beforehand.

WT08302X01

3. Usage instructions

See the entire flowchart below to use the Update Tool. For details of each process, refer to the reference section

shown in the table below.

Process Reference section

(1) Main screen 3-1 “Main screen”

(2) Inputting IP address of centralized controller 3-2 “Inputting IP address of centralized controller”

(3) Checking the version of the centralized controller 3-3 “Checking the version of the centralized controller”

(4) Selecting the update file 3-4 “Selecting the update file”

(5) Authentication information input screen 3-5 “Updating the centralized controllers”

(6) Update 3-5 “Updating the centralized controllers”

(7) Confirming update completion 3-5 “Updating the centralized controllers”

(1) Main screen

(2) Inputting IP address of centralized controller

(3) Checking the version of the centralized controller

(4) Selecting the update file

Click “Acquire data”.

(5) Authentication information input screen

Click “Update”.

(6) Update

Enter ID and password, and click “OK”.

(7) Confirming update completion

Otros manuales para AE-200A

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de control de Mitsubishi

Mitsubishi

Mitsubishi MELSEC Q Series Manual de usuario